+// Updates should (hopefully) always be available at https://github.com/jrowberg/i2cdevlib
+//
+// Changelog:
+// 2019-07-08 - Added Auto Calibration routine
+// ... - ongoing debug release
+
+// NOTE: THIS IS ONLY A PARIAL RELEASE. THIS DEVICE CLASS IS CURRENTLY UNDERGOING ACTIVE
+// DEVELOPMENT AND IS STILL MISSING SOME IMPORTANT FEATURES. PLEASE KEEP THIS IN MIND IF
+// YOU DECIDE TO USE THIS PARTICULAR CODE FOR ANYTHING.
+
+/* ============================================
+I2Cdev device library code is placed under the MIT license
+Copyright (c) 2012 Jeff Rowberg
+
+Permission is hereby granted, free of charge, to any person obtaining a copy
+of this software and associated documentation files (the "Software"), to deal
+in the Software without restriction, including without limitation the rights
+to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+copies of the Software, and to permit persons to whom the Software is
+furnished to do so, subject to the following conditions:
+
+The above copyright notice and this permission notice shall be included in
+all copies or substantial portions of the Software.
+
+THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+THE SOFTWARE.
+===============================================
+*/
+
+#include "MPU6050.h"
+
+/** Specific address constructor.
+ * @param address I2C address, uses default I2C address if none is specified
+ * @see MPU6050_DEFAULT_ADDRESS
+ * @see MPU6050_ADDRESS_AD0_LOW
+ * @see MPU6050_ADDRESS_AD0_HIGH
+ */
+MPU6050::MPU6050(uint8_t address):devAddr(address) {
+}
+
+/** Power on and prepare for general usage.
+ * This will activate the device and take it out of sleep mode (which must be done
+ * after start-up). This function also sets both the accelerometer and the gyroscope
+ * to their most sensitive settings, namely +/- 2g and +/- 250 degrees/sec, and sets
+ * the clock source to use the X Gyro for reference, which is slightly better than
+ * the default internal clock source.
+ */
+void MPU6050::initialize() {
+ setClockSource(MPU6050_CLOCK_PLL_XGYRO);
+ setFullScaleGyroRange(MPU6050_GYRO_FS_250);
+ setFullScaleAccelRange(MPU6050_ACCEL_FS_2);
+ setSleepEnabled(false); // thanks to Jack Elston for pointing this one out!
+}
+
+/** Verify the I2C connection.
+ * Make sure the device is connected and responds as expected.
+ * @return True if connection is valid, false otherwise
+ */
+bool MPU6050::testConnection() {
+ return getDeviceID() == 0x34;
+}
+
+// AUX_VDDIO register (InvenSense demo code calls this RA_*G_OFFS_TC)
+
+/** Get the auxiliary I2C supply voltage level.
+ * When set to 1, the auxiliary I2C bus high logic level is VDD. When cleared to
+ * 0, the auxiliary I2C bus high logic level is VLOGIC. This does not apply to
+ * the MPU-6000, which does not have a VLOGIC pin.
+ * @return I2C supply voltage level (0=VLOGIC, 1=VDD)
+ */
+uint8_t MPU6050::getAuxVDDIOLevel() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_YG_OFFS_TC, MPU6050_TC_PWR_MODE_BIT, buffer);
+ return buffer[0];
+}
+/** Set the auxiliary I2C supply voltage level.
+ * When set to 1, the auxiliary I2C bus high logic level is VDD. When cleared to
+ * 0, the auxiliary I2C bus high logic level is VLOGIC. This does not apply to
+ * the MPU-6000, which does not have a VLOGIC pin.
+ * @param level I2C supply voltage level (0=VLOGIC, 1=VDD)
+ */
+void MPU6050::setAuxVDDIOLevel(uint8_t level) {
+ I2Cdev::writeBit(devAddr, MPU6050_RA_YG_OFFS_TC, MPU6050_TC_PWR_MODE_BIT, level);
+}
+
+// SMPLRT_DIV register
+
+/** Get gyroscope output rate divider.
+ * The sensor register output, FIFO output, DMP sampling, Motion detection, Zero
+ * Motion detection, and Free Fall detection are all based on the Sample Rate.
+ * The Sample Rate is generated by dividing the gyroscope output rate by
+ * SMPLRT_DIV:
+ *
+ * Sample Rate = Gyroscope Output Rate / (1 + SMPLRT_DIV)
+ *
+ * where Gyroscope Output Rate = 8kHz when the DLPF is disabled (DLPF_CFG = 0 or
+ * 7), and 1kHz when the DLPF is enabled (see Register 26).
+ *
+ * Note: The accelerometer output rate is 1kHz. This means that for a Sample
+ * Rate greater than 1kHz, the same accelerometer sample may be output to the
+ * FIFO, DMP, and sensor registers more than once.
+ *
+ * For a diagram of the gyroscope and accelerometer signal paths, see Section 8
+ * of the MPU-6000/MPU-6050 Product Specification document.
+ *
+ * @return Current sample rate
+ * @see MPU6050_RA_SMPLRT_DIV
+ */
+uint8_t MPU6050::getRate() {
+ I2Cdev::readByte(devAddr, MPU6050_RA_SMPLRT_DIV, buffer);
+ return buffer[0];
+}
+/** Set gyroscope sample rate divider.
+ * @param rate New sample rate divider
+ * @see getRate()
+ * @see MPU6050_RA_SMPLRT_DIV
+ */
+void MPU6050::setRate(uint8_t rate) {
+ I2Cdev::writeByte(devAddr, MPU6050_RA_SMPLRT_DIV, rate);
+}
+
+// CONFIG register
+
+/** Get external FSYNC configuration.
+ * Configures the external Frame Synchronization (FSYNC) pin sampling. An
+ * external signal connected to the FSYNC pin can be sampled by configuring
+ * EXT_SYNC_SET. Signal changes to the FSYNC pin are latched so that short
+ * strobes may be captured. The latched FSYNC signal will be sampled at the
+ * Sampling Rate, as defined in register 25. After sampling, the latch will
+ * reset to the current FSYNC signal state.
+ *
+ * The sampled value will be reported in place of the least significant bit in
+ * a sensor data register determined by the value of EXT_SYNC_SET according to
+ * the following table.
+ *
+ *
+ * EXT_SYNC_SET | FSYNC Bit Location
+ * -------------+-------------------
+ * 0 | Input disabled
+ * 1 | TEMP_OUT_L[0]
+ * 2 | GYRO_XOUT_L[0]
+ * 3 | GYRO_YOUT_L[0]
+ * 4 | GYRO_ZOUT_L[0]
+ * 5 | ACCEL_XOUT_L[0]
+ * 6 | ACCEL_YOUT_L[0]
+ * 7 | ACCEL_ZOUT_L[0]
+ *
+ *
+ * @return FSYNC configuration value
+ */
+uint8_t MPU6050::getExternalFrameSync() {
+ I2Cdev::readBits(devAddr, MPU6050_RA_CONFIG, MPU6050_CFG_EXT_SYNC_SET_BIT, MPU6050_CFG_EXT_SYNC_SET_LENGTH, buffer);
+ return buffer[0];
+}
+/** Set external FSYNC configuration.
+ * @see getExternalFrameSync()
+ * @see MPU6050_RA_CONFIG
+ * @param sync New FSYNC configuration value
+ */
+void MPU6050::setExternalFrameSync(uint8_t sync) {
+ I2Cdev::writeBits(devAddr, MPU6050_RA_CONFIG, MPU6050_CFG_EXT_SYNC_SET_BIT, MPU6050_CFG_EXT_SYNC_SET_LENGTH, sync);
+}
+/** Get digital low-pass filter configuration.
+ * The DLPF_CFG parameter sets the digital low pass filter configuration. It
+ * also determines the internal sampling rate used by the device as shown in
+ * the table below.
+ *
+ * Note: The accelerometer output rate is 1kHz. This means that for a Sample
+ * Rate greater than 1kHz, the same accelerometer sample may be output to the
+ * FIFO, DMP, and sensor registers more than once.
+ *
+ *
+ * | ACCELEROMETER | GYROSCOPE
+ * DLPF_CFG | Bandwidth | Delay | Bandwidth | Delay | Sample Rate
+ * ---------+-----------+--------+-----------+--------+-------------
+ * 0 | 260Hz | 0ms | 256Hz | 0.98ms | 8kHz
+ * 1 | 184Hz | 2.0ms | 188Hz | 1.9ms | 1kHz
+ * 2 | 94Hz | 3.0ms | 98Hz | 2.8ms | 1kHz
+ * 3 | 44Hz | 4.9ms | 42Hz | 4.8ms | 1kHz
+ * 4 | 21Hz | 8.5ms | 20Hz | 8.3ms | 1kHz
+ * 5 | 10Hz | 13.8ms | 10Hz | 13.4ms | 1kHz
+ * 6 | 5Hz | 19.0ms | 5Hz | 18.6ms | 1kHz
+ * 7 | -- Reserved -- | -- Reserved -- | Reserved
+ *
+ *
+ * @return DLFP configuration
+ * @see MPU6050_RA_CONFIG
+ * @see MPU6050_CFG_DLPF_CFG_BIT
+ * @see MPU6050_CFG_DLPF_CFG_LENGTH
+ */
+uint8_t MPU6050::getDLPFMode() {
+ I2Cdev::readBits(devAddr, MPU6050_RA_CONFIG, MPU6050_CFG_DLPF_CFG_BIT, MPU6050_CFG_DLPF_CFG_LENGTH, buffer);
+ return buffer[0];
+}
+/** Set digital low-pass filter configuration.
+ * @param mode New DLFP configuration setting
+ * @see getDLPFBandwidth()
+ * @see MPU6050_DLPF_BW_256
+ * @see MPU6050_RA_CONFIG
+ * @see MPU6050_CFG_DLPF_CFG_BIT
+ * @see MPU6050_CFG_DLPF_CFG_LENGTH
+ */
+void MPU6050::setDLPFMode(uint8_t mode) {
+ I2Cdev::writeBits(devAddr, MPU6050_RA_CONFIG, MPU6050_CFG_DLPF_CFG_BIT, MPU6050_CFG_DLPF_CFG_LENGTH, mode);
+}
+
+// GYRO_CONFIG register
+
+/** Get full-scale gyroscope range.
+ * The FS_SEL parameter allows setting the full-scale range of the gyro sensors,
+ * as described in the table below.
+ *
+ *
+ * 0 = +/- 250 degrees/sec
+ * 1 = +/- 500 degrees/sec
+ * 2 = +/- 1000 degrees/sec
+ * 3 = +/- 2000 degrees/sec
+ *
+ *
+ * @return Current full-scale gyroscope range setting
+ * @see MPU6050_GYRO_FS_250
+ * @see MPU6050_RA_GYRO_CONFIG
+ * @see MPU6050_GCONFIG_FS_SEL_BIT
+ * @see MPU6050_GCONFIG_FS_SEL_LENGTH
+ */
+uint8_t MPU6050::getFullScaleGyroRange() {
+ I2Cdev::readBits(devAddr, MPU6050_RA_GYRO_CONFIG, MPU6050_GCONFIG_FS_SEL_BIT, MPU6050_GCONFIG_FS_SEL_LENGTH, buffer);
+ return buffer[0];
+}
+/** Set full-scale gyroscope range.
+ * @param range New full-scale gyroscope range value
+ * @see getFullScaleRange()
+ * @see MPU6050_GYRO_FS_250
+ * @see MPU6050_RA_GYRO_CONFIG
+ * @see MPU6050_GCONFIG_FS_SEL_BIT
+ * @see MPU6050_GCONFIG_FS_SEL_LENGTH
+ */
+void MPU6050::setFullScaleGyroRange(uint8_t range) {
+ I2Cdev::writeBits(devAddr, MPU6050_RA_GYRO_CONFIG, MPU6050_GCONFIG_FS_SEL_BIT, MPU6050_GCONFIG_FS_SEL_LENGTH, range);
+}
+
+// SELF TEST FACTORY TRIM VALUES
+
+/** Get self-test factory trim value for accelerometer X axis.
+ * @return factory trim value
+ * @see MPU6050_RA_SELF_TEST_X
+ */
+uint8_t MPU6050::getAccelXSelfTestFactoryTrim() {
+ I2Cdev::readByte(devAddr, MPU6050_RA_SELF_TEST_X, &buffer[0]);
+ I2Cdev::readByte(devAddr, MPU6050_RA_SELF_TEST_A, &buffer[1]);
+ return (buffer[0]>>3) | ((buffer[1]>>4) & 0x03);
+}
+
+/** Get self-test factory trim value for accelerometer Y axis.
+ * @return factory trim value
+ * @see MPU6050_RA_SELF_TEST_Y
+ */
+uint8_t MPU6050::getAccelYSelfTestFactoryTrim() {
+ I2Cdev::readByte(devAddr, MPU6050_RA_SELF_TEST_Y, &buffer[0]);
+ I2Cdev::readByte(devAddr, MPU6050_RA_SELF_TEST_A, &buffer[1]);
+ return (buffer[0]>>3) | ((buffer[1]>>2) & 0x03);
+}
+
+/** Get self-test factory trim value for accelerometer Z axis.
+ * @return factory trim value
+ * @see MPU6050_RA_SELF_TEST_Z
+ */
+uint8_t MPU6050::getAccelZSelfTestFactoryTrim() {
+ I2Cdev::readBytes(devAddr, MPU6050_RA_SELF_TEST_Z, 2, buffer);
+ return (buffer[0]>>3) | (buffer[1] & 0x03);
+}
+
+/** Get self-test factory trim value for gyro X axis.
+ * @return factory trim value
+ * @see MPU6050_RA_SELF_TEST_X
+ */
+uint8_t MPU6050::getGyroXSelfTestFactoryTrim() {
+ I2Cdev::readByte(devAddr, MPU6050_RA_SELF_TEST_X, buffer);
+ return (buffer[0] & 0x1F);
+}
+
+/** Get self-test factory trim value for gyro Y axis.
+ * @return factory trim value
+ * @see MPU6050_RA_SELF_TEST_Y
+ */
+uint8_t MPU6050::getGyroYSelfTestFactoryTrim() {
+ I2Cdev::readByte(devAddr, MPU6050_RA_SELF_TEST_Y, buffer);
+ return (buffer[0] & 0x1F);
+}
+
+/** Get self-test factory trim value for gyro Z axis.
+ * @return factory trim value
+ * @see MPU6050_RA_SELF_TEST_Z
+ */
+uint8_t MPU6050::getGyroZSelfTestFactoryTrim() {
+ I2Cdev::readByte(devAddr, MPU6050_RA_SELF_TEST_Z, buffer);
+ return (buffer[0] & 0x1F);
+}
+
+// ACCEL_CONFIG register
+
+/** Get self-test enabled setting for accelerometer X axis.
+ * @return Self-test enabled value
+ * @see MPU6050_RA_ACCEL_CONFIG
+ */
+bool MPU6050::getAccelXSelfTest() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_ACCEL_CONFIG, MPU6050_ACONFIG_XA_ST_BIT, buffer);
+ return buffer[0];
+}
+/** Get self-test enabled setting for accelerometer X axis.
+ * @param enabled Self-test enabled value
+ * @see MPU6050_RA_ACCEL_CONFIG
+ */
+void MPU6050::setAccelXSelfTest(bool enabled) {
+ I2Cdev::writeBit(devAddr, MPU6050_RA_ACCEL_CONFIG, MPU6050_ACONFIG_XA_ST_BIT, enabled);
+}
+/** Get self-test enabled value for accelerometer Y axis.
+ * @return Self-test enabled value
+ * @see MPU6050_RA_ACCEL_CONFIG
+ */
+bool MPU6050::getAccelYSelfTest() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_ACCEL_CONFIG, MPU6050_ACONFIG_YA_ST_BIT, buffer);
+ return buffer[0];
+}
+/** Get self-test enabled value for accelerometer Y axis.
+ * @param enabled Self-test enabled value
+ * @see MPU6050_RA_ACCEL_CONFIG
+ */
+void MPU6050::setAccelYSelfTest(bool enabled) {
+ I2Cdev::writeBit(devAddr, MPU6050_RA_ACCEL_CONFIG, MPU6050_ACONFIG_YA_ST_BIT, enabled);
+}
+/** Get self-test enabled value for accelerometer Z axis.
+ * @return Self-test enabled value
+ * @see MPU6050_RA_ACCEL_CONFIG
+ */
+bool MPU6050::getAccelZSelfTest() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_ACCEL_CONFIG, MPU6050_ACONFIG_ZA_ST_BIT, buffer);
+ return buffer[0];
+}
+/** Set self-test enabled value for accelerometer Z axis.
+ * @param enabled Self-test enabled value
+ * @see MPU6050_RA_ACCEL_CONFIG
+ */
+void MPU6050::setAccelZSelfTest(bool enabled) {
+ I2Cdev::writeBit(devAddr, MPU6050_RA_ACCEL_CONFIG, MPU6050_ACONFIG_ZA_ST_BIT, enabled);
+}
+/** Get full-scale accelerometer range.
+ * The FS_SEL parameter allows setting the full-scale range of the accelerometer
+ * sensors, as described in the table below.
+ *
+ *
+ * 0 = +/- 2g
+ * 1 = +/- 4g
+ * 2 = +/- 8g
+ * 3 = +/- 16g
+ *
+ *
+ * @return Current full-scale accelerometer range setting
+ * @see MPU6050_ACCEL_FS_2
+ * @see MPU6050_RA_ACCEL_CONFIG
+ * @see MPU6050_ACONFIG_AFS_SEL_BIT
+ * @see MPU6050_ACONFIG_AFS_SEL_LENGTH
+ */
+uint8_t MPU6050::getFullScaleAccelRange() {
+ I2Cdev::readBits(devAddr, MPU6050_RA_ACCEL_CONFIG, MPU6050_ACONFIG_AFS_SEL_BIT, MPU6050_ACONFIG_AFS_SEL_LENGTH, buffer);
+ return buffer[0];
+}
+/** Set full-scale accelerometer range.
+ * @param range New full-scale accelerometer range setting
+ * @see getFullScaleAccelRange()
+ */
+void MPU6050::setFullScaleAccelRange(uint8_t range) {
+ I2Cdev::writeBits(devAddr, MPU6050_RA_ACCEL_CONFIG, MPU6050_ACONFIG_AFS_SEL_BIT, MPU6050_ACONFIG_AFS_SEL_LENGTH, range);
+}
+/** Get the high-pass filter configuration.
+ * The DHPF is a filter module in the path leading to motion detectors (Free
+ * Fall, Motion threshold, and Zero Motion). The high pass filter output is not
+ * available to the data registers (see Figure in Section 8 of the MPU-6000/
+ * MPU-6050 Product Specification document).
+ *
+ * The high pass filter has three modes:
+ *
+ *
+ * Reset: The filter output settles to zero within one sample. This
+ * effectively disables the high pass filter. This mode may be toggled
+ * to quickly settle the filter.
+ *
+ * On: The high pass filter will pass signals above the cut off frequency.
+ *
+ * Hold: When triggered, the filter holds the present sample. The filter
+ * output will be the difference between the input sample and the held
+ * sample.
+ *
+ *
+ *
+ * ACCEL_HPF | Filter Mode | Cut-off Frequency
+ * ----------+-------------+------------------
+ * 0 | Reset | None
+ * 1 | On | 5Hz
+ * 2 | On | 2.5Hz
+ * 3 | On | 1.25Hz
+ * 4 | On | 0.63Hz
+ * 7 | Hold | None
+ *
+ *
+ * @return Current high-pass filter configuration
+ * @see MPU6050_DHPF_RESET
+ * @see MPU6050_RA_ACCEL_CONFIG
+ */
+uint8_t MPU6050::getDHPFMode() {
+ I2Cdev::readBits(devAddr, MPU6050_RA_ACCEL_CONFIG, MPU6050_ACONFIG_ACCEL_HPF_BIT, MPU6050_ACONFIG_ACCEL_HPF_LENGTH, buffer);
+ return buffer[0];
+}
+/** Set the high-pass filter configuration.
+ * @param bandwidth New high-pass filter configuration
+ * @see setDHPFMode()
+ * @see MPU6050_DHPF_RESET
+ * @see MPU6050_RA_ACCEL_CONFIG
+ */
+void MPU6050::setDHPFMode(uint8_t bandwidth) {
+ I2Cdev::writeBits(devAddr, MPU6050_RA_ACCEL_CONFIG, MPU6050_ACONFIG_ACCEL_HPF_BIT, MPU6050_ACONFIG_ACCEL_HPF_LENGTH, bandwidth);
+}
+
+// FF_THR register
+
+/** Get free-fall event acceleration threshold.
+ * This register configures the detection threshold for Free Fall event
+ * detection. The unit of FF_THR is 1LSB = 2mg. Free Fall is detected when the
+ * absolute value of the accelerometer measurements for the three axes are each
+ * less than the detection threshold. This condition increments the Free Fall
+ * duration counter (Register 30). The Free Fall interrupt is triggered when the
+ * Free Fall duration counter reaches the time specified in FF_DUR.
+ *
+ * For more details on the Free Fall detection interrupt, see Section 8.2 of the
+ * MPU-6000/MPU-6050 Product Specification document as well as Registers 56 and
+ * 58 of this document.
+ *
+ * @return Current free-fall acceleration threshold value (LSB = 2mg)
+ * @see MPU6050_RA_FF_THR
+ */
+uint8_t MPU6050::getFreefallDetectionThreshold() {
+ I2Cdev::readByte(devAddr, MPU6050_RA_FF_THR, buffer);
+ return buffer[0];
+}
+/** Get free-fall event acceleration threshold.
+ * @param threshold New free-fall acceleration threshold value (LSB = 2mg)
+ * @see getFreefallDetectionThreshold()
+ * @see MPU6050_RA_FF_THR
+ */
+void MPU6050::setFreefallDetectionThreshold(uint8_t threshold) {
+ I2Cdev::writeByte(devAddr, MPU6050_RA_FF_THR, threshold);
+}
+
+// FF_DUR register
+
+/** Get free-fall event duration threshold.
+ * This register configures the duration counter threshold for Free Fall event
+ * detection. The duration counter ticks at 1kHz, therefore FF_DUR has a unit
+ * of 1 LSB = 1 ms.
+ *
+ * The Free Fall duration counter increments while the absolute value of the
+ * accelerometer measurements are each less than the detection threshold
+ * (Register 29). The Free Fall interrupt is triggered when the Free Fall
+ * duration counter reaches the time specified in this register.
+ *
+ * For more details on the Free Fall detection interrupt, see Section 8.2 of
+ * the MPU-6000/MPU-6050 Product Specification document as well as Registers 56
+ * and 58 of this document.
+ *
+ * @return Current free-fall duration threshold value (LSB = 1ms)
+ * @see MPU6050_RA_FF_DUR
+ */
+uint8_t MPU6050::getFreefallDetectionDuration() {
+ I2Cdev::readByte(devAddr, MPU6050_RA_FF_DUR, buffer);
+ return buffer[0];
+}
+/** Get free-fall event duration threshold.
+ * @param duration New free-fall duration threshold value (LSB = 1ms)
+ * @see getFreefallDetectionDuration()
+ * @see MPU6050_RA_FF_DUR
+ */
+void MPU6050::setFreefallDetectionDuration(uint8_t duration) {
+ I2Cdev::writeByte(devAddr, MPU6050_RA_FF_DUR, duration);
+}
+
+// MOT_THR register
+
+/** Get motion detection event acceleration threshold.
+ * This register configures the detection threshold for Motion interrupt
+ * generation. The unit of MOT_THR is 1LSB = 2mg. Motion is detected when the
+ * absolute value of any of the accelerometer measurements exceeds this Motion
+ * detection threshold. This condition increments the Motion detection duration
+ * counter (Register 32). The Motion detection interrupt is triggered when the
+ * Motion Detection counter reaches the time count specified in MOT_DUR
+ * (Register 32).
+ *
+ * The Motion interrupt will indicate the axis and polarity of detected motion
+ * in MOT_DETECT_STATUS (Register 97).
+ *
+ * For more details on the Motion detection interrupt, see Section 8.3 of the
+ * MPU-6000/MPU-6050 Product Specification document as well as Registers 56 and
+ * 58 of this document.
+ *
+ * @return Current motion detection acceleration threshold value (LSB = 2mg)
+ * @see MPU6050_RA_MOT_THR
+ */
+uint8_t MPU6050::getMotionDetectionThreshold() {
+ I2Cdev::readByte(devAddr, MPU6050_RA_MOT_THR, buffer);
+ return buffer[0];
+}
+/** Set motion detection event acceleration threshold.
+ * @param threshold New motion detection acceleration threshold value (LSB = 2mg)
+ * @see getMotionDetectionThreshold()
+ * @see MPU6050_RA_MOT_THR
+ */
+void MPU6050::setMotionDetectionThreshold(uint8_t threshold) {
+ I2Cdev::writeByte(devAddr, MPU6050_RA_MOT_THR, threshold);
+}
+
+// MOT_DUR register
+
+/** Get motion detection event duration threshold.
+ * This register configures the duration counter threshold for Motion interrupt
+ * generation. The duration counter ticks at 1 kHz, therefore MOT_DUR has a unit
+ * of 1LSB = 1ms. The Motion detection duration counter increments when the
+ * absolute value of any of the accelerometer measurements exceeds the Motion
+ * detection threshold (Register 31). The Motion detection interrupt is
+ * triggered when the Motion detection counter reaches the time count specified
+ * in this register.
+ *
+ * For more details on the Motion detection interrupt, see Section 8.3 of the
+ * MPU-6000/MPU-6050 Product Specification document.
+ *
+ * @return Current motion detection duration threshold value (LSB = 1ms)
+ * @see MPU6050_RA_MOT_DUR
+ */
+uint8_t MPU6050::getMotionDetectionDuration() {
+ I2Cdev::readByte(devAddr, MPU6050_RA_MOT_DUR, buffer);
+ return buffer[0];
+}
+/** Set motion detection event duration threshold.
+ * @param duration New motion detection duration threshold value (LSB = 1ms)
+ * @see getMotionDetectionDuration()
+ * @see MPU6050_RA_MOT_DUR
+ */
+void MPU6050::setMotionDetectionDuration(uint8_t duration) {
+ I2Cdev::writeByte(devAddr, MPU6050_RA_MOT_DUR, duration);
+}
+
+// ZRMOT_THR register
+
+/** Get zero motion detection event acceleration threshold.
+ * This register configures the detection threshold for Zero Motion interrupt
+ * generation. The unit of ZRMOT_THR is 1LSB = 2mg. Zero Motion is detected when
+ * the absolute value of the accelerometer measurements for the 3 axes are each
+ * less than the detection threshold. This condition increments the Zero Motion
+ * duration counter (Register 34). The Zero Motion interrupt is triggered when
+ * the Zero Motion duration counter reaches the time count specified in
+ * ZRMOT_DUR (Register 34).
+ *
+ * Unlike Free Fall or Motion detection, Zero Motion detection triggers an
+ * interrupt both when Zero Motion is first detected and when Zero Motion is no
+ * longer detected.
+ *
+ * When a zero motion event is detected, a Zero Motion Status will be indicated
+ * in the MOT_DETECT_STATUS register (Register 97). When a motion-to-zero-motion
+ * condition is detected, the status bit is set to 1. When a zero-motion-to-
+ * motion condition is detected, the status bit is set to 0.
+ *
+ * For more details on the Zero Motion detection interrupt, see Section 8.4 of
+ * the MPU-6000/MPU-6050 Product Specification document as well as Registers 56
+ * and 58 of this document.
+ *
+ * @return Current zero motion detection acceleration threshold value (LSB = 2mg)
+ * @see MPU6050_RA_ZRMOT_THR
+ */
+uint8_t MPU6050::getZeroMotionDetectionThreshold() {
+ I2Cdev::readByte(devAddr, MPU6050_RA_ZRMOT_THR, buffer);
+ return buffer[0];
+}
+/** Set zero motion detection event acceleration threshold.
+ * @param threshold New zero motion detection acceleration threshold value (LSB = 2mg)
+ * @see getZeroMotionDetectionThreshold()
+ * @see MPU6050_RA_ZRMOT_THR
+ */
+void MPU6050::setZeroMotionDetectionThreshold(uint8_t threshold) {
+ I2Cdev::writeByte(devAddr, MPU6050_RA_ZRMOT_THR, threshold);
+}
+
+// ZRMOT_DUR register
+
+/** Get zero motion detection event duration threshold.
+ * This register configures the duration counter threshold for Zero Motion
+ * interrupt generation. The duration counter ticks at 16 Hz, therefore
+ * ZRMOT_DUR has a unit of 1 LSB = 64 ms. The Zero Motion duration counter
+ * increments while the absolute value of the accelerometer measurements are
+ * each less than the detection threshold (Register 33). The Zero Motion
+ * interrupt is triggered when the Zero Motion duration counter reaches the time
+ * count specified in this register.
+ *
+ * For more details on the Zero Motion detection interrupt, see Section 8.4 of
+ * the MPU-6000/MPU-6050 Product Specification document, as well as Registers 56
+ * and 58 of this document.
+ *
+ * @return Current zero motion detection duration threshold value (LSB = 64ms)
+ * @see MPU6050_RA_ZRMOT_DUR
+ */
+uint8_t MPU6050::getZeroMotionDetectionDuration() {
+ I2Cdev::readByte(devAddr, MPU6050_RA_ZRMOT_DUR, buffer);
+ return buffer[0];
+}
+/** Set zero motion detection event duration threshold.
+ * @param duration New zero motion detection duration threshold value (LSB = 1ms)
+ * @see getZeroMotionDetectionDuration()
+ * @see MPU6050_RA_ZRMOT_DUR
+ */
+void MPU6050::setZeroMotionDetectionDuration(uint8_t duration) {
+ I2Cdev::writeByte(devAddr, MPU6050_RA_ZRMOT_DUR, duration);
+}
+
+// FIFO_EN register
+
+/** Get temperature FIFO enabled value.
+ * When set to 1, this bit enables TEMP_OUT_H and TEMP_OUT_L (Registers 65 and
+ * 66) to be written into the FIFO buffer.
+ * @return Current temperature FIFO enabled value
+ * @see MPU6050_RA_FIFO_EN
+ */
+bool MPU6050::getTempFIFOEnabled() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_FIFO_EN, MPU6050_TEMP_FIFO_EN_BIT, buffer);
+ return buffer[0];
+}
+/** Set temperature FIFO enabled value.
+ * @param enabled New temperature FIFO enabled value
+ * @see getTempFIFOEnabled()
+ * @see MPU6050_RA_FIFO_EN
+ */
+void MPU6050::setTempFIFOEnabled(bool enabled) {
+ I2Cdev::writeBit(devAddr, MPU6050_RA_FIFO_EN, MPU6050_TEMP_FIFO_EN_BIT, enabled);
+}
+/** Get gyroscope X-axis FIFO enabled value.
+ * When set to 1, this bit enables GYRO_XOUT_H and GYRO_XOUT_L (Registers 67 and
+ * 68) to be written into the FIFO buffer.
+ * @return Current gyroscope X-axis FIFO enabled value
+ * @see MPU6050_RA_FIFO_EN
+ */
+bool MPU6050::getXGyroFIFOEnabled() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_FIFO_EN, MPU6050_XG_FIFO_EN_BIT, buffer);
+ return buffer[0];
+}
+/** Set gyroscope X-axis FIFO enabled value.
+ * @param enabled New gyroscope X-axis FIFO enabled value
+ * @see getXGyroFIFOEnabled()
+ * @see MPU6050_RA_FIFO_EN
+ */
+void MPU6050::setXGyroFIFOEnabled(bool enabled) {
+ I2Cdev::writeBit(devAddr, MPU6050_RA_FIFO_EN, MPU6050_XG_FIFO_EN_BIT, enabled);
+}
+/** Get gyroscope Y-axis FIFO enabled value.
+ * When set to 1, this bit enables GYRO_YOUT_H and GYRO_YOUT_L (Registers 69 and
+ * 70) to be written into the FIFO buffer.
+ * @return Current gyroscope Y-axis FIFO enabled value
+ * @see MPU6050_RA_FIFO_EN
+ */
+bool MPU6050::getYGyroFIFOEnabled() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_FIFO_EN, MPU6050_YG_FIFO_EN_BIT, buffer);
+ return buffer[0];
+}
+/** Set gyroscope Y-axis FIFO enabled value.
+ * @param enabled New gyroscope Y-axis FIFO enabled value
+ * @see getYGyroFIFOEnabled()
+ * @see MPU6050_RA_FIFO_EN
+ */
+void MPU6050::setYGyroFIFOEnabled(bool enabled) {
+ I2Cdev::writeBit(devAddr, MPU6050_RA_FIFO_EN, MPU6050_YG_FIFO_EN_BIT, enabled);
+}
+/** Get gyroscope Z-axis FIFO enabled value.
+ * When set to 1, this bit enables GYRO_ZOUT_H and GYRO_ZOUT_L (Registers 71 and
+ * 72) to be written into the FIFO buffer.
+ * @return Current gyroscope Z-axis FIFO enabled value
+ * @see MPU6050_RA_FIFO_EN
+ */
+bool MPU6050::getZGyroFIFOEnabled() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_FIFO_EN, MPU6050_ZG_FIFO_EN_BIT, buffer);
+ return buffer[0];
+}
+/** Set gyroscope Z-axis FIFO enabled value.
+ * @param enabled New gyroscope Z-axis FIFO enabled value
+ * @see getZGyroFIFOEnabled()
+ * @see MPU6050_RA_FIFO_EN
+ */
+void MPU6050::setZGyroFIFOEnabled(bool enabled) {
+ I2Cdev::writeBit(devAddr, MPU6050_RA_FIFO_EN, MPU6050_ZG_FIFO_EN_BIT, enabled);
+}
+/** Get accelerometer FIFO enabled value.
+ * When set to 1, this bit enables ACCEL_XOUT_H, ACCEL_XOUT_L, ACCEL_YOUT_H,
+ * ACCEL_YOUT_L, ACCEL_ZOUT_H, and ACCEL_ZOUT_L (Registers 59 to 64) to be
+ * written into the FIFO buffer.
+ * @return Current accelerometer FIFO enabled value
+ * @see MPU6050_RA_FIFO_EN
+ */
+bool MPU6050::getAccelFIFOEnabled() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_FIFO_EN, MPU6050_ACCEL_FIFO_EN_BIT, buffer);
+ return buffer[0];
+}
+/** Set accelerometer FIFO enabled value.
+ * @param enabled New accelerometer FIFO enabled value
+ * @see getAccelFIFOEnabled()
+ * @see MPU6050_RA_FIFO_EN
+ */
+void MPU6050::setAccelFIFOEnabled(bool enabled) {
+ I2Cdev::writeBit(devAddr, MPU6050_RA_FIFO_EN, MPU6050_ACCEL_FIFO_EN_BIT, enabled);
+}
+/** Get Slave 2 FIFO enabled value.
+ * When set to 1, this bit enables EXT_SENS_DATA registers (Registers 73 to 96)
+ * associated with Slave 2 to be written into the FIFO buffer.
+ * @return Current Slave 2 FIFO enabled value
+ * @see MPU6050_RA_FIFO_EN
+ */
+bool MPU6050::getSlave2FIFOEnabled() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_FIFO_EN, MPU6050_SLV2_FIFO_EN_BIT, buffer);
+ return buffer[0];
+}
+/** Set Slave 2 FIFO enabled value.
+ * @param enabled New Slave 2 FIFO enabled value
+ * @see getSlave2FIFOEnabled()
+ * @see MPU6050_RA_FIFO_EN
+ */
+void MPU6050::setSlave2FIFOEnabled(bool enabled) {
+ I2Cdev::writeBit(devAddr, MPU6050_RA_FIFO_EN, MPU6050_SLV2_FIFO_EN_BIT, enabled);
+}
+/** Get Slave 1 FIFO enabled value.
+ * When set to 1, this bit enables EXT_SENS_DATA registers (Registers 73 to 96)
+ * associated with Slave 1 to be written into the FIFO buffer.
+ * @return Current Slave 1 FIFO enabled value
+ * @see MPU6050_RA_FIFO_EN
+ */
+bool MPU6050::getSlave1FIFOEnabled() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_FIFO_EN, MPU6050_SLV1_FIFO_EN_BIT, buffer);
+ return buffer[0];
+}
+/** Set Slave 1 FIFO enabled value.
+ * @param enabled New Slave 1 FIFO enabled value
+ * @see getSlave1FIFOEnabled()
+ * @see MPU6050_RA_FIFO_EN
+ */
+void MPU6050::setSlave1FIFOEnabled(bool enabled) {
+ I2Cdev::writeBit(devAddr, MPU6050_RA_FIFO_EN, MPU6050_SLV1_FIFO_EN_BIT, enabled);
+}
+/** Get Slave 0 FIFO enabled value.
+ * When set to 1, this bit enables EXT_SENS_DATA registers (Registers 73 to 96)
+ * associated with Slave 0 to be written into the FIFO buffer.
+ * @return Current Slave 0 FIFO enabled value
+ * @see MPU6050_RA_FIFO_EN
+ */
+bool MPU6050::getSlave0FIFOEnabled() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_FIFO_EN, MPU6050_SLV0_FIFO_EN_BIT, buffer);
+ return buffer[0];
+}
+/** Set Slave 0 FIFO enabled value.
+ * @param enabled New Slave 0 FIFO enabled value
+ * @see getSlave0FIFOEnabled()
+ * @see MPU6050_RA_FIFO_EN
+ */
+void MPU6050::setSlave0FIFOEnabled(bool enabled) {
+ I2Cdev::writeBit(devAddr, MPU6050_RA_FIFO_EN, MPU6050_SLV0_FIFO_EN_BIT, enabled);
+}
+
+// I2C_MST_CTRL register
+
+/** Get multi-master enabled value.
+ * Multi-master capability allows multiple I2C masters to operate on the same
+ * bus. In circuits where multi-master capability is required, set MULT_MST_EN
+ * to 1. This will increase current drawn by approximately 30uA.
+ *
+ * In circuits where multi-master capability is required, the state of the I2C
+ * bus must always be monitored by each separate I2C Master. Before an I2C
+ * Master can assume arbitration of the bus, it must first confirm that no other
+ * I2C Master has arbitration of the bus. When MULT_MST_EN is set to 1, the
+ * MPU-60X0's bus arbitration detection logic is turned on, enabling it to
+ * detect when the bus is available.
+ *
+ * @return Current multi-master enabled value
+ * @see MPU6050_RA_I2C_MST_CTRL
+ */
+bool MPU6050::getMultiMasterEnabled() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_I2C_MST_CTRL, MPU6050_MULT_MST_EN_BIT, buffer);
+ return buffer[0];
+}
+/** Set multi-master enabled value.
+ * @param enabled New multi-master enabled value
+ * @see getMultiMasterEnabled()
+ * @see MPU6050_RA_I2C_MST_CTRL
+ */
+void MPU6050::setMultiMasterEnabled(bool enabled) {
+ I2Cdev::writeBit(devAddr, MPU6050_RA_I2C_MST_CTRL, MPU6050_MULT_MST_EN_BIT, enabled);
+}
+/** Get wait-for-external-sensor-data enabled value.
+ * When the WAIT_FOR_ES bit is set to 1, the Data Ready interrupt will be
+ * delayed until External Sensor data from the Slave Devices are loaded into the
+ * EXT_SENS_DATA registers. This is used to ensure that both the internal sensor
+ * data (i.e. from gyro and accel) and external sensor data have been loaded to
+ * their respective data registers (i.e. the data is synced) when the Data Ready
+ * interrupt is triggered.
+ *
+ * @return Current wait-for-external-sensor-data enabled value
+ * @see MPU6050_RA_I2C_MST_CTRL
+ */
+bool MPU6050::getWaitForExternalSensorEnabled() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_I2C_MST_CTRL, MPU6050_WAIT_FOR_ES_BIT, buffer);
+ return buffer[0];
+}
+/** Set wait-for-external-sensor-data enabled value.
+ * @param enabled New wait-for-external-sensor-data enabled value
+ * @see getWaitForExternalSensorEnabled()
+ * @see MPU6050_RA_I2C_MST_CTRL
+ */
+void MPU6050::setWaitForExternalSensorEnabled(bool enabled) {
+ I2Cdev::writeBit(devAddr, MPU6050_RA_I2C_MST_CTRL, MPU6050_WAIT_FOR_ES_BIT, enabled);
+}
+/** Get Slave 3 FIFO enabled value.
+ * When set to 1, this bit enables EXT_SENS_DATA registers (Registers 73 to 96)
+ * associated with Slave 3 to be written into the FIFO buffer.
+ * @return Current Slave 3 FIFO enabled value
+ * @see MPU6050_RA_MST_CTRL
+ */
+bool MPU6050::getSlave3FIFOEnabled() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_I2C_MST_CTRL, MPU6050_SLV_3_FIFO_EN_BIT, buffer);
+ return buffer[0];
+}
+/** Set Slave 3 FIFO enabled value.
+ * @param enabled New Slave 3 FIFO enabled value
+ * @see getSlave3FIFOEnabled()
+ * @see MPU6050_RA_MST_CTRL
+ */
+void MPU6050::setSlave3FIFOEnabled(bool enabled) {
+ I2Cdev::writeBit(devAddr, MPU6050_RA_I2C_MST_CTRL, MPU6050_SLV_3_FIFO_EN_BIT, enabled);
+}
+/** Get slave read/write transition enabled value.
+ * The I2C_MST_P_NSR bit configures the I2C Master's transition from one slave
+ * read to the next slave read. If the bit equals 0, there will be a restart
+ * between reads. If the bit equals 1, there will be a stop followed by a start
+ * of the following read. When a write transaction follows a read transaction,
+ * the stop followed by a start of the successive write will be always used.
+ *
+ * @return Current slave read/write transition enabled value
+ * @see MPU6050_RA_I2C_MST_CTRL
+ */
+bool MPU6050::getSlaveReadWriteTransitionEnabled() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_I2C_MST_CTRL, MPU6050_I2C_MST_P_NSR_BIT, buffer);
+ return buffer[0];
+}
+/** Set slave read/write transition enabled value.
+ * @param enabled New slave read/write transition enabled value
+ * @see getSlaveReadWriteTransitionEnabled()
+ * @see MPU6050_RA_I2C_MST_CTRL
+ */
+void MPU6050::setSlaveReadWriteTransitionEnabled(bool enabled) {
+ I2Cdev::writeBit(devAddr, MPU6050_RA_I2C_MST_CTRL, MPU6050_I2C_MST_P_NSR_BIT, enabled);
+}
+/** Get I2C master clock speed.
+ * I2C_MST_CLK is a 4 bit unsigned value which configures a divider on the
+ * MPU-60X0 internal 8MHz clock. It sets the I2C master clock speed according to
+ * the following table:
+ *
+ *
+ * I2C_MST_CLK | I2C Master Clock Speed | 8MHz Clock Divider
+ * ------------+------------------------+-------------------
+ * 0 | 348kHz | 23
+ * 1 | 333kHz | 24
+ * 2 | 320kHz | 25
+ * 3 | 308kHz | 26
+ * 4 | 296kHz | 27
+ * 5 | 286kHz | 28
+ * 6 | 276kHz | 29
+ * 7 | 267kHz | 30
+ * 8 | 258kHz | 31
+ * 9 | 500kHz | 16
+ * 10 | 471kHz | 17
+ * 11 | 444kHz | 18
+ * 12 | 421kHz | 19
+ * 13 | 400kHz | 20
+ * 14 | 381kHz | 21
+ * 15 | 364kHz | 22
+ *
+ *
+ * @return Current I2C master clock speed
+ * @see MPU6050_RA_I2C_MST_CTRL
+ */
+uint8_t MPU6050::getMasterClockSpeed() {
+ I2Cdev::readBits(devAddr, MPU6050_RA_I2C_MST_CTRL, MPU6050_I2C_MST_CLK_BIT, MPU6050_I2C_MST_CLK_LENGTH, buffer);
+ return buffer[0];
+}
+/** Set I2C master clock speed.
+ * @reparam speed Current I2C master clock speed
+ * @see MPU6050_RA_I2C_MST_CTRL
+ */
+void MPU6050::setMasterClockSpeed(uint8_t speed) {
+ I2Cdev::writeBits(devAddr, MPU6050_RA_I2C_MST_CTRL, MPU6050_I2C_MST_CLK_BIT, MPU6050_I2C_MST_CLK_LENGTH, speed);
+}
+
+// I2C_SLV* registers (Slave 0-3)
+
+/** Get the I2C address of the specified slave (0-3).
+ * Note that Bit 7 (MSB) controls read/write mode. If Bit 7 is set, it's a read
+ * operation, and if it is cleared, then it's a write operation. The remaining
+ * bits (6-0) are the 7-bit device address of the slave device.
+ *
+ * In read mode, the result of the read is placed in the lowest available
+ * EXT_SENS_DATA register. For further information regarding the allocation of
+ * read results, please refer to the EXT_SENS_DATA register description
+ * (Registers 73 - 96).
+ *
+ * The MPU-6050 supports a total of five slaves, but Slave 4 has unique
+ * characteristics, and so it has its own functions (getSlave4* and setSlave4*).
+ *
+ * I2C data transactions are performed at the Sample Rate, as defined in
+ * Register 25. The user is responsible for ensuring that I2C data transactions
+ * to and from each enabled Slave can be completed within a single period of the
+ * Sample Rate.
+ *
+ * The I2C slave access rate can be reduced relative to the Sample Rate. This
+ * reduced access rate is determined by I2C_MST_DLY (Register 52). Whether a
+ * slave's access rate is reduced relative to the Sample Rate is determined by
+ * I2C_MST_DELAY_CTRL (Register 103).
+ *
+ * The processing order for the slaves is fixed. The sequence followed for
+ * processing the slaves is Slave 0, Slave 1, Slave 2, Slave 3 and Slave 4. If a
+ * particular Slave is disabled it will be skipped.
+ *
+ * Each slave can either be accessed at the sample rate or at a reduced sample
+ * rate. In a case where some slaves are accessed at the Sample Rate and some
+ * slaves are accessed at the reduced rate, the sequence of accessing the slaves
+ * (Slave 0 to Slave 4) is still followed. However, the reduced rate slaves will
+ * be skipped if their access rate dictates that they should not be accessed
+ * during that particular cycle. For further information regarding the reduced
+ * access rate, please refer to Register 52. Whether a slave is accessed at the
+ * Sample Rate or at the reduced rate is determined by the Delay Enable bits in
+ * Register 103.
+ *
+ * @param num Slave number (0-3)
+ * @return Current address for specified slave
+ * @see MPU6050_RA_I2C_SLV0_ADDR
+ */
+uint8_t MPU6050::getSlaveAddress(uint8_t num) {
+ if (num > 3) return 0;
+ I2Cdev::readByte(devAddr, MPU6050_RA_I2C_SLV0_ADDR + num*3, buffer);
+ return buffer[0];
+}
+/** Set the I2C address of the specified slave (0-3).
+ * @param num Slave number (0-3)
+ * @param address New address for specified slave
+ * @see getSlaveAddress()
+ * @see MPU6050_RA_I2C_SLV0_ADDR
+ */
+void MPU6050::setSlaveAddress(uint8_t num, uint8_t address) {
+ if (num > 3) return;
+ I2Cdev::writeByte(devAddr, MPU6050_RA_I2C_SLV0_ADDR + num*3, address);
+}
+/** Get the active internal register for the specified slave (0-3).
+ * Read/write operations for this slave will be done to whatever internal
+ * register address is stored in this MPU register.
+ *
+ * The MPU-6050 supports a total of five slaves, but Slave 4 has unique
+ * characteristics, and so it has its own functions.
+ *
+ * @param num Slave number (0-3)
+ * @return Current active register for specified slave
+ * @see MPU6050_RA_I2C_SLV0_REG
+ */
+uint8_t MPU6050::getSlaveRegister(uint8_t num) {
+ if (num > 3) return 0;
+ I2Cdev::readByte(devAddr, MPU6050_RA_I2C_SLV0_REG + num*3, buffer);
+ return buffer[0];
+}
+/** Set the active internal register for the specified slave (0-3).
+ * @param num Slave number (0-3)
+ * @param reg New active register for specified slave
+ * @see getSlaveRegister()
+ * @see MPU6050_RA_I2C_SLV0_REG
+ */
+void MPU6050::setSlaveRegister(uint8_t num, uint8_t reg) {
+ if (num > 3) return;
+ I2Cdev::writeByte(devAddr, MPU6050_RA_I2C_SLV0_REG + num*3, reg);
+}
+/** Get the enabled value for the specified slave (0-3).
+ * When set to 1, this bit enables Slave 0 for data transfer operations. When
+ * cleared to 0, this bit disables Slave 0 from data transfer operations.
+ * @param num Slave number (0-3)
+ * @return Current enabled value for specified slave
+ * @see MPU6050_RA_I2C_SLV0_CTRL
+ */
+bool MPU6050::getSlaveEnabled(uint8_t num) {
+ if (num > 3) return 0;
+ I2Cdev::readBit(devAddr, MPU6050_RA_I2C_SLV0_CTRL + num*3, MPU6050_I2C_SLV_EN_BIT, buffer);
+ return buffer[0];
+}
+/** Set the enabled value for the specified slave (0-3).
+ * @param num Slave number (0-3)
+ * @param enabled New enabled value for specified slave
+ * @see getSlaveEnabled()
+ * @see MPU6050_RA_I2C_SLV0_CTRL
+ */
+void MPU6050::setSlaveEnabled(uint8_t num, bool enabled) {
+ if (num > 3) return;
+ I2Cdev::writeBit(devAddr, MPU6050_RA_I2C_SLV0_CTRL + num*3, MPU6050_I2C_SLV_EN_BIT, enabled);
+}
+/** Get word pair byte-swapping enabled for the specified slave (0-3).
+ * When set to 1, this bit enables byte swapping. When byte swapping is enabled,
+ * the high and low bytes of a word pair are swapped. Please refer to
+ * I2C_SLV0_GRP for the pairing convention of the word pairs. When cleared to 0,
+ * bytes transferred to and from Slave 0 will be written to EXT_SENS_DATA
+ * registers in the order they were transferred.
+ *
+ * @param num Slave number (0-3)
+ * @return Current word pair byte-swapping enabled value for specified slave
+ * @see MPU6050_RA_I2C_SLV0_CTRL
+ */
+bool MPU6050::getSlaveWordByteSwap(uint8_t num) {
+ if (num > 3) return 0;
+ I2Cdev::readBit(devAddr, MPU6050_RA_I2C_SLV0_CTRL + num*3, MPU6050_I2C_SLV_BYTE_SW_BIT, buffer);
+ return buffer[0];
+}
+/** Set word pair byte-swapping enabled for the specified slave (0-3).
+ * @param num Slave number (0-3)
+ * @param enabled New word pair byte-swapping enabled value for specified slave
+ * @see getSlaveWordByteSwap()
+ * @see MPU6050_RA_I2C_SLV0_CTRL
+ */
+void MPU6050::setSlaveWordByteSwap(uint8_t num, bool enabled) {
+ if (num > 3) return;
+ I2Cdev::writeBit(devAddr, MPU6050_RA_I2C_SLV0_CTRL + num*3, MPU6050_I2C_SLV_BYTE_SW_BIT, enabled);
+}
+/** Get write mode for the specified slave (0-3).
+ * When set to 1, the transaction will read or write data only. When cleared to
+ * 0, the transaction will write a register address prior to reading or writing
+ * data. This should equal 0 when specifying the register address within the
+ * Slave device to/from which the ensuing data transaction will take place.
+ *
+ * @param num Slave number (0-3)
+ * @return Current write mode for specified slave (0 = register address + data, 1 = data only)
+ * @see MPU6050_RA_I2C_SLV0_CTRL
+ */
+bool MPU6050::getSlaveWriteMode(uint8_t num) {
+ if (num > 3) return 0;
+ I2Cdev::readBit(devAddr, MPU6050_RA_I2C_SLV0_CTRL + num*3, MPU6050_I2C_SLV_REG_DIS_BIT, buffer);
+ return buffer[0];
+}
+/** Set write mode for the specified slave (0-3).
+ * @param num Slave number (0-3)
+ * @param mode New write mode for specified slave (0 = register address + data, 1 = data only)
+ * @see getSlaveWriteMode()
+ * @see MPU6050_RA_I2C_SLV0_CTRL
+ */
+void MPU6050::setSlaveWriteMode(uint8_t num, bool mode) {
+ if (num > 3) return;
+ I2Cdev::writeBit(devAddr, MPU6050_RA_I2C_SLV0_CTRL + num*3, MPU6050_I2C_SLV_REG_DIS_BIT, mode);
+}
+/** Get word pair grouping order offset for the specified slave (0-3).
+ * This sets specifies the grouping order of word pairs received from registers.
+ * When cleared to 0, bytes from register addresses 0 and 1, 2 and 3, etc (even,
+ * then odd register addresses) are paired to form a word. When set to 1, bytes
+ * from register addresses are paired 1 and 2, 3 and 4, etc. (odd, then even
+ * register addresses) are paired to form a word.
+ *
+ * @param num Slave number (0-3)
+ * @return Current word pair grouping order offset for specified slave
+ * @see MPU6050_RA_I2C_SLV0_CTRL
+ */
+bool MPU6050::getSlaveWordGroupOffset(uint8_t num) {
+ if (num > 3) return 0;
+ I2Cdev::readBit(devAddr, MPU6050_RA_I2C_SLV0_CTRL + num*3, MPU6050_I2C_SLV_GRP_BIT, buffer);
+ return buffer[0];
+}
+/** Set word pair grouping order offset for the specified slave (0-3).
+ * @param num Slave number (0-3)
+ * @param enabled New word pair grouping order offset for specified slave
+ * @see getSlaveWordGroupOffset()
+ * @see MPU6050_RA_I2C_SLV0_CTRL
+ */
+void MPU6050::setSlaveWordGroupOffset(uint8_t num, bool enabled) {
+ if (num > 3) return;
+ I2Cdev::writeBit(devAddr, MPU6050_RA_I2C_SLV0_CTRL + num*3, MPU6050_I2C_SLV_GRP_BIT, enabled);
+}
+/** Get number of bytes to read for the specified slave (0-3).
+ * Specifies the number of bytes transferred to and from Slave 0. Clearing this
+ * bit to 0 is equivalent to disabling the register by writing 0 to I2C_SLV0_EN.
+ * @param num Slave number (0-3)
+ * @return Number of bytes to read for specified slave
+ * @see MPU6050_RA_I2C_SLV0_CTRL
+ */
+uint8_t MPU6050::getSlaveDataLength(uint8_t num) {
+ if (num > 3) return 0;
+ I2Cdev::readBits(devAddr, MPU6050_RA_I2C_SLV0_CTRL + num*3, MPU6050_I2C_SLV_LEN_BIT, MPU6050_I2C_SLV_LEN_LENGTH, buffer);
+ return buffer[0];
+}
+/** Set number of bytes to read for the specified slave (0-3).
+ * @param num Slave number (0-3)
+ * @param length Number of bytes to read for specified slave
+ * @see getSlaveDataLength()
+ * @see MPU6050_RA_I2C_SLV0_CTRL
+ */
+void MPU6050::setSlaveDataLength(uint8_t num, uint8_t length) {
+ if (num > 3) return;
+ I2Cdev::writeBits(devAddr, MPU6050_RA_I2C_SLV0_CTRL + num*3, MPU6050_I2C_SLV_LEN_BIT, MPU6050_I2C_SLV_LEN_LENGTH, length);
+}
+
+// I2C_SLV* registers (Slave 4)
+
+/** Get the I2C address of Slave 4.
+ * Note that Bit 7 (MSB) controls read/write mode. If Bit 7 is set, it's a read
+ * operation, and if it is cleared, then it's a write operation. The remaining
+ * bits (6-0) are the 7-bit device address of the slave device.
+ *
+ * @return Current address for Slave 4
+ * @see getSlaveAddress()
+ * @see MPU6050_RA_I2C_SLV4_ADDR
+ */
+uint8_t MPU6050::getSlave4Address() {
+ I2Cdev::readByte(devAddr, MPU6050_RA_I2C_SLV4_ADDR, buffer);
+ return buffer[0];
+}
+/** Set the I2C address of Slave 4.
+ * @param address New address for Slave 4
+ * @see getSlave4Address()
+ * @see MPU6050_RA_I2C_SLV4_ADDR
+ */
+void MPU6050::setSlave4Address(uint8_t address) {
+ I2Cdev::writeByte(devAddr, MPU6050_RA_I2C_SLV4_ADDR, address);
+}
+/** Get the active internal register for the Slave 4.
+ * Read/write operations for this slave will be done to whatever internal
+ * register address is stored in this MPU register.
+ *
+ * @return Current active register for Slave 4
+ * @see MPU6050_RA_I2C_SLV4_REG
+ */
+uint8_t MPU6050::getSlave4Register() {
+ I2Cdev::readByte(devAddr, MPU6050_RA_I2C_SLV4_REG, buffer);
+ return buffer[0];
+}
+/** Set the active internal register for Slave 4.
+ * @param reg New active register for Slave 4
+ * @see getSlave4Register()
+ * @see MPU6050_RA_I2C_SLV4_REG
+ */
+void MPU6050::setSlave4Register(uint8_t reg) {
+ I2Cdev::writeByte(devAddr, MPU6050_RA_I2C_SLV4_REG, reg);
+}
+/** Set new byte to write to Slave 4.
+ * This register stores the data to be written into the Slave 4. If I2C_SLV4_RW
+ * is set 1 (set to read), this register has no effect.
+ * @param data New byte to write to Slave 4
+ * @see MPU6050_RA_I2C_SLV4_DO
+ */
+void MPU6050::setSlave4OutputByte(uint8_t data) {
+ I2Cdev::writeByte(devAddr, MPU6050_RA_I2C_SLV4_DO, data);
+}
+/** Get the enabled value for the Slave 4.
+ * When set to 1, this bit enables Slave 4 for data transfer operations. When
+ * cleared to 0, this bit disables Slave 4 from data transfer operations.
+ * @return Current enabled value for Slave 4
+ * @see MPU6050_RA_I2C_SLV4_CTRL
+ */
+bool MPU6050::getSlave4Enabled() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_I2C_SLV4_CTRL, MPU6050_I2C_SLV4_EN_BIT, buffer);
+ return buffer[0];
+}
+/** Set the enabled value for Slave 4.
+ * @param enabled New enabled value for Slave 4
+ * @see getSlave4Enabled()
+ * @see MPU6050_RA_I2C_SLV4_CTRL
+ */
+void MPU6050::setSlave4Enabled(bool enabled) {
+ I2Cdev::writeBit(devAddr, MPU6050_RA_I2C_SLV4_CTRL, MPU6050_I2C_SLV4_EN_BIT, enabled);
+}
+/** Get the enabled value for Slave 4 transaction interrupts.
+ * When set to 1, this bit enables the generation of an interrupt signal upon
+ * completion of a Slave 4 transaction. When cleared to 0, this bit disables the
+ * generation of an interrupt signal upon completion of a Slave 4 transaction.
+ * The interrupt status can be observed in Register 54.
+ *
+ * @return Current enabled value for Slave 4 transaction interrupts.
+ * @see MPU6050_RA_I2C_SLV4_CTRL
+ */
+bool MPU6050::getSlave4InterruptEnabled() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_I2C_SLV4_CTRL, MPU6050_I2C_SLV4_INT_EN_BIT, buffer);
+ return buffer[0];
+}
+/** Set the enabled value for Slave 4 transaction interrupts.
+ * @param enabled New enabled value for Slave 4 transaction interrupts.
+ * @see getSlave4InterruptEnabled()
+ * @see MPU6050_RA_I2C_SLV4_CTRL
+ */
+void MPU6050::setSlave4InterruptEnabled(bool enabled) {
+ I2Cdev::writeBit(devAddr, MPU6050_RA_I2C_SLV4_CTRL, MPU6050_I2C_SLV4_INT_EN_BIT, enabled);
+}
+/** Get write mode for Slave 4.
+ * When set to 1, the transaction will read or write data only. When cleared to
+ * 0, the transaction will write a register address prior to reading or writing
+ * data. This should equal 0 when specifying the register address within the
+ * Slave device to/from which the ensuing data transaction will take place.
+ *
+ * @return Current write mode for Slave 4 (0 = register address + data, 1 = data only)
+ * @see MPU6050_RA_I2C_SLV4_CTRL
+ */
+bool MPU6050::getSlave4WriteMode() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_I2C_SLV4_CTRL, MPU6050_I2C_SLV4_REG_DIS_BIT, buffer);
+ return buffer[0];
+}
+/** Set write mode for the Slave 4.
+ * @param mode New write mode for Slave 4 (0 = register address + data, 1 = data only)
+ * @see getSlave4WriteMode()
+ * @see MPU6050_RA_I2C_SLV4_CTRL
+ */
+void MPU6050::setSlave4WriteMode(bool mode) {
+ I2Cdev::writeBit(devAddr, MPU6050_RA_I2C_SLV4_CTRL, MPU6050_I2C_SLV4_REG_DIS_BIT, mode);
+}
+/** Get Slave 4 master delay value.
+ * This configures the reduced access rate of I2C slaves relative to the Sample
+ * Rate. When a slave's access rate is decreased relative to the Sample Rate,
+ * the slave is accessed every:
+ *
+ * 1 / (1 + I2C_MST_DLY) samples
+ *
+ * This base Sample Rate in turn is determined by SMPLRT_DIV (register 25) and
+ * DLPF_CFG (register 26). Whether a slave's access rate is reduced relative to
+ * the Sample Rate is determined by I2C_MST_DELAY_CTRL (register 103). For
+ * further information regarding the Sample Rate, please refer to register 25.
+ *
+ * @return Current Slave 4 master delay value
+ * @see MPU6050_RA_I2C_SLV4_CTRL
+ */
+uint8_t MPU6050::getSlave4MasterDelay() {
+ I2Cdev::readBits(devAddr, MPU6050_RA_I2C_SLV4_CTRL, MPU6050_I2C_SLV4_MST_DLY_BIT, MPU6050_I2C_SLV4_MST_DLY_LENGTH, buffer);
+ return buffer[0];
+}
+/** Set Slave 4 master delay value.
+ * @param delay New Slave 4 master delay value
+ * @see getSlave4MasterDelay()
+ * @see MPU6050_RA_I2C_SLV4_CTRL
+ */
+void MPU6050::setSlave4MasterDelay(uint8_t delay) {
+ I2Cdev::writeBits(devAddr, MPU6050_RA_I2C_SLV4_CTRL, MPU6050_I2C_SLV4_MST_DLY_BIT, MPU6050_I2C_SLV4_MST_DLY_LENGTH, delay);
+}
+/** Get last available byte read from Slave 4.
+ * This register stores the data read from Slave 4. This field is populated
+ * after a read transaction.
+ * @return Last available byte read from to Slave 4
+ * @see MPU6050_RA_I2C_SLV4_DI
+ */
+uint8_t MPU6050::getSlate4InputByte() {
+ I2Cdev::readByte(devAddr, MPU6050_RA_I2C_SLV4_DI, buffer);
+ return buffer[0];
+}
+
+// I2C_MST_STATUS register
+
+/** Get FSYNC interrupt status.
+ * This bit reflects the status of the FSYNC interrupt from an external device
+ * into the MPU-60X0. This is used as a way to pass an external interrupt
+ * through the MPU-60X0 to the host application processor. When set to 1, this
+ * bit will cause an interrupt if FSYNC_INT_EN is asserted in INT_PIN_CFG
+ * (Register 55).
+ * @return FSYNC interrupt status
+ * @see MPU6050_RA_I2C_MST_STATUS
+ */
+bool MPU6050::getPassthroughStatus() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_I2C_MST_STATUS, MPU6050_MST_PASS_THROUGH_BIT, buffer);
+ return buffer[0];
+}
+/** Get Slave 4 transaction done status.
+ * Automatically sets to 1 when a Slave 4 transaction has completed. This
+ * triggers an interrupt if the I2C_MST_INT_EN bit in the INT_ENABLE register
+ * (Register 56) is asserted and if the SLV_4_DONE_INT bit is asserted in the
+ * I2C_SLV4_CTRL register (Register 52).
+ * @return Slave 4 transaction done status
+ * @see MPU6050_RA_I2C_MST_STATUS
+ */
+bool MPU6050::getSlave4IsDone() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_I2C_MST_STATUS, MPU6050_MST_I2C_SLV4_DONE_BIT, buffer);
+ return buffer[0];
+}
+/** Get master arbitration lost status.
+ * This bit automatically sets to 1 when the I2C Master has lost arbitration of
+ * the auxiliary I2C bus (an error condition). This triggers an interrupt if the
+ * I2C_MST_INT_EN bit in the INT_ENABLE register (Register 56) is asserted.
+ * @return Master arbitration lost status
+ * @see MPU6050_RA_I2C_MST_STATUS
+ */
+bool MPU6050::getLostArbitration() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_I2C_MST_STATUS, MPU6050_MST_I2C_LOST_ARB_BIT, buffer);
+ return buffer[0];
+}
+/** Get Slave 4 NACK status.
+ * This bit automatically sets to 1 when the I2C Master receives a NACK in a
+ * transaction with Slave 4. This triggers an interrupt if the I2C_MST_INT_EN
+ * bit in the INT_ENABLE register (Register 56) is asserted.
+ * @return Slave 4 NACK interrupt status
+ * @see MPU6050_RA_I2C_MST_STATUS
+ */
+bool MPU6050::getSlave4Nack() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_I2C_MST_STATUS, MPU6050_MST_I2C_SLV4_NACK_BIT, buffer);
+ return buffer[0];
+}
+/** Get Slave 3 NACK status.
+ * This bit automatically sets to 1 when the I2C Master receives a NACK in a
+ * transaction with Slave 3. This triggers an interrupt if the I2C_MST_INT_EN
+ * bit in the INT_ENABLE register (Register 56) is asserted.
+ * @return Slave 3 NACK interrupt status
+ * @see MPU6050_RA_I2C_MST_STATUS
+ */
+bool MPU6050::getSlave3Nack() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_I2C_MST_STATUS, MPU6050_MST_I2C_SLV3_NACK_BIT, buffer);
+ return buffer[0];
+}
+/** Get Slave 2 NACK status.
+ * This bit automatically sets to 1 when the I2C Master receives a NACK in a
+ * transaction with Slave 2. This triggers an interrupt if the I2C_MST_INT_EN
+ * bit in the INT_ENABLE register (Register 56) is asserted.
+ * @return Slave 2 NACK interrupt status
+ * @see MPU6050_RA_I2C_MST_STATUS
+ */
+bool MPU6050::getSlave2Nack() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_I2C_MST_STATUS, MPU6050_MST_I2C_SLV2_NACK_BIT, buffer);
+ return buffer[0];
+}
+/** Get Slave 1 NACK status.
+ * This bit automatically sets to 1 when the I2C Master receives a NACK in a
+ * transaction with Slave 1. This triggers an interrupt if the I2C_MST_INT_EN
+ * bit in the INT_ENABLE register (Register 56) is asserted.
+ * @return Slave 1 NACK interrupt status
+ * @see MPU6050_RA_I2C_MST_STATUS
+ */
+bool MPU6050::getSlave1Nack() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_I2C_MST_STATUS, MPU6050_MST_I2C_SLV1_NACK_BIT, buffer);
+ return buffer[0];
+}
+/** Get Slave 0 NACK status.
+ * This bit automatically sets to 1 when the I2C Master receives a NACK in a
+ * transaction with Slave 0. This triggers an interrupt if the I2C_MST_INT_EN
+ * bit in the INT_ENABLE register (Register 56) is asserted.
+ * @return Slave 0 NACK interrupt status
+ * @see MPU6050_RA_I2C_MST_STATUS
+ */
+bool MPU6050::getSlave0Nack() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_I2C_MST_STATUS, MPU6050_MST_I2C_SLV0_NACK_BIT, buffer);
+ return buffer[0];
+}
+
+// INT_PIN_CFG register
+
+/** Get interrupt logic level mode.
+ * Will be set 0 for active-high, 1 for active-low.
+ * @return Current interrupt mode (0=active-high, 1=active-low)
+ * @see MPU6050_RA_INT_PIN_CFG
+ * @see MPU6050_INTCFG_INT_LEVEL_BIT
+ */
+bool MPU6050::getInterruptMode() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_INT_PIN_CFG, MPU6050_INTCFG_INT_LEVEL_BIT, buffer);
+ return buffer[0];
+}
+/** Set interrupt logic level mode.
+ * @param mode New interrupt mode (0=active-high, 1=active-low)
+ * @see getInterruptMode()
+ * @see MPU6050_RA_INT_PIN_CFG
+ * @see MPU6050_INTCFG_INT_LEVEL_BIT
+ */
+void MPU6050::setInterruptMode(bool mode) {
+ I2Cdev::writeBit(devAddr, MPU6050_RA_INT_PIN_CFG, MPU6050_INTCFG_INT_LEVEL_BIT, mode);
+}
+/** Get interrupt drive mode.
+ * Will be set 0 for push-pull, 1 for open-drain.
+ * @return Current interrupt drive mode (0=push-pull, 1=open-drain)
+ * @see MPU6050_RA_INT_PIN_CFG
+ * @see MPU6050_INTCFG_INT_OPEN_BIT
+ */
+bool MPU6050::getInterruptDrive() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_INT_PIN_CFG, MPU6050_INTCFG_INT_OPEN_BIT, buffer);
+ return buffer[0];
+}
+/** Set interrupt drive mode.
+ * @param drive New interrupt drive mode (0=push-pull, 1=open-drain)
+ * @see getInterruptDrive()
+ * @see MPU6050_RA_INT_PIN_CFG
+ * @see MPU6050_INTCFG_INT_OPEN_BIT
+ */
+void MPU6050::setInterruptDrive(bool drive) {
+ I2Cdev::writeBit(devAddr, MPU6050_RA_INT_PIN_CFG, MPU6050_INTCFG_INT_OPEN_BIT, drive);
+}
+/** Get interrupt latch mode.
+ * Will be set 0 for 50us-pulse, 1 for latch-until-int-cleared.
+ * @return Current latch mode (0=50us-pulse, 1=latch-until-int-cleared)
+ * @see MPU6050_RA_INT_PIN_CFG
+ * @see MPU6050_INTCFG_LATCH_INT_EN_BIT
+ */
+bool MPU6050::getInterruptLatch() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_INT_PIN_CFG, MPU6050_INTCFG_LATCH_INT_EN_BIT, buffer);
+ return buffer[0];
+}
+/** Set interrupt latch mode.
+ * @param latch New latch mode (0=50us-pulse, 1=latch-until-int-cleared)
+ * @see getInterruptLatch()
+ * @see MPU6050_RA_INT_PIN_CFG
+ * @see MPU6050_INTCFG_LATCH_INT_EN_BIT
+ */
+void MPU6050::setInterruptLatch(bool latch) {
+ I2Cdev::writeBit(devAddr, MPU6050_RA_INT_PIN_CFG, MPU6050_INTCFG_LATCH_INT_EN_BIT, latch);
+}
+/** Get interrupt latch clear mode.
+ * Will be set 0 for status-read-only, 1 for any-register-read.
+ * @return Current latch clear mode (0=status-read-only, 1=any-register-read)
+ * @see MPU6050_RA_INT_PIN_CFG
+ * @see MPU6050_INTCFG_INT_RD_CLEAR_BIT
+ */
+bool MPU6050::getInterruptLatchClear() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_INT_PIN_CFG, MPU6050_INTCFG_INT_RD_CLEAR_BIT, buffer);
+ return buffer[0];
+}
+/** Set interrupt latch clear mode.
+ * @param clear New latch clear mode (0=status-read-only, 1=any-register-read)
+ * @see getInterruptLatchClear()
+ * @see MPU6050_RA_INT_PIN_CFG
+ * @see MPU6050_INTCFG_INT_RD_CLEAR_BIT
+ */
+void MPU6050::setInterruptLatchClear(bool clear) {
+ I2Cdev::writeBit(devAddr, MPU6050_RA_INT_PIN_CFG, MPU6050_INTCFG_INT_RD_CLEAR_BIT, clear);
+}
+/** Get FSYNC interrupt logic level mode.
+ * @return Current FSYNC interrupt mode (0=active-high, 1=active-low)
+ * @see getFSyncInterruptMode()
+ * @see MPU6050_RA_INT_PIN_CFG
+ * @see MPU6050_INTCFG_FSYNC_INT_LEVEL_BIT
+ */
+bool MPU6050::getFSyncInterruptLevel() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_INT_PIN_CFG, MPU6050_INTCFG_FSYNC_INT_LEVEL_BIT, buffer);
+ return buffer[0];
+}
+/** Set FSYNC interrupt logic level mode.
+ * @param mode New FSYNC interrupt mode (0=active-high, 1=active-low)
+ * @see getFSyncInterruptMode()
+ * @see MPU6050_RA_INT_PIN_CFG
+ * @see MPU6050_INTCFG_FSYNC_INT_LEVEL_BIT
+ */
+void MPU6050::setFSyncInterruptLevel(bool level) {
+ I2Cdev::writeBit(devAddr, MPU6050_RA_INT_PIN_CFG, MPU6050_INTCFG_FSYNC_INT_LEVEL_BIT, level);
+}
+/** Get FSYNC pin interrupt enabled setting.
+ * Will be set 0 for disabled, 1 for enabled.
+ * @return Current interrupt enabled setting
+ * @see MPU6050_RA_INT_PIN_CFG
+ * @see MPU6050_INTCFG_FSYNC_INT_EN_BIT
+ */
+bool MPU6050::getFSyncInterruptEnabled() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_INT_PIN_CFG, MPU6050_INTCFG_FSYNC_INT_EN_BIT, buffer);
+ return buffer[0];
+}
+/** Set FSYNC pin interrupt enabled setting.
+ * @param enabled New FSYNC pin interrupt enabled setting
+ * @see getFSyncInterruptEnabled()
+ * @see MPU6050_RA_INT_PIN_CFG
+ * @see MPU6050_INTCFG_FSYNC_INT_EN_BIT
+ */
+void MPU6050::setFSyncInterruptEnabled(bool enabled) {
+ I2Cdev::writeBit(devAddr, MPU6050_RA_INT_PIN_CFG, MPU6050_INTCFG_FSYNC_INT_EN_BIT, enabled);
+}
+/** Get I2C bypass enabled status.
+ * When this bit is equal to 1 and I2C_MST_EN (Register 106 bit[5]) is equal to
+ * 0, the host application processor will be able to directly access the
+ * auxiliary I2C bus of the MPU-60X0. When this bit is equal to 0, the host
+ * application processor will not be able to directly access the auxiliary I2C
+ * bus of the MPU-60X0 regardless of the state of I2C_MST_EN (Register 106
+ * bit[5]).
+ * @return Current I2C bypass enabled status
+ * @see MPU6050_RA_INT_PIN_CFG
+ * @see MPU6050_INTCFG_I2C_BYPASS_EN_BIT
+ */
+bool MPU6050::getI2CBypassEnabled() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_INT_PIN_CFG, MPU6050_INTCFG_I2C_BYPASS_EN_BIT, buffer);
+ return buffer[0];
+}
+/** Set I2C bypass enabled status.
+ * When this bit is equal to 1 and I2C_MST_EN (Register 106 bit[5]) is equal to
+ * 0, the host application processor will be able to directly access the
+ * auxiliary I2C bus of the MPU-60X0. When this bit is equal to 0, the host
+ * application processor will not be able to directly access the auxiliary I2C
+ * bus of the MPU-60X0 regardless of the state of I2C_MST_EN (Register 106
+ * bit[5]).
+ * @param enabled New I2C bypass enabled status
+ * @see MPU6050_RA_INT_PIN_CFG
+ * @see MPU6050_INTCFG_I2C_BYPASS_EN_BIT
+ */
+void MPU6050::setI2CBypassEnabled(bool enabled) {
+ I2Cdev::writeBit(devAddr, MPU6050_RA_INT_PIN_CFG, MPU6050_INTCFG_I2C_BYPASS_EN_BIT, enabled);
+}
+/** Get reference clock output enabled status.
+ * When this bit is equal to 1, a reference clock output is provided at the
+ * CLKOUT pin. When this bit is equal to 0, the clock output is disabled. For
+ * further information regarding CLKOUT, please refer to the MPU-60X0 Product
+ * Specification document.
+ * @return Current reference clock output enabled status
+ * @see MPU6050_RA_INT_PIN_CFG
+ * @see MPU6050_INTCFG_CLKOUT_EN_BIT
+ */
+bool MPU6050::getClockOutputEnabled() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_INT_PIN_CFG, MPU6050_INTCFG_CLKOUT_EN_BIT, buffer);
+ return buffer[0];
+}
+/** Set reference clock output enabled status.
+ * When this bit is equal to 1, a reference clock output is provided at the
+ * CLKOUT pin. When this bit is equal to 0, the clock output is disabled. For
+ * further information regarding CLKOUT, please refer to the MPU-60X0 Product
+ * Specification document.
+ * @param enabled New reference clock output enabled status
+ * @see MPU6050_RA_INT_PIN_CFG
+ * @see MPU6050_INTCFG_CLKOUT_EN_BIT
+ */
+void MPU6050::setClockOutputEnabled(bool enabled) {
+ I2Cdev::writeBit(devAddr, MPU6050_RA_INT_PIN_CFG, MPU6050_INTCFG_CLKOUT_EN_BIT, enabled);
+}
+
+// INT_ENABLE register
+
+/** Get full interrupt enabled status.
+ * Full register byte for all interrupts, for quick reading. Each bit will be
+ * set 0 for disabled, 1 for enabled.
+ * @return Current interrupt enabled status
+ * @see MPU6050_RA_INT_ENABLE
+ * @see MPU6050_INTERRUPT_FF_BIT
+ **/
+uint8_t MPU6050::getIntEnabled() {
+ I2Cdev::readByte(devAddr, MPU6050_RA_INT_ENABLE, buffer);
+ return buffer[0];
+}
+/** Set full interrupt enabled status.
+ * Full register byte for all interrupts, for quick reading. Each bit should be
+ * set 0 for disabled, 1 for enabled.
+ * @param enabled New interrupt enabled status
+ * @see getIntFreefallEnabled()
+ * @see MPU6050_RA_INT_ENABLE
+ * @see MPU6050_INTERRUPT_FF_BIT
+ **/
+void MPU6050::setIntEnabled(uint8_t enabled) {
+ I2Cdev::writeByte(devAddr, MPU6050_RA_INT_ENABLE, enabled);
+}
+/** Get Free Fall interrupt enabled status.
+ * Will be set 0 for disabled, 1 for enabled.
+ * @return Current interrupt enabled status
+ * @see MPU6050_RA_INT_ENABLE
+ * @see MPU6050_INTERRUPT_FF_BIT
+ **/
+bool MPU6050::getIntFreefallEnabled() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_INT_ENABLE, MPU6050_INTERRUPT_FF_BIT, buffer);
+ return buffer[0];
+}
+/** Set Free Fall interrupt enabled status.
+ * @param enabled New interrupt enabled status
+ * @see getIntFreefallEnabled()
+ * @see MPU6050_RA_INT_ENABLE
+ * @see MPU6050_INTERRUPT_FF_BIT
+ **/
+void MPU6050::setIntFreefallEnabled(bool enabled) {
+ I2Cdev::writeBit(devAddr, MPU6050_RA_INT_ENABLE, MPU6050_INTERRUPT_FF_BIT, enabled);
+}
+/** Get Motion Detection interrupt enabled status.
+ * Will be set 0 for disabled, 1 for enabled.
+ * @return Current interrupt enabled status
+ * @see MPU6050_RA_INT_ENABLE
+ * @see MPU6050_INTERRUPT_MOT_BIT
+ **/
+bool MPU6050::getIntMotionEnabled() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_INT_ENABLE, MPU6050_INTERRUPT_MOT_BIT, buffer);
+ return buffer[0];
+}
+/** Set Motion Detection interrupt enabled status.
+ * @param enabled New interrupt enabled status
+ * @see getIntMotionEnabled()
+ * @see MPU6050_RA_INT_ENABLE
+ * @see MPU6050_INTERRUPT_MOT_BIT
+ **/
+void MPU6050::setIntMotionEnabled(bool enabled) {
+ I2Cdev::writeBit(devAddr, MPU6050_RA_INT_ENABLE, MPU6050_INTERRUPT_MOT_BIT, enabled);
+}
+/** Get Zero Motion Detection interrupt enabled status.
+ * Will be set 0 for disabled, 1 for enabled.
+ * @return Current interrupt enabled status
+ * @see MPU6050_RA_INT_ENABLE
+ * @see MPU6050_INTERRUPT_ZMOT_BIT
+ **/
+bool MPU6050::getIntZeroMotionEnabled() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_INT_ENABLE, MPU6050_INTERRUPT_ZMOT_BIT, buffer);
+ return buffer[0];
+}
+/** Set Zero Motion Detection interrupt enabled status.
+ * @param enabled New interrupt enabled status
+ * @see getIntZeroMotionEnabled()
+ * @see MPU6050_RA_INT_ENABLE
+ * @see MPU6050_INTERRUPT_ZMOT_BIT
+ **/
+void MPU6050::setIntZeroMotionEnabled(bool enabled) {
+ I2Cdev::writeBit(devAddr, MPU6050_RA_INT_ENABLE, MPU6050_INTERRUPT_ZMOT_BIT, enabled);
+}
+/** Get FIFO Buffer Overflow interrupt enabled status.
+ * Will be set 0 for disabled, 1 for enabled.
+ * @return Current interrupt enabled status
+ * @see MPU6050_RA_INT_ENABLE
+ * @see MPU6050_INTERRUPT_FIFO_OFLOW_BIT
+ **/
+bool MPU6050::getIntFIFOBufferOverflowEnabled() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_INT_ENABLE, MPU6050_INTERRUPT_FIFO_OFLOW_BIT, buffer);
+ return buffer[0];
+}
+/** Set FIFO Buffer Overflow interrupt enabled status.
+ * @param enabled New interrupt enabled status
+ * @see getIntFIFOBufferOverflowEnabled()
+ * @see MPU6050_RA_INT_ENABLE
+ * @see MPU6050_INTERRUPT_FIFO_OFLOW_BIT
+ **/
+void MPU6050::setIntFIFOBufferOverflowEnabled(bool enabled) {
+ I2Cdev::writeBit(devAddr, MPU6050_RA_INT_ENABLE, MPU6050_INTERRUPT_FIFO_OFLOW_BIT, enabled);
+}
+/** Get I2C Master interrupt enabled status.
+ * This enables any of the I2C Master interrupt sources to generate an
+ * interrupt. Will be set 0 for disabled, 1 for enabled.
+ * @return Current interrupt enabled status
+ * @see MPU6050_RA_INT_ENABLE
+ * @see MPU6050_INTERRUPT_I2C_MST_INT_BIT
+ **/
+bool MPU6050::getIntI2CMasterEnabled() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_INT_ENABLE, MPU6050_INTERRUPT_I2C_MST_INT_BIT, buffer);
+ return buffer[0];
+}
+/** Set I2C Master interrupt enabled status.
+ * @param enabled New interrupt enabled status
+ * @see getIntI2CMasterEnabled()
+ * @see MPU6050_RA_INT_ENABLE
+ * @see MPU6050_INTERRUPT_I2C_MST_INT_BIT
+ **/
+void MPU6050::setIntI2CMasterEnabled(bool enabled) {
+ I2Cdev::writeBit(devAddr, MPU6050_RA_INT_ENABLE, MPU6050_INTERRUPT_I2C_MST_INT_BIT, enabled);
+}
+/** Get Data Ready interrupt enabled setting.
+ * This event occurs each time a write operation to all of the sensor registers
+ * has been completed. Will be set 0 for disabled, 1 for enabled.
+ * @return Current interrupt enabled status
+ * @see MPU6050_RA_INT_ENABLE
+ * @see MPU6050_INTERRUPT_DATA_RDY_BIT
+ */
+bool MPU6050::getIntDataReadyEnabled() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_INT_ENABLE, MPU6050_INTERRUPT_DATA_RDY_BIT, buffer);
+ return buffer[0];
+}
+/** Set Data Ready interrupt enabled status.
+ * @param enabled New interrupt enabled status
+ * @see getIntDataReadyEnabled()
+ * @see MPU6050_RA_INT_CFG
+ * @see MPU6050_INTERRUPT_DATA_RDY_BIT
+ */
+void MPU6050::setIntDataReadyEnabled(bool enabled) {
+ I2Cdev::writeBit(devAddr, MPU6050_RA_INT_ENABLE, MPU6050_INTERRUPT_DATA_RDY_BIT, enabled);
+}
+
+// INT_STATUS register
+
+/** Get full set of interrupt status bits.
+ * These bits clear to 0 after the register has been read. Very useful
+ * for getting multiple INT statuses, since each single bit read clears
+ * all of them because it has to read the whole byte.
+ * @return Current interrupt status
+ * @see MPU6050_RA_INT_STATUS
+ */
+uint8_t MPU6050::getIntStatus() {
+ I2Cdev::readByte(devAddr, MPU6050_RA_INT_STATUS, buffer);
+ return buffer[0];
+}
+/** Get Free Fall interrupt status.
+ * This bit automatically sets to 1 when a Free Fall interrupt has been
+ * generated. The bit clears to 0 after the register has been read.
+ * @return Current interrupt status
+ * @see MPU6050_RA_INT_STATUS
+ * @see MPU6050_INTERRUPT_FF_BIT
+ */
+bool MPU6050::getIntFreefallStatus() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_INT_STATUS, MPU6050_INTERRUPT_FF_BIT, buffer);
+ return buffer[0];
+}
+/** Get Motion Detection interrupt status.
+ * This bit automatically sets to 1 when a Motion Detection interrupt has been
+ * generated. The bit clears to 0 after the register has been read.
+ * @return Current interrupt status
+ * @see MPU6050_RA_INT_STATUS
+ * @see MPU6050_INTERRUPT_MOT_BIT
+ */
+bool MPU6050::getIntMotionStatus() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_INT_STATUS, MPU6050_INTERRUPT_MOT_BIT, buffer);
+ return buffer[0];
+}
+/** Get Zero Motion Detection interrupt status.
+ * This bit automatically sets to 1 when a Zero Motion Detection interrupt has
+ * been generated. The bit clears to 0 after the register has been read.
+ * @return Current interrupt status
+ * @see MPU6050_RA_INT_STATUS
+ * @see MPU6050_INTERRUPT_ZMOT_BIT
+ */
+bool MPU6050::getIntZeroMotionStatus() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_INT_STATUS, MPU6050_INTERRUPT_ZMOT_BIT, buffer);
+ return buffer[0];
+}
+/** Get FIFO Buffer Overflow interrupt status.
+ * This bit automatically sets to 1 when a Free Fall interrupt has been
+ * generated. The bit clears to 0 after the register has been read.
+ * @return Current interrupt status
+ * @see MPU6050_RA_INT_STATUS
+ * @see MPU6050_INTERRUPT_FIFO_OFLOW_BIT
+ */
+bool MPU6050::getIntFIFOBufferOverflowStatus() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_INT_STATUS, MPU6050_INTERRUPT_FIFO_OFLOW_BIT, buffer);
+ return buffer[0];
+}
+/** Get I2C Master interrupt status.
+ * This bit automatically sets to 1 when an I2C Master interrupt has been
+ * generated. For a list of I2C Master interrupts, please refer to Register 54.
+ * The bit clears to 0 after the register has been read.
+ * @return Current interrupt status
+ * @see MPU6050_RA_INT_STATUS
+ * @see MPU6050_INTERRUPT_I2C_MST_INT_BIT
+ */
+bool MPU6050::getIntI2CMasterStatus() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_INT_STATUS, MPU6050_INTERRUPT_I2C_MST_INT_BIT, buffer);
+ return buffer[0];
+}
+/** Get Data Ready interrupt status.
+ * This bit automatically sets to 1 when a Data Ready interrupt has been
+ * generated. The bit clears to 0 after the register has been read.
+ * @return Current interrupt status
+ * @see MPU6050_RA_INT_STATUS
+ * @see MPU6050_INTERRUPT_DATA_RDY_BIT
+ */
+bool MPU6050::getIntDataReadyStatus() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_INT_STATUS, MPU6050_INTERRUPT_DATA_RDY_BIT, buffer);
+ return buffer[0];
+}
+
+// ACCEL_*OUT_* registers
+
+/** Get raw 9-axis motion sensor readings (accel/gyro/compass).
+ * FUNCTION NOT FULLY IMPLEMENTED YET.
+ * @param ax 16-bit signed integer container for accelerometer X-axis value
+ * @param ay 16-bit signed integer container for accelerometer Y-axis value
+ * @param az 16-bit signed integer container for accelerometer Z-axis value
+ * @param gx 16-bit signed integer container for gyroscope X-axis value
+ * @param gy 16-bit signed integer container for gyroscope Y-axis value
+ * @param gz 16-bit signed integer container for gyroscope Z-axis value
+ * @param mx 16-bit signed integer container for magnetometer X-axis value
+ * @param my 16-bit signed integer container for magnetometer Y-axis value
+ * @param mz 16-bit signed integer container for magnetometer Z-axis value
+ * @see getMotion6()
+ * @see getAcceleration()
+ * @see getRotation()
+ * @see MPU6050_RA_ACCEL_XOUT_H
+ */
+void MPU6050::getMotion9(int16_t* ax, int16_t* ay, int16_t* az, int16_t* gx, int16_t* gy, int16_t* gz, int16_t* mx, int16_t* my, int16_t* mz) {
+ getMotion6(ax, ay, az, gx, gy, gz);
+ // TODO: magnetometer integration
+}
+/** Get raw 6-axis motion sensor readings (accel/gyro).
+ * Retrieves all currently available motion sensor values.
+ * @param ax 16-bit signed integer container for accelerometer X-axis value
+ * @param ay 16-bit signed integer container for accelerometer Y-axis value
+ * @param az 16-bit signed integer container for accelerometer Z-axis value
+ * @param gx 16-bit signed integer container for gyroscope X-axis value
+ * @param gy 16-bit signed integer container for gyroscope Y-axis value
+ * @param gz 16-bit signed integer container for gyroscope Z-axis value
+ * @see getAcceleration()
+ * @see getRotation()
+ * @see MPU6050_RA_ACCEL_XOUT_H
+ */
+void MPU6050::getMotion6(int16_t* ax, int16_t* ay, int16_t* az, int16_t* gx, int16_t* gy, int16_t* gz) {
+ I2Cdev::readBytes(devAddr, MPU6050_RA_ACCEL_XOUT_H, 14, buffer);
+ *ax = (((int16_t)buffer[0]) << 8) | buffer[1];
+ *ay = (((int16_t)buffer[2]) << 8) | buffer[3];
+ *az = (((int16_t)buffer[4]) << 8) | buffer[5];
+ *gx = (((int16_t)buffer[8]) << 8) | buffer[9];
+ *gy = (((int16_t)buffer[10]) << 8) | buffer[11];
+ *gz = (((int16_t)buffer[12]) << 8) | buffer[13];
+}
+/** Get 3-axis accelerometer readings.
+ * These registers store the most recent accelerometer measurements.
+ * Accelerometer measurements are written to these registers at the Sample Rate
+ * as defined in Register 25.
+ *
+ * The accelerometer measurement registers, along with the temperature
+ * measurement registers, gyroscope measurement registers, and external sensor
+ * data registers, are composed of two sets of registers: an internal register
+ * set and a user-facing read register set.
+ *
+ * The data within the accelerometer sensors' internal register set is always
+ * updated at the Sample Rate. Meanwhile, the user-facing read register set
+ * duplicates the internal register set's data values whenever the serial
+ * interface is idle. This guarantees that a burst read of sensor registers will
+ * read measurements from the same sampling instant. Note that if burst reads
+ * are not used, the user is responsible for ensuring a set of single byte reads
+ * correspond to a single sampling instant by checking the Data Ready interrupt.
+ *
+ * Each 16-bit accelerometer measurement has a full scale defined in ACCEL_FS
+ * (Register 28). For each full scale setting, the accelerometers' sensitivity
+ * per LSB in ACCEL_xOUT is shown in the table below:
+ *
+ *
+ * AFS_SEL | Full Scale Range | LSB Sensitivity
+ * --------+------------------+----------------
+ * 0 | +/- 2g | 8192 LSB/mg
+ * 1 | +/- 4g | 4096 LSB/mg
+ * 2 | +/- 8g | 2048 LSB/mg
+ * 3 | +/- 16g | 1024 LSB/mg
+ *
+ *
+ * @param x 16-bit signed integer container for X-axis acceleration
+ * @param y 16-bit signed integer container for Y-axis acceleration
+ * @param z 16-bit signed integer container for Z-axis acceleration
+ * @see MPU6050_RA_GYRO_XOUT_H
+ */
+void MPU6050::getAcceleration(int16_t* x, int16_t* y, int16_t* z) {
+ I2Cdev::readBytes(devAddr, MPU6050_RA_ACCEL_XOUT_H, 6, buffer);
+ *x = (((int16_t)buffer[0]) << 8) | buffer[1];
+ *y = (((int16_t)buffer[2]) << 8) | buffer[3];
+ *z = (((int16_t)buffer[4]) << 8) | buffer[5];
+}
+/** Get X-axis accelerometer reading.
+ * @return X-axis acceleration measurement in 16-bit 2's complement format
+ * @see getMotion6()
+ * @see MPU6050_RA_ACCEL_XOUT_H
+ */
+int16_t MPU6050::getAccelerationX() {
+ I2Cdev::readBytes(devAddr, MPU6050_RA_ACCEL_XOUT_H, 2, buffer);
+ return (((int16_t)buffer[0]) << 8) | buffer[1];
+}
+/** Get Y-axis accelerometer reading.
+ * @return Y-axis acceleration measurement in 16-bit 2's complement format
+ * @see getMotion6()
+ * @see MPU6050_RA_ACCEL_YOUT_H
+ */
+int16_t MPU6050::getAccelerationY() {
+ I2Cdev::readBytes(devAddr, MPU6050_RA_ACCEL_YOUT_H, 2, buffer);
+ return (((int16_t)buffer[0]) << 8) | buffer[1];
+}
+/** Get Z-axis accelerometer reading.
+ * @return Z-axis acceleration measurement in 16-bit 2's complement format
+ * @see getMotion6()
+ * @see MPU6050_RA_ACCEL_ZOUT_H
+ */
+int16_t MPU6050::getAccelerationZ() {
+ I2Cdev::readBytes(devAddr, MPU6050_RA_ACCEL_ZOUT_H, 2, buffer);
+ return (((int16_t)buffer[0]) << 8) | buffer[1];
+}
+
+// TEMP_OUT_* registers
+
+/** Get current internal temperature.
+ * @return Temperature reading in 16-bit 2's complement format
+ * @see MPU6050_RA_TEMP_OUT_H
+ */
+int16_t MPU6050::getTemperature() {
+ I2Cdev::readBytes(devAddr, MPU6050_RA_TEMP_OUT_H, 2, buffer);
+ return (((int16_t)buffer[0]) << 8) | buffer[1];
+}
+
+// GYRO_*OUT_* registers
+
+/** Get 3-axis gyroscope readings.
+ * These gyroscope measurement registers, along with the accelerometer
+ * measurement registers, temperature measurement registers, and external sensor
+ * data registers, are composed of two sets of registers: an internal register
+ * set and a user-facing read register set.
+ * The data within the gyroscope sensors' internal register set is always
+ * updated at the Sample Rate. Meanwhile, the user-facing read register set
+ * duplicates the internal register set's data values whenever the serial
+ * interface is idle. This guarantees that a burst read of sensor registers will
+ * read measurements from the same sampling instant. Note that if burst reads
+ * are not used, the user is responsible for ensuring a set of single byte reads
+ * correspond to a single sampling instant by checking the Data Ready interrupt.
+ *
+ * Each 16-bit gyroscope measurement has a full scale defined in FS_SEL
+ * (Register 27). For each full scale setting, the gyroscopes' sensitivity per
+ * LSB in GYRO_xOUT is shown in the table below:
+ *
+ *
+ * FS_SEL | Full Scale Range | LSB Sensitivity
+ * -------+--------------------+----------------
+ * 0 | +/- 250 degrees/s | 131 LSB/deg/s
+ * 1 | +/- 500 degrees/s | 65.5 LSB/deg/s
+ * 2 | +/- 1000 degrees/s | 32.8 LSB/deg/s
+ * 3 | +/- 2000 degrees/s | 16.4 LSB/deg/s
+ *
+ *
+ * @param x 16-bit signed integer container for X-axis rotation
+ * @param y 16-bit signed integer container for Y-axis rotation
+ * @param z 16-bit signed integer container for Z-axis rotation
+ * @see getMotion6()
+ * @see MPU6050_RA_GYRO_XOUT_H
+ */
+void MPU6050::getRotation(int16_t* x, int16_t* y, int16_t* z) {
+ I2Cdev::readBytes(devAddr, MPU6050_RA_GYRO_XOUT_H, 6, buffer);
+ *x = (((int16_t)buffer[0]) << 8) | buffer[1];
+ *y = (((int16_t)buffer[2]) << 8) | buffer[3];
+ *z = (((int16_t)buffer[4]) << 8) | buffer[5];
+}
+/** Get X-axis gyroscope reading.
+ * @return X-axis rotation measurement in 16-bit 2's complement format
+ * @see getMotion6()
+ * @see MPU6050_RA_GYRO_XOUT_H
+ */
+int16_t MPU6050::getRotationX() {
+ I2Cdev::readBytes(devAddr, MPU6050_RA_GYRO_XOUT_H, 2, buffer);
+ return (((int16_t)buffer[0]) << 8) | buffer[1];
+}
+/** Get Y-axis gyroscope reading.
+ * @return Y-axis rotation measurement in 16-bit 2's complement format
+ * @see getMotion6()
+ * @see MPU6050_RA_GYRO_YOUT_H
+ */
+int16_t MPU6050::getRotationY() {
+ I2Cdev::readBytes(devAddr, MPU6050_RA_GYRO_YOUT_H, 2, buffer);
+ return (((int16_t)buffer[0]) << 8) | buffer[1];
+}
+/** Get Z-axis gyroscope reading.
+ * @return Z-axis rotation measurement in 16-bit 2's complement format
+ * @see getMotion6()
+ * @see MPU6050_RA_GYRO_ZOUT_H
+ */
+int16_t MPU6050::getRotationZ() {
+ I2Cdev::readBytes(devAddr, MPU6050_RA_GYRO_ZOUT_H, 2, buffer);
+ return (((int16_t)buffer[0]) << 8) | buffer[1];
+}
+
+// EXT_SENS_DATA_* registers
+
+/** Read single byte from external sensor data register.
+ * These registers store data read from external sensors by the Slave 0, 1, 2,
+ * and 3 on the auxiliary I2C interface. Data read by Slave 4 is stored in
+ * I2C_SLV4_DI (Register 53).
+ *
+ * External sensor data is written to these registers at the Sample Rate as
+ * defined in Register 25. This access rate can be reduced by using the Slave
+ * Delay Enable registers (Register 103).
+ *
+ * External sensor data registers, along with the gyroscope measurement
+ * registers, accelerometer measurement registers, and temperature measurement
+ * registers, are composed of two sets of registers: an internal register set
+ * and a user-facing read register set.
+ *
+ * The data within the external sensors' internal register set is always updated
+ * at the Sample Rate (or the reduced access rate) whenever the serial interface
+ * is idle. This guarantees that a burst read of sensor registers will read
+ * measurements from the same sampling instant. Note that if burst reads are not
+ * used, the user is responsible for ensuring a set of single byte reads
+ * correspond to a single sampling instant by checking the Data Ready interrupt.
+ *
+ * Data is placed in these external sensor data registers according to
+ * I2C_SLV0_CTRL, I2C_SLV1_CTRL, I2C_SLV2_CTRL, and I2C_SLV3_CTRL (Registers 39,
+ * 42, 45, and 48). When more than zero bytes are read (I2C_SLVx_LEN > 0) from
+ * an enabled slave (I2C_SLVx_EN = 1), the slave is read at the Sample Rate (as
+ * defined in Register 25) or delayed rate (if specified in Register 52 and
+ * 103). During each Sample cycle, slave reads are performed in order of Slave
+ * number. If all slaves are enabled with more than zero bytes to be read, the
+ * order will be Slave 0, followed by Slave 1, Slave 2, and Slave 3.
+ *
+ * Each enabled slave will have EXT_SENS_DATA registers associated with it by
+ * number of bytes read (I2C_SLVx_LEN) in order of slave number, starting from
+ * EXT_SENS_DATA_00. Note that this means enabling or disabling a slave may
+ * change the higher numbered slaves' associated registers. Furthermore, if
+ * fewer total bytes are being read from the external sensors as a result of
+ * such a change, then the data remaining in the registers which no longer have
+ * an associated slave device (i.e. high numbered registers) will remain in
+ * these previously allocated registers unless reset.
+ *
+ * If the sum of the read lengths of all SLVx transactions exceed the number of
+ * available EXT_SENS_DATA registers, the excess bytes will be dropped. There
+ * are 24 EXT_SENS_DATA registers and hence the total read lengths between all
+ * the slaves cannot be greater than 24 or some bytes will be lost.
+ *
+ * Note: Slave 4's behavior is distinct from that of Slaves 0-3. For further
+ * information regarding the characteristics of Slave 4, please refer to
+ * Registers 49 to 53.
+ *
+ * EXAMPLE:
+ * Suppose that Slave 0 is enabled with 4 bytes to be read (I2C_SLV0_EN = 1 and
+ * I2C_SLV0_LEN = 4) while Slave 1 is enabled with 2 bytes to be read so that
+ * I2C_SLV1_EN = 1 and I2C_SLV1_LEN = 2. In such a situation, EXT_SENS_DATA _00
+ * through _03 will be associated with Slave 0, while EXT_SENS_DATA _04 and 05
+ * will be associated with Slave 1. If Slave 2 is enabled as well, registers
+ * starting from EXT_SENS_DATA_06 will be allocated to Slave 2.
+ *
+ * If Slave 2 is disabled while Slave 3 is enabled in this same situation, then
+ * registers starting from EXT_SENS_DATA_06 will be allocated to Slave 3
+ * instead.
+ *
+ * REGISTER ALLOCATION FOR DYNAMIC DISABLE VS. NORMAL DISABLE:
+ * If a slave is disabled at any time, the space initially allocated to the
+ * slave in the EXT_SENS_DATA register, will remain associated with that slave.
+ * This is to avoid dynamic adjustment of the register allocation.
+ *
+ * The allocation of the EXT_SENS_DATA registers is recomputed only when (1) all
+ * slaves are disabled, or (2) the I2C_MST_RST bit is set (Register 106).
+ *
+ * This above is also true if one of the slaves gets NACKed and stops
+ * functioning.
+ *
+ * @param position Starting position (0-23)
+ * @return Byte read from register
+ */
+uint8_t MPU6050::getExternalSensorByte(int position) {
+ I2Cdev::readByte(devAddr, MPU6050_RA_EXT_SENS_DATA_00 + position, buffer);
+ return buffer[0];
+}
+/** Read word (2 bytes) from external sensor data registers.
+ * @param position Starting position (0-21)
+ * @return Word read from register
+ * @see getExternalSensorByte()
+ */
+uint16_t MPU6050::getExternalSensorWord(int position) {
+ I2Cdev::readBytes(devAddr, MPU6050_RA_EXT_SENS_DATA_00 + position, 2, buffer);
+ return (((uint16_t)buffer[0]) << 8) | buffer[1];
+}
+/** Read double word (4 bytes) from external sensor data registers.
+ * @param position Starting position (0-20)
+ * @return Double word read from registers
+ * @see getExternalSensorByte()
+ */
+uint32_t MPU6050::getExternalSensorDWord(int position) {
+ I2Cdev::readBytes(devAddr, MPU6050_RA_EXT_SENS_DATA_00 + position, 4, buffer);
+ return (((uint32_t)buffer[0]) << 24) | (((uint32_t)buffer[1]) << 16) | (((uint16_t)buffer[2]) << 8) | buffer[3];
+}
+
+// MOT_DETECT_STATUS register
+
+/** Get full motion detection status register content (all bits).
+ * @return Motion detection status byte
+ * @see MPU6050_RA_MOT_DETECT_STATUS
+ */
+uint8_t MPU6050::getMotionStatus() {
+ I2Cdev::readByte(devAddr, MPU6050_RA_MOT_DETECT_STATUS, buffer);
+ return buffer[0];
+}
+/** Get X-axis negative motion detection interrupt status.
+ * @return Motion detection status
+ * @see MPU6050_RA_MOT_DETECT_STATUS
+ * @see MPU6050_MOTION_MOT_XNEG_BIT
+ */
+bool MPU6050::getXNegMotionDetected() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_MOT_DETECT_STATUS, MPU6050_MOTION_MOT_XNEG_BIT, buffer);
+ return buffer[0];
+}
+/** Get X-axis positive motion detection interrupt status.
+ * @return Motion detection status
+ * @see MPU6050_RA_MOT_DETECT_STATUS
+ * @see MPU6050_MOTION_MOT_XPOS_BIT
+ */
+bool MPU6050::getXPosMotionDetected() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_MOT_DETECT_STATUS, MPU6050_MOTION_MOT_XPOS_BIT, buffer);
+ return buffer[0];
+}
+/** Get Y-axis negative motion detection interrupt status.
+ * @return Motion detection status
+ * @see MPU6050_RA_MOT_DETECT_STATUS
+ * @see MPU6050_MOTION_MOT_YNEG_BIT
+ */
+bool MPU6050::getYNegMotionDetected() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_MOT_DETECT_STATUS, MPU6050_MOTION_MOT_YNEG_BIT, buffer);
+ return buffer[0];
+}
+/** Get Y-axis positive motion detection interrupt status.
+ * @return Motion detection status
+ * @see MPU6050_RA_MOT_DETECT_STATUS
+ * @see MPU6050_MOTION_MOT_YPOS_BIT
+ */
+bool MPU6050::getYPosMotionDetected() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_MOT_DETECT_STATUS, MPU6050_MOTION_MOT_YPOS_BIT, buffer);
+ return buffer[0];
+}
+/** Get Z-axis negative motion detection interrupt status.
+ * @return Motion detection status
+ * @see MPU6050_RA_MOT_DETECT_STATUS
+ * @see MPU6050_MOTION_MOT_ZNEG_BIT
+ */
+bool MPU6050::getZNegMotionDetected() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_MOT_DETECT_STATUS, MPU6050_MOTION_MOT_ZNEG_BIT, buffer);
+ return buffer[0];
+}
+/** Get Z-axis positive motion detection interrupt status.
+ * @return Motion detection status
+ * @see MPU6050_RA_MOT_DETECT_STATUS
+ * @see MPU6050_MOTION_MOT_ZPOS_BIT
+ */
+bool MPU6050::getZPosMotionDetected() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_MOT_DETECT_STATUS, MPU6050_MOTION_MOT_ZPOS_BIT, buffer);
+ return buffer[0];
+}
+/** Get zero motion detection interrupt status.
+ * @return Motion detection status
+ * @see MPU6050_RA_MOT_DETECT_STATUS
+ * @see MPU6050_MOTION_MOT_ZRMOT_BIT
+ */
+bool MPU6050::getZeroMotionDetected() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_MOT_DETECT_STATUS, MPU6050_MOTION_MOT_ZRMOT_BIT, buffer);
+ return buffer[0];
+}
+
+// I2C_SLV*_DO register
+
+/** Write byte to Data Output container for specified slave.
+ * This register holds the output data written into Slave when Slave is set to
+ * write mode. For further information regarding Slave control, please
+ * refer to Registers 37 to 39 and immediately following.
+ * @param num Slave number (0-3)
+ * @param data Byte to write
+ * @see MPU6050_RA_I2C_SLV0_DO
+ */
+void MPU6050::setSlaveOutputByte(uint8_t num, uint8_t data) {
+ if (num > 3) return;
+ I2Cdev::writeByte(devAddr, MPU6050_RA_I2C_SLV0_DO + num, data);
+}
+
+// I2C_MST_DELAY_CTRL register
+
+/** Get external data shadow delay enabled status.
+ * This register is used to specify the timing of external sensor data
+ * shadowing. When DELAY_ES_SHADOW is set to 1, shadowing of external
+ * sensor data is delayed until all data has been received.
+ * @return Current external data shadow delay enabled status.
+ * @see MPU6050_RA_I2C_MST_DELAY_CTRL
+ * @see MPU6050_DELAYCTRL_DELAY_ES_SHADOW_BIT
+ */
+bool MPU6050::getExternalShadowDelayEnabled() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_I2C_MST_DELAY_CTRL, MPU6050_DELAYCTRL_DELAY_ES_SHADOW_BIT, buffer);
+ return buffer[0];
+}
+/** Set external data shadow delay enabled status.
+ * @param enabled New external data shadow delay enabled status.
+ * @see getExternalShadowDelayEnabled()
+ * @see MPU6050_RA_I2C_MST_DELAY_CTRL
+ * @see MPU6050_DELAYCTRL_DELAY_ES_SHADOW_BIT
+ */
+void MPU6050::setExternalShadowDelayEnabled(bool enabled) {
+ I2Cdev::writeBit(devAddr, MPU6050_RA_I2C_MST_DELAY_CTRL, MPU6050_DELAYCTRL_DELAY_ES_SHADOW_BIT, enabled);
+}
+/** Get slave delay enabled status.
+ * When a particular slave delay is enabled, the rate of access for the that
+ * slave device is reduced. When a slave's access rate is decreased relative to
+ * the Sample Rate, the slave is accessed every:
+ *
+ * 1 / (1 + I2C_MST_DLY) Samples
+ *
+ * This base Sample Rate in turn is determined by SMPLRT_DIV (register * 25)
+ * and DLPF_CFG (register 26).
+ *
+ * For further information regarding I2C_MST_DLY, please refer to register 52.
+ * For further information regarding the Sample Rate, please refer to register 25.
+ *
+ * @param num Slave number (0-4)
+ * @return Current slave delay enabled status.
+ * @see MPU6050_RA_I2C_MST_DELAY_CTRL
+ * @see MPU6050_DELAYCTRL_I2C_SLV0_DLY_EN_BIT
+ */
+bool MPU6050::getSlaveDelayEnabled(uint8_t num) {
+ // MPU6050_DELAYCTRL_I2C_SLV4_DLY_EN_BIT is 4, SLV3 is 3, etc.
+ if (num > 4) return 0;
+ I2Cdev::readBit(devAddr, MPU6050_RA_I2C_MST_DELAY_CTRL, num, buffer);
+ return buffer[0];
+}
+/** Set slave delay enabled status.
+ * @param num Slave number (0-4)
+ * @param enabled New slave delay enabled status.
+ * @see MPU6050_RA_I2C_MST_DELAY_CTRL
+ * @see MPU6050_DELAYCTRL_I2C_SLV0_DLY_EN_BIT
+ */
+void MPU6050::setSlaveDelayEnabled(uint8_t num, bool enabled) {
+ I2Cdev::writeBit(devAddr, MPU6050_RA_I2C_MST_DELAY_CTRL, num, enabled);
+}
+
+// SIGNAL_PATH_RESET register
+
+/** Reset gyroscope signal path.
+ * The reset will revert the signal path analog to digital converters and
+ * filters to their power up configurations.
+ * @see MPU6050_RA_SIGNAL_PATH_RESET
+ * @see MPU6050_PATHRESET_GYRO_RESET_BIT
+ */
+void MPU6050::resetGyroscopePath() {
+ I2Cdev::writeBit(devAddr, MPU6050_RA_SIGNAL_PATH_RESET, MPU6050_PATHRESET_GYRO_RESET_BIT, true);
+}
+/** Reset accelerometer signal path.
+ * The reset will revert the signal path analog to digital converters and
+ * filters to their power up configurations.
+ * @see MPU6050_RA_SIGNAL_PATH_RESET
+ * @see MPU6050_PATHRESET_ACCEL_RESET_BIT
+ */
+void MPU6050::resetAccelerometerPath() {
+ I2Cdev::writeBit(devAddr, MPU6050_RA_SIGNAL_PATH_RESET, MPU6050_PATHRESET_ACCEL_RESET_BIT, true);
+}
+/** Reset temperature sensor signal path.
+ * The reset will revert the signal path analog to digital converters and
+ * filters to their power up configurations.
+ * @see MPU6050_RA_SIGNAL_PATH_RESET
+ * @see MPU6050_PATHRESET_TEMP_RESET_BIT
+ */
+void MPU6050::resetTemperaturePath() {
+ I2Cdev::writeBit(devAddr, MPU6050_RA_SIGNAL_PATH_RESET, MPU6050_PATHRESET_TEMP_RESET_BIT, true);
+}
+
+// MOT_DETECT_CTRL register
+
+/** Get accelerometer power-on delay.
+ * The accelerometer data path provides samples to the sensor registers, Motion
+ * detection, Zero Motion detection, and Free Fall detection modules. The
+ * signal path contains filters which must be flushed on wake-up with new
+ * samples before the detection modules begin operations. The default wake-up
+ * delay, of 4ms can be lengthened by up to 3ms. This additional delay is
+ * specified in ACCEL_ON_DELAY in units of 1 LSB = 1 ms. The user may select
+ * any value above zero unless instructed otherwise by InvenSense. Please refer
+ * to Section 8 of the MPU-6000/MPU-6050 Product Specification document for
+ * further information regarding the detection modules.
+ * @return Current accelerometer power-on delay
+ * @see MPU6050_RA_MOT_DETECT_CTRL
+ * @see MPU6050_DETECT_ACCEL_ON_DELAY_BIT
+ */
+uint8_t MPU6050::getAccelerometerPowerOnDelay() {
+ I2Cdev::readBits(devAddr, MPU6050_RA_MOT_DETECT_CTRL, MPU6050_DETECT_ACCEL_ON_DELAY_BIT, MPU6050_DETECT_ACCEL_ON_DELAY_LENGTH, buffer);
+ return buffer[0];
+}
+/** Set accelerometer power-on delay.
+ * @param delay New accelerometer power-on delay (0-3)
+ * @see getAccelerometerPowerOnDelay()
+ * @see MPU6050_RA_MOT_DETECT_CTRL
+ * @see MPU6050_DETECT_ACCEL_ON_DELAY_BIT
+ */
+void MPU6050::setAccelerometerPowerOnDelay(uint8_t delay) {
+ I2Cdev::writeBits(devAddr, MPU6050_RA_MOT_DETECT_CTRL, MPU6050_DETECT_ACCEL_ON_DELAY_BIT, MPU6050_DETECT_ACCEL_ON_DELAY_LENGTH, delay);
+}
+/** Get Free Fall detection counter decrement configuration.
+ * Detection is registered by the Free Fall detection module after accelerometer
+ * measurements meet their respective threshold conditions over a specified
+ * number of samples. When the threshold conditions are met, the corresponding
+ * detection counter increments by 1. The user may control the rate at which the
+ * detection counter decrements when the threshold condition is not met by
+ * configuring FF_COUNT. The decrement rate can be set according to the
+ * following table:
+ *
+ *
+ * FF_COUNT | Counter Decrement
+ * ---------+------------------
+ * 0 | Reset
+ * 1 | 1
+ * 2 | 2
+ * 3 | 4
+ *
+ *
+ * When FF_COUNT is configured to 0 (reset), any non-qualifying sample will
+ * reset the counter to 0. For further information on Free Fall detection,
+ * please refer to Registers 29 to 32.
+ *
+ * @return Current decrement configuration
+ * @see MPU6050_RA_MOT_DETECT_CTRL
+ * @see MPU6050_DETECT_FF_COUNT_BIT
+ */
+uint8_t MPU6050::getFreefallDetectionCounterDecrement() {
+ I2Cdev::readBits(devAddr, MPU6050_RA_MOT_DETECT_CTRL, MPU6050_DETECT_FF_COUNT_BIT, MPU6050_DETECT_FF_COUNT_LENGTH, buffer);
+ return buffer[0];
+}
+/** Set Free Fall detection counter decrement configuration.
+ * @param decrement New decrement configuration value
+ * @see getFreefallDetectionCounterDecrement()
+ * @see MPU6050_RA_MOT_DETECT_CTRL
+ * @see MPU6050_DETECT_FF_COUNT_BIT
+ */
+void MPU6050::setFreefallDetectionCounterDecrement(uint8_t decrement) {
+ I2Cdev::writeBits(devAddr, MPU6050_RA_MOT_DETECT_CTRL, MPU6050_DETECT_FF_COUNT_BIT, MPU6050_DETECT_FF_COUNT_LENGTH, decrement);
+}
+/** Get Motion detection counter decrement configuration.
+ * Detection is registered by the Motion detection module after accelerometer
+ * measurements meet their respective threshold conditions over a specified
+ * number of samples. When the threshold conditions are met, the corresponding
+ * detection counter increments by 1. The user may control the rate at which the
+ * detection counter decrements when the threshold condition is not met by
+ * configuring MOT_COUNT. The decrement rate can be set according to the
+ * following table:
+ *
+ *
+ * MOT_COUNT | Counter Decrement
+ * ----------+------------------
+ * 0 | Reset
+ * 1 | 1
+ * 2 | 2
+ * 3 | 4
+ *
+ *
+ * When MOT_COUNT is configured to 0 (reset), any non-qualifying sample will
+ * reset the counter to 0. For further information on Motion detection,
+ * please refer to Registers 29 to 32.
+ *
+ */
+uint8_t MPU6050::getMotionDetectionCounterDecrement() {
+ I2Cdev::readBits(devAddr, MPU6050_RA_MOT_DETECT_CTRL, MPU6050_DETECT_MOT_COUNT_BIT, MPU6050_DETECT_MOT_COUNT_LENGTH, buffer);
+ return buffer[0];
+}
+/** Set Motion detection counter decrement configuration.
+ * @param decrement New decrement configuration value
+ * @see getMotionDetectionCounterDecrement()
+ * @see MPU6050_RA_MOT_DETECT_CTRL
+ * @see MPU6050_DETECT_MOT_COUNT_BIT
+ */
+void MPU6050::setMotionDetectionCounterDecrement(uint8_t decrement) {
+ I2Cdev::writeBits(devAddr, MPU6050_RA_MOT_DETECT_CTRL, MPU6050_DETECT_MOT_COUNT_BIT, MPU6050_DETECT_MOT_COUNT_LENGTH, decrement);
+}
+
+// USER_CTRL register
+
+/** Get FIFO enabled status.
+ * When this bit is set to 0, the FIFO buffer is disabled. The FIFO buffer
+ * cannot be written to or read from while disabled. The FIFO buffer's state
+ * does not change unless the MPU-60X0 is power cycled.
+ * @return Current FIFO enabled status
+ * @see MPU6050_RA_USER_CTRL
+ * @see MPU6050_USERCTRL_FIFO_EN_BIT
+ */
+bool MPU6050::getFIFOEnabled() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_USER_CTRL, MPU6050_USERCTRL_FIFO_EN_BIT, buffer);
+ return buffer[0];
+}
+/** Set FIFO enabled status.
+ * @param enabled New FIFO enabled status
+ * @see getFIFOEnabled()
+ * @see MPU6050_RA_USER_CTRL
+ * @see MPU6050_USERCTRL_FIFO_EN_BIT
+ */
+void MPU6050::setFIFOEnabled(bool enabled) {
+ I2Cdev::writeBit(devAddr, MPU6050_RA_USER_CTRL, MPU6050_USERCTRL_FIFO_EN_BIT, enabled);
+}
+/** Get I2C Master Mode enabled status.
+ * When this mode is enabled, the MPU-60X0 acts as the I2C Master to the
+ * external sensor slave devices on the auxiliary I2C bus. When this bit is
+ * cleared to 0, the auxiliary I2C bus lines (AUX_DA and AUX_CL) are logically
+ * driven by the primary I2C bus (SDA and SCL). This is a precondition to
+ * enabling Bypass Mode. For further information regarding Bypass Mode, please
+ * refer to Register 55.
+ * @return Current I2C Master Mode enabled status
+ * @see MPU6050_RA_USER_CTRL
+ * @see MPU6050_USERCTRL_I2C_MST_EN_BIT
+ */
+bool MPU6050::getI2CMasterModeEnabled() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_USER_CTRL, MPU6050_USERCTRL_I2C_MST_EN_BIT, buffer);
+ return buffer[0];
+}
+/** Set I2C Master Mode enabled status.
+ * @param enabled New I2C Master Mode enabled status
+ * @see getI2CMasterModeEnabled()
+ * @see MPU6050_RA_USER_CTRL
+ * @see MPU6050_USERCTRL_I2C_MST_EN_BIT
+ */
+void MPU6050::setI2CMasterModeEnabled(bool enabled) {
+ I2Cdev::writeBit(devAddr, MPU6050_RA_USER_CTRL, MPU6050_USERCTRL_I2C_MST_EN_BIT, enabled);
+}
+/** Switch from I2C to SPI mode (MPU-6000 only)
+ * If this is set, the primary SPI interface will be enabled in place of the
+ * disabled primary I2C interface.
+ */
+void MPU6050::switchSPIEnabled(bool enabled) {
+ I2Cdev::writeBit(devAddr, MPU6050_RA_USER_CTRL, MPU6050_USERCTRL_I2C_IF_DIS_BIT, enabled);
+}
+/** Reset the FIFO.
+ * This bit resets the FIFO buffer when set to 1 while FIFO_EN equals 0. This
+ * bit automatically clears to 0 after the reset has been triggered.
+ * @see MPU6050_RA_USER_CTRL
+ * @see MPU6050_USERCTRL_FIFO_RESET_BIT
+ */
+void MPU6050::resetFIFO() {
+ I2Cdev::writeBit(devAddr, MPU6050_RA_USER_CTRL, MPU6050_USERCTRL_FIFO_RESET_BIT, true);
+}
+/** Reset the I2C Master.
+ * This bit resets the I2C Master when set to 1 while I2C_MST_EN equals 0.
+ * This bit automatically clears to 0 after the reset has been triggered.
+ * @see MPU6050_RA_USER_CTRL
+ * @see MPU6050_USERCTRL_I2C_MST_RESET_BIT
+ */
+void MPU6050::resetI2CMaster() {
+ I2Cdev::writeBit(devAddr, MPU6050_RA_USER_CTRL, MPU6050_USERCTRL_I2C_MST_RESET_BIT, true);
+}
+/** Reset all sensor registers and signal paths.
+ * When set to 1, this bit resets the signal paths for all sensors (gyroscopes,
+ * accelerometers, and temperature sensor). This operation will also clear the
+ * sensor registers. This bit automatically clears to 0 after the reset has been
+ * triggered.
+ *
+ * When resetting only the signal path (and not the sensor registers), please
+ * use Register 104, SIGNAL_PATH_RESET.
+ *
+ * @see MPU6050_RA_USER_CTRL
+ * @see MPU6050_USERCTRL_SIG_COND_RESET_BIT
+ */
+void MPU6050::resetSensors() {
+ I2Cdev::writeBit(devAddr, MPU6050_RA_USER_CTRL, MPU6050_USERCTRL_SIG_COND_RESET_BIT, true);
+}
+
+// PWR_MGMT_1 register
+
+/** Trigger a full device reset.
+ * A small delay of ~50ms may be desirable after triggering a reset.
+ * @see MPU6050_RA_PWR_MGMT_1
+ * @see MPU6050_PWR1_DEVICE_RESET_BIT
+ */
+void MPU6050::reset() {
+ I2Cdev::writeBit(devAddr, MPU6050_RA_PWR_MGMT_1, MPU6050_PWR1_DEVICE_RESET_BIT, true);
+}
+/** Get sleep mode status.
+ * Setting the SLEEP bit in the register puts the device into very low power
+ * sleep mode. In this mode, only the serial interface and internal registers
+ * remain active, allowing for a very low standby current. Clearing this bit
+ * puts the device back into normal mode. To save power, the individual standby
+ * selections for each of the gyros should be used if any gyro axis is not used
+ * by the application.
+ * @return Current sleep mode enabled status
+ * @see MPU6050_RA_PWR_MGMT_1
+ * @see MPU6050_PWR1_SLEEP_BIT
+ */
+bool MPU6050::getSleepEnabled() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_PWR_MGMT_1, MPU6050_PWR1_SLEEP_BIT, buffer);
+ return buffer[0];
+}
+/** Set sleep mode status.
+ * @param enabled New sleep mode enabled status
+ * @see getSleepEnabled()
+ * @see MPU6050_RA_PWR_MGMT_1
+ * @see MPU6050_PWR1_SLEEP_BIT
+ */
+void MPU6050::setSleepEnabled(bool enabled) {
+ I2Cdev::writeBit(devAddr, MPU6050_RA_PWR_MGMT_1, MPU6050_PWR1_SLEEP_BIT, enabled);
+}
+/** Get wake cycle enabled status.
+ * When this bit is set to 1 and SLEEP is disabled, the MPU-60X0 will cycle
+ * between sleep mode and waking up to take a single sample of data from active
+ * sensors at a rate determined by LP_WAKE_CTRL (register 108).
+ * @return Current sleep mode enabled status
+ * @see MPU6050_RA_PWR_MGMT_1
+ * @see MPU6050_PWR1_CYCLE_BIT
+ */
+bool MPU6050::getWakeCycleEnabled() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_PWR_MGMT_1, MPU6050_PWR1_CYCLE_BIT, buffer);
+ return buffer[0];
+}
+/** Set wake cycle enabled status.
+ * @param enabled New sleep mode enabled status
+ * @see getWakeCycleEnabled()
+ * @see MPU6050_RA_PWR_MGMT_1
+ * @see MPU6050_PWR1_CYCLE_BIT
+ */
+void MPU6050::setWakeCycleEnabled(bool enabled) {
+ I2Cdev::writeBit(devAddr, MPU6050_RA_PWR_MGMT_1, MPU6050_PWR1_CYCLE_BIT, enabled);
+}
+/** Get temperature sensor enabled status.
+ * Control the usage of the internal temperature sensor.
+ *
+ * Note: this register stores the *disabled* value, but for consistency with the
+ * rest of the code, the function is named and used with standard true/false
+ * values to indicate whether the sensor is enabled or disabled, respectively.
+ *
+ * @return Current temperature sensor enabled status
+ * @see MPU6050_RA_PWR_MGMT_1
+ * @see MPU6050_PWR1_TEMP_DIS_BIT
+ */
+bool MPU6050::getTempSensorEnabled() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_PWR_MGMT_1, MPU6050_PWR1_TEMP_DIS_BIT, buffer);
+ return buffer[0] == 0; // 1 is actually disabled here
+}
+/** Set temperature sensor enabled status.
+ * Note: this register stores the *disabled* value, but for consistency with the
+ * rest of the code, the function is named and used with standard true/false
+ * values to indicate whether the sensor is enabled or disabled, respectively.
+ *
+ * @param enabled New temperature sensor enabled status
+ * @see getTempSensorEnabled()
+ * @see MPU6050_RA_PWR_MGMT_1
+ * @see MPU6050_PWR1_TEMP_DIS_BIT
+ */
+void MPU6050::setTempSensorEnabled(bool enabled) {
+ // 1 is actually disabled here
+ I2Cdev::writeBit(devAddr, MPU6050_RA_PWR_MGMT_1, MPU6050_PWR1_TEMP_DIS_BIT, !enabled);
+}
+/** Get clock source setting.
+ * @return Current clock source setting
+ * @see MPU6050_RA_PWR_MGMT_1
+ * @see MPU6050_PWR1_CLKSEL_BIT
+ * @see MPU6050_PWR1_CLKSEL_LENGTH
+ */
+uint8_t MPU6050::getClockSource() {
+ I2Cdev::readBits(devAddr, MPU6050_RA_PWR_MGMT_1, MPU6050_PWR1_CLKSEL_BIT, MPU6050_PWR1_CLKSEL_LENGTH, buffer);
+ return buffer[0];
+}
+/** Set clock source setting.
+ * An internal 8MHz oscillator, gyroscope based clock, or external sources can
+ * be selected as the MPU-60X0 clock source. When the internal 8 MHz oscillator
+ * or an external source is chosen as the clock source, the MPU-60X0 can operate
+ * in low power modes with the gyroscopes disabled.
+ *
+ * Upon power up, the MPU-60X0 clock source defaults to the internal oscillator.
+ * However, it is highly recommended that the device be configured to use one of
+ * the gyroscopes (or an external clock source) as the clock reference for
+ * improved stability. The clock source can be selected according to the following table:
+ *
+ *
+ * CLK_SEL | Clock Source
+ * --------+--------------------------------------
+ * 0 | Internal oscillator
+ * 1 | PLL with X Gyro reference
+ * 2 | PLL with Y Gyro reference
+ * 3 | PLL with Z Gyro reference
+ * 4 | PLL with external 32.768kHz reference
+ * 5 | PLL with external 19.2MHz reference
+ * 6 | Reserved
+ * 7 | Stops the clock and keeps the timing generator in reset
+ *
+ *
+ * @param source New clock source setting
+ * @see getClockSource()
+ * @see MPU6050_RA_PWR_MGMT_1
+ * @see MPU6050_PWR1_CLKSEL_BIT
+ * @see MPU6050_PWR1_CLKSEL_LENGTH
+ */
+void MPU6050::setClockSource(uint8_t source) {
+ I2Cdev::writeBits(devAddr, MPU6050_RA_PWR_MGMT_1, MPU6050_PWR1_CLKSEL_BIT, MPU6050_PWR1_CLKSEL_LENGTH, source);
+}
+
+// PWR_MGMT_2 register
+
+/** Get wake frequency in Accel-Only Low Power Mode.
+ * The MPU-60X0 can be put into Accerlerometer Only Low Power Mode by setting
+ * PWRSEL to 1 in the Power Management 1 register (Register 107). In this mode,
+ * the device will power off all devices except for the primary I2C interface,
+ * waking only the accelerometer at fixed intervals to take a single
+ * measurement. The frequency of wake-ups can be configured with LP_WAKE_CTRL
+ * as shown below:
+ *
+ *
+ * LP_WAKE_CTRL | Wake-up Frequency
+ * -------------+------------------
+ * 0 | 1.25 Hz
+ * 1 | 2.5 Hz
+ * 2 | 5 Hz
+ * 3 | 10 Hz
+ *
+ *
+ * For further information regarding the MPU-60X0's power modes, please refer to
+ * Register 107.
+ *
+ * @return Current wake frequency
+ * @see MPU6050_RA_PWR_MGMT_2
+ */
+uint8_t MPU6050::getWakeFrequency() {
+ I2Cdev::readBits(devAddr, MPU6050_RA_PWR_MGMT_2, MPU6050_PWR2_LP_WAKE_CTRL_BIT, MPU6050_PWR2_LP_WAKE_CTRL_LENGTH, buffer);
+ return buffer[0];
+}
+/** Set wake frequency in Accel-Only Low Power Mode.
+ * @param frequency New wake frequency
+ * @see MPU6050_RA_PWR_MGMT_2
+ */
+void MPU6050::setWakeFrequency(uint8_t frequency) {
+ I2Cdev::writeBits(devAddr, MPU6050_RA_PWR_MGMT_2, MPU6050_PWR2_LP_WAKE_CTRL_BIT, MPU6050_PWR2_LP_WAKE_CTRL_LENGTH, frequency);
+}
+
+/** Get X-axis accelerometer standby enabled status.
+ * If enabled, the X-axis will not gather or report data (or use power).
+ * @return Current X-axis standby enabled status
+ * @see MPU6050_RA_PWR_MGMT_2
+ * @see MPU6050_PWR2_STBY_XA_BIT
+ */
+bool MPU6050::getStandbyXAccelEnabled() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_PWR_MGMT_2, MPU6050_PWR2_STBY_XA_BIT, buffer);
+ return buffer[0];
+}
+/** Set X-axis accelerometer standby enabled status.
+ * @param New X-axis standby enabled status
+ * @see getStandbyXAccelEnabled()
+ * @see MPU6050_RA_PWR_MGMT_2
+ * @see MPU6050_PWR2_STBY_XA_BIT
+ */
+void MPU6050::setStandbyXAccelEnabled(bool enabled) {
+ I2Cdev::writeBit(devAddr, MPU6050_RA_PWR_MGMT_2, MPU6050_PWR2_STBY_XA_BIT, enabled);
+}
+/** Get Y-axis accelerometer standby enabled status.
+ * If enabled, the Y-axis will not gather or report data (or use power).
+ * @return Current Y-axis standby enabled status
+ * @see MPU6050_RA_PWR_MGMT_2
+ * @see MPU6050_PWR2_STBY_YA_BIT
+ */
+bool MPU6050::getStandbyYAccelEnabled() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_PWR_MGMT_2, MPU6050_PWR2_STBY_YA_BIT, buffer);
+ return buffer[0];
+}
+/** Set Y-axis accelerometer standby enabled status.
+ * @param New Y-axis standby enabled status
+ * @see getStandbyYAccelEnabled()
+ * @see MPU6050_RA_PWR_MGMT_2
+ * @see MPU6050_PWR2_STBY_YA_BIT
+ */
+void MPU6050::setStandbyYAccelEnabled(bool enabled) {
+ I2Cdev::writeBit(devAddr, MPU6050_RA_PWR_MGMT_2, MPU6050_PWR2_STBY_YA_BIT, enabled);
+}
+/** Get Z-axis accelerometer standby enabled status.
+ * If enabled, the Z-axis will not gather or report data (or use power).
+ * @return Current Z-axis standby enabled status
+ * @see MPU6050_RA_PWR_MGMT_2
+ * @see MPU6050_PWR2_STBY_ZA_BIT
+ */
+bool MPU6050::getStandbyZAccelEnabled() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_PWR_MGMT_2, MPU6050_PWR2_STBY_ZA_BIT, buffer);
+ return buffer[0];
+}
+/** Set Z-axis accelerometer standby enabled status.
+ * @param New Z-axis standby enabled status
+ * @see getStandbyZAccelEnabled()
+ * @see MPU6050_RA_PWR_MGMT_2
+ * @see MPU6050_PWR2_STBY_ZA_BIT
+ */
+void MPU6050::setStandbyZAccelEnabled(bool enabled) {
+ I2Cdev::writeBit(devAddr, MPU6050_RA_PWR_MGMT_2, MPU6050_PWR2_STBY_ZA_BIT, enabled);
+}
+/** Get X-axis gyroscope standby enabled status.
+ * If enabled, the X-axis will not gather or report data (or use power).
+ * @return Current X-axis standby enabled status
+ * @see MPU6050_RA_PWR_MGMT_2
+ * @see MPU6050_PWR2_STBY_XG_BIT
+ */
+bool MPU6050::getStandbyXGyroEnabled() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_PWR_MGMT_2, MPU6050_PWR2_STBY_XG_BIT, buffer);
+ return buffer[0];
+}
+/** Set X-axis gyroscope standby enabled status.
+ * @param New X-axis standby enabled status
+ * @see getStandbyXGyroEnabled()
+ * @see MPU6050_RA_PWR_MGMT_2
+ * @see MPU6050_PWR2_STBY_XG_BIT
+ */
+void MPU6050::setStandbyXGyroEnabled(bool enabled) {
+ I2Cdev::writeBit(devAddr, MPU6050_RA_PWR_MGMT_2, MPU6050_PWR2_STBY_XG_BIT, enabled);
+}
+/** Get Y-axis gyroscope standby enabled status.
+ * If enabled, the Y-axis will not gather or report data (or use power).
+ * @return Current Y-axis standby enabled status
+ * @see MPU6050_RA_PWR_MGMT_2
+ * @see MPU6050_PWR2_STBY_YG_BIT
+ */
+bool MPU6050::getStandbyYGyroEnabled() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_PWR_MGMT_2, MPU6050_PWR2_STBY_YG_BIT, buffer);
+ return buffer[0];
+}
+/** Set Y-axis gyroscope standby enabled status.
+ * @param New Y-axis standby enabled status
+ * @see getStandbyYGyroEnabled()
+ * @see MPU6050_RA_PWR_MGMT_2
+ * @see MPU6050_PWR2_STBY_YG_BIT
+ */
+void MPU6050::setStandbyYGyroEnabled(bool enabled) {
+ I2Cdev::writeBit(devAddr, MPU6050_RA_PWR_MGMT_2, MPU6050_PWR2_STBY_YG_BIT, enabled);
+}
+/** Get Z-axis gyroscope standby enabled status.
+ * If enabled, the Z-axis will not gather or report data (or use power).
+ * @return Current Z-axis standby enabled status
+ * @see MPU6050_RA_PWR_MGMT_2
+ * @see MPU6050_PWR2_STBY_ZG_BIT
+ */
+bool MPU6050::getStandbyZGyroEnabled() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_PWR_MGMT_2, MPU6050_PWR2_STBY_ZG_BIT, buffer);
+ return buffer[0];
+}
+/** Set Z-axis gyroscope standby enabled status.
+ * @param New Z-axis standby enabled status
+ * @see getStandbyZGyroEnabled()
+ * @see MPU6050_RA_PWR_MGMT_2
+ * @see MPU6050_PWR2_STBY_ZG_BIT
+ */
+void MPU6050::setStandbyZGyroEnabled(bool enabled) {
+ I2Cdev::writeBit(devAddr, MPU6050_RA_PWR_MGMT_2, MPU6050_PWR2_STBY_ZG_BIT, enabled);
+}
+
+// FIFO_COUNT* registers
+
+/** Get current FIFO buffer size.
+ * This value indicates the number of bytes stored in the FIFO buffer. This
+ * number is in turn the number of bytes that can be read from the FIFO buffer
+ * and it is directly proportional to the number of samples available given the
+ * set of sensor data bound to be stored in the FIFO (register 35 and 36).
+ * @return Current FIFO buffer size
+ */
+uint16_t MPU6050::getFIFOCount() {
+ I2Cdev::readBytes(devAddr, MPU6050_RA_FIFO_COUNTH, 2, buffer);
+ return (((uint16_t)buffer[0]) << 8) | buffer[1];
+}
+
+// FIFO_R_W register
+
+/** Get byte from FIFO buffer.
+ * This register is used to read and write data from the FIFO buffer. Data is
+ * written to the FIFO in order of register number (from lowest to highest). If
+ * all the FIFO enable flags (see below) are enabled and all External Sensor
+ * Data registers (Registers 73 to 96) are associated with a Slave device, the
+ * contents of registers 59 through 96 will be written in order at the Sample
+ * Rate.
+ *
+ * The contents of the sensor data registers (Registers 59 to 96) are written
+ * into the FIFO buffer when their corresponding FIFO enable flags are set to 1
+ * in FIFO_EN (Register 35). An additional flag for the sensor data registers
+ * associated with I2C Slave 3 can be found in I2C_MST_CTRL (Register 36).
+ *
+ * If the FIFO buffer has overflowed, the status bit FIFO_OFLOW_INT is
+ * automatically set to 1. This bit is located in INT_STATUS (Register 58).
+ * When the FIFO buffer has overflowed, the oldest data will be lost and new
+ * data will be written to the FIFO.
+ *
+ * If the FIFO buffer is empty, reading this register will return the last byte
+ * that was previously read from the FIFO until new data is available. The user
+ * should check FIFO_COUNT to ensure that the FIFO buffer is not read when
+ * empty.
+ *
+ * @return Byte from FIFO buffer
+ */
+uint8_t MPU6050::getFIFOByte() {
+ I2Cdev::readByte(devAddr, MPU6050_RA_FIFO_R_W, buffer);
+ return buffer[0];
+}
+void MPU6050::getFIFOBytes(uint8_t *data, uint8_t length) {
+ if(length > 0){
+ I2Cdev::readBytes(devAddr, MPU6050_RA_FIFO_R_W, length, data);
+ } else {
+ *data = 0;
+ }
+}
+/** Write byte to FIFO buffer.
+ * @see getFIFOByte()
+ * @see MPU6050_RA_FIFO_R_W
+ */
+void MPU6050::setFIFOByte(uint8_t data) {
+ I2Cdev::writeByte(devAddr, MPU6050_RA_FIFO_R_W, data);
+}
+
+// WHO_AM_I register
+
+/** Get Device ID.
+ * This register is used to verify the identity of the device (0b110100, 0x34).
+ * @return Device ID (6 bits only! should be 0x34)
+ * @see MPU6050_RA_WHO_AM_I
+ * @see MPU6050_WHO_AM_I_BIT
+ * @see MPU6050_WHO_AM_I_LENGTH
+ */
+uint8_t MPU6050::getDeviceID() {
+ I2Cdev::readBits(devAddr, MPU6050_RA_WHO_AM_I, MPU6050_WHO_AM_I_BIT, MPU6050_WHO_AM_I_LENGTH, buffer);
+ return buffer[0];
+}
+/** Set Device ID.
+ * Write a new ID into the WHO_AM_I register (no idea why this should ever be
+ * necessary though).
+ * @param id New device ID to set.
+ * @see getDeviceID()
+ * @see MPU6050_RA_WHO_AM_I
+ * @see MPU6050_WHO_AM_I_BIT
+ * @see MPU6050_WHO_AM_I_LENGTH
+ */
+void MPU6050::setDeviceID(uint8_t id) {
+ I2Cdev::writeBits(devAddr, MPU6050_RA_WHO_AM_I, MPU6050_WHO_AM_I_BIT, MPU6050_WHO_AM_I_LENGTH, id);
+}
+
+// ======== UNDOCUMENTED/DMP REGISTERS/METHODS ========
+
+// XG_OFFS_TC register
+
+uint8_t MPU6050::getOTPBankValid() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_XG_OFFS_TC, MPU6050_TC_OTP_BNK_VLD_BIT, buffer);
+ return buffer[0];
+}
+void MPU6050::setOTPBankValid(bool enabled) {
+ I2Cdev::writeBit(devAddr, MPU6050_RA_XG_OFFS_TC, MPU6050_TC_OTP_BNK_VLD_BIT, enabled);
+}
+int8_t MPU6050::getXGyroOffsetTC() {
+ I2Cdev::readBits(devAddr, MPU6050_RA_XG_OFFS_TC, MPU6050_TC_OFFSET_BIT, MPU6050_TC_OFFSET_LENGTH, buffer);
+ return buffer[0];
+}
+void MPU6050::setXGyroOffsetTC(int8_t offset) {
+ I2Cdev::writeBits(devAddr, MPU6050_RA_XG_OFFS_TC, MPU6050_TC_OFFSET_BIT, MPU6050_TC_OFFSET_LENGTH, offset);
+}
+
+// YG_OFFS_TC register
+
+int8_t MPU6050::getYGyroOffsetTC() {
+ I2Cdev::readBits(devAddr, MPU6050_RA_YG_OFFS_TC, MPU6050_TC_OFFSET_BIT, MPU6050_TC_OFFSET_LENGTH, buffer);
+ return buffer[0];
+}
+void MPU6050::setYGyroOffsetTC(int8_t offset) {
+ I2Cdev::writeBits(devAddr, MPU6050_RA_YG_OFFS_TC, MPU6050_TC_OFFSET_BIT, MPU6050_TC_OFFSET_LENGTH, offset);
+}
+
+// ZG_OFFS_TC register
+
+int8_t MPU6050::getZGyroOffsetTC() {
+ I2Cdev::readBits(devAddr, MPU6050_RA_ZG_OFFS_TC, MPU6050_TC_OFFSET_BIT, MPU6050_TC_OFFSET_LENGTH, buffer);
+ return buffer[0];
+}
+void MPU6050::setZGyroOffsetTC(int8_t offset) {
+ I2Cdev::writeBits(devAddr, MPU6050_RA_ZG_OFFS_TC, MPU6050_TC_OFFSET_BIT, MPU6050_TC_OFFSET_LENGTH, offset);
+}
+
+// X_FINE_GAIN register
+
+int8_t MPU6050::getXFineGain() {
+ I2Cdev::readByte(devAddr, MPU6050_RA_X_FINE_GAIN, buffer);
+ return buffer[0];
+}
+void MPU6050::setXFineGain(int8_t gain) {
+ I2Cdev::writeByte(devAddr, MPU6050_RA_X_FINE_GAIN, gain);
+}
+
+// Y_FINE_GAIN register
+
+int8_t MPU6050::getYFineGain() {
+ I2Cdev::readByte(devAddr, MPU6050_RA_Y_FINE_GAIN, buffer);
+ return buffer[0];
+}
+void MPU6050::setYFineGain(int8_t gain) {
+ I2Cdev::writeByte(devAddr, MPU6050_RA_Y_FINE_GAIN, gain);
+}
+
+// Z_FINE_GAIN register
+
+int8_t MPU6050::getZFineGain() {
+ I2Cdev::readByte(devAddr, MPU6050_RA_Z_FINE_GAIN, buffer);
+ return buffer[0];
+}
+void MPU6050::setZFineGain(int8_t gain) {
+ I2Cdev::writeByte(devAddr, MPU6050_RA_Z_FINE_GAIN, gain);
+}
+
+// XA_OFFS_* registers
+
+int16_t MPU6050::getXAccelOffset() {
+ uint8_t SaveAddress = ((getDeviceID() < 0x38 )? MPU6050_RA_XA_OFFS_H:0x77); // MPU6050,MPU9150 Vs MPU6500,MPU9250
+ I2Cdev::readBytes(devAddr, SaveAddress, 2, buffer);
+ return (((int16_t)buffer[0]) << 8) | buffer[1];
+}
+void MPU6050::setXAccelOffset(int16_t offset) {
+ uint8_t SaveAddress = ((getDeviceID() < 0x38 )? MPU6050_RA_XA_OFFS_H:0x77); // MPU6050,MPU9150 Vs MPU6500,MPU9250
+ I2Cdev::writeWord(devAddr, SaveAddress, offset);
+}
+
+// YA_OFFS_* register
+
+int16_t MPU6050::getYAccelOffset() {
+ uint8_t SaveAddress = ((getDeviceID() < 0x38 )? MPU6050_RA_YA_OFFS_H:0x7A); // MPU6050,MPU9150 Vs MPU6500,MPU9250
+ I2Cdev::readBytes(devAddr, SaveAddress, 2, buffer);
+ return (((int16_t)buffer[0]) << 8) | buffer[1];
+}
+void MPU6050::setYAccelOffset(int16_t offset) {
+ uint8_t SaveAddress = ((getDeviceID() < 0x38 )? MPU6050_RA_YA_OFFS_H:0x7A); // MPU6050,MPU9150 Vs MPU6500,MPU9250
+ I2Cdev::writeWord(devAddr, SaveAddress, offset);
+}
+
+// ZA_OFFS_* register
+
+int16_t MPU6050::getZAccelOffset() {
+ uint8_t SaveAddress = ((getDeviceID() < 0x38 )? MPU6050_RA_ZA_OFFS_H:0x7D); // MPU6050,MPU9150 Vs MPU6500,MPU9250
+ I2Cdev::readBytes(devAddr, SaveAddress, 2, buffer);
+ return (((int16_t)buffer[0]) << 8) | buffer[1];
+}
+void MPU6050::setZAccelOffset(int16_t offset) {
+ uint8_t SaveAddress = ((getDeviceID() < 0x38 )? MPU6050_RA_ZA_OFFS_H:0x7D); // MPU6050,MPU9150 Vs MPU6500,MPU9250
+ I2Cdev::writeWord(devAddr, SaveAddress, offset);
+}
+
+// XG_OFFS_USR* registers
+
+int16_t MPU6050::getXGyroOffset() {
+ I2Cdev::readBytes(devAddr, MPU6050_RA_XG_OFFS_USRH, 2, buffer);
+ return (((int16_t)buffer[0]) << 8) | buffer[1];
+}
+void MPU6050::setXGyroOffset(int16_t offset) {
+ I2Cdev::writeWord(devAddr, MPU6050_RA_XG_OFFS_USRH, offset);
+}
+
+// YG_OFFS_USR* register
+
+int16_t MPU6050::getYGyroOffset() {
+ I2Cdev::readBytes(devAddr, MPU6050_RA_YG_OFFS_USRH, 2, buffer);
+ return (((int16_t)buffer[0]) << 8) | buffer[1];
+}
+void MPU6050::setYGyroOffset(int16_t offset) {
+ I2Cdev::writeWord(devAddr, MPU6050_RA_YG_OFFS_USRH, offset);
+}
+
+// ZG_OFFS_USR* register
+
+int16_t MPU6050::getZGyroOffset() {
+ I2Cdev::readBytes(devAddr, MPU6050_RA_ZG_OFFS_USRH, 2, buffer);
+ return (((int16_t)buffer[0]) << 8) | buffer[1];
+}
+void MPU6050::setZGyroOffset(int16_t offset) {
+ I2Cdev::writeWord(devAddr, MPU6050_RA_ZG_OFFS_USRH, offset);
+}
+
+// INT_ENABLE register (DMP functions)
+
+bool MPU6050::getIntPLLReadyEnabled() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_INT_ENABLE, MPU6050_INTERRUPT_PLL_RDY_INT_BIT, buffer);
+ return buffer[0];
+}
+void MPU6050::setIntPLLReadyEnabled(bool enabled) {
+ I2Cdev::writeBit(devAddr, MPU6050_RA_INT_ENABLE, MPU6050_INTERRUPT_PLL_RDY_INT_BIT, enabled);
+}
+bool MPU6050::getIntDMPEnabled() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_INT_ENABLE, MPU6050_INTERRUPT_DMP_INT_BIT, buffer);
+ return buffer[0];
+}
+void MPU6050::setIntDMPEnabled(bool enabled) {
+ I2Cdev::writeBit(devAddr, MPU6050_RA_INT_ENABLE, MPU6050_INTERRUPT_DMP_INT_BIT, enabled);
+}
+
+// DMP_INT_STATUS
+
+bool MPU6050::getDMPInt5Status() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_DMP_INT_STATUS, MPU6050_DMPINT_5_BIT, buffer);
+ return buffer[0];
+}
+bool MPU6050::getDMPInt4Status() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_DMP_INT_STATUS, MPU6050_DMPINT_4_BIT, buffer);
+ return buffer[0];
+}
+bool MPU6050::getDMPInt3Status() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_DMP_INT_STATUS, MPU6050_DMPINT_3_BIT, buffer);
+ return buffer[0];
+}
+bool MPU6050::getDMPInt2Status() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_DMP_INT_STATUS, MPU6050_DMPINT_2_BIT, buffer);
+ return buffer[0];
+}
+bool MPU6050::getDMPInt1Status() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_DMP_INT_STATUS, MPU6050_DMPINT_1_BIT, buffer);
+ return buffer[0];
+}
+bool MPU6050::getDMPInt0Status() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_DMP_INT_STATUS, MPU6050_DMPINT_0_BIT, buffer);
+ return buffer[0];
+}
+
+// INT_STATUS register (DMP functions)
+
+bool MPU6050::getIntPLLReadyStatus() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_INT_STATUS, MPU6050_INTERRUPT_PLL_RDY_INT_BIT, buffer);
+ return buffer[0];
+}
+bool MPU6050::getIntDMPStatus() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_INT_STATUS, MPU6050_INTERRUPT_DMP_INT_BIT, buffer);
+ return buffer[0];
+}
+
+// USER_CTRL register (DMP functions)
+
+bool MPU6050::getDMPEnabled() {
+ I2Cdev::readBit(devAddr, MPU6050_RA_USER_CTRL, MPU6050_USERCTRL_DMP_EN_BIT, buffer);
+ return buffer[0];
+}
+void MPU6050::setDMPEnabled(bool enabled) {
+ I2Cdev::writeBit(devAddr, MPU6050_RA_USER_CTRL, MPU6050_USERCTRL_DMP_EN_BIT, enabled);
+}
+void MPU6050::resetDMP() {
+ I2Cdev::writeBit(devAddr, MPU6050_RA_USER_CTRL, MPU6050_USERCTRL_DMP_RESET_BIT, true);
+}
+
+// BANK_SEL register
+
+void MPU6050::setMemoryBank(uint8_t bank, bool prefetchEnabled, bool userBank) {
+ bank &= 0x1F;
+ if (userBank) bank |= 0x20;
+ if (prefetchEnabled) bank |= 0x40;
+ I2Cdev::writeByte(devAddr, MPU6050_RA_BANK_SEL, bank);
+}
+
+// MEM_START_ADDR register
+
+void MPU6050::setMemoryStartAddress(uint8_t address) {
+ I2Cdev::writeByte(devAddr, MPU6050_RA_MEM_START_ADDR, address);
+}
+
+// MEM_R_W register
+
+uint8_t MPU6050::readMemoryByte() {
+ I2Cdev::readByte(devAddr, MPU6050_RA_MEM_R_W, buffer);
+ return buffer[0];
+}
+void MPU6050::writeMemoryByte(uint8_t data) {
+ I2Cdev::writeByte(devAddr, MPU6050_RA_MEM_R_W, data);
+}
+void MPU6050::readMemoryBlock(uint8_t *data, uint16_t dataSize, uint8_t bank, uint8_t address) {
+ setMemoryBank(bank);
+ setMemoryStartAddress(address);
+ uint8_t chunkSize;
+ for (uint16_t i = 0; i < dataSize;) {
+ // determine correct chunk size according to bank position and data size
+ chunkSize = MPU6050_DMP_MEMORY_CHUNK_SIZE;
+
+ // make sure we don't go past the data size
+ if (i + chunkSize > dataSize) chunkSize = dataSize - i;
+
+ // make sure this chunk doesn't go past the bank boundary (256 bytes)
+ if (chunkSize > 256 - address) chunkSize = 256 - address;
+
+ // read the chunk of data as specified
+ I2Cdev::readBytes(devAddr, MPU6050_RA_MEM_R_W, chunkSize, data + i);
+
+ // increase byte index by [chunkSize]
+ i += chunkSize;
+
+ // uint8_t automatically wraps to 0 at 256
+ address += chunkSize;
+
+ // if we aren't done, update bank (if necessary) and address
+ if (i < dataSize) {
+ if (address == 0) bank++;
+ setMemoryBank(bank);
+ setMemoryStartAddress(address);
+ }
+ }
+}
+bool MPU6050::writeMemoryBlock(const uint8_t *data, uint16_t dataSize, uint8_t bank, uint8_t address, bool verify, bool useProgMem) {
+ setMemoryBank(bank);
+ setMemoryStartAddress(address);
+ uint8_t chunkSize;
+ uint8_t *verifyBuffer=0;
+ uint8_t *progBuffer=0;
+ uint16_t i;
+ uint8_t j;
+ if (verify) verifyBuffer = (uint8_t *)malloc(MPU6050_DMP_MEMORY_CHUNK_SIZE);
+ if (useProgMem) progBuffer = (uint8_t *)malloc(MPU6050_DMP_MEMORY_CHUNK_SIZE);
+ for (i = 0; i < dataSize;) {
+ // determine correct chunk size according to bank position and data size
+ chunkSize = MPU6050_DMP_MEMORY_CHUNK_SIZE;
+
+ // make sure we don't go past the data size
+ if (i + chunkSize > dataSize) chunkSize = dataSize - i;
+
+ // make sure this chunk doesn't go past the bank boundary (256 bytes)
+ if (chunkSize > 256 - address) chunkSize = 256 - address;
+
+ if (useProgMem) {
+ // write the chunk of data as specified
+ for (j = 0; j < chunkSize; j++) progBuffer[j] = pgm_read_byte(data + i + j);
+ } else {
+ // write the chunk of data as specified
+ progBuffer = (uint8_t *)data + i;
+ }
+
+ I2Cdev::writeBytes(devAddr, MPU6050_RA_MEM_R_W, chunkSize, progBuffer);
+
+ // verify data if needed
+ if (verify && verifyBuffer) {
+ setMemoryBank(bank);
+ setMemoryStartAddress(address);
+ I2Cdev::readBytes(devAddr, MPU6050_RA_MEM_R_W, chunkSize, verifyBuffer);
+ if (memcmp(progBuffer, verifyBuffer, chunkSize) != 0) {
+ /*Serial.print("Block write verification error, bank ");
+ Serial.print(bank, DEC);
+ Serial.print(", address ");
+ Serial.print(address, DEC);
+ Serial.print("!\nExpected:");
+ for (j = 0; j < chunkSize; j++) {
+ Serial.print(" 0x");
+ if (progBuffer[j] < 16) Serial.print("0");
+ Serial.print(progBuffer[j], HEX);
+ }
+ Serial.print("\nReceived:");
+ for (uint8_t j = 0; j < chunkSize; j++) {
+ Serial.print(" 0x");
+ if (verifyBuffer[i + j] < 16) Serial.print("0");
+ Serial.print(verifyBuffer[i + j], HEX);
+ }
+ Serial.print("\n");*/
+ free(verifyBuffer);
+ if (useProgMem) free(progBuffer);
+ return false; // uh oh.
+ }
+ }
+
+ // increase byte index by [chunkSize]
+ i += chunkSize;
+
+ // uint8_t automatically wraps to 0 at 256
+ address += chunkSize;
+
+ // if we aren't done, update bank (if necessary) and address
+ if (i < dataSize) {
+ if (address == 0) bank++;
+ setMemoryBank(bank);
+ setMemoryStartAddress(address);
+ }
+ }
+ if (verify) free(verifyBuffer);
+ if (useProgMem) free(progBuffer);
+ return true;
+}
+bool MPU6050::writeProgMemoryBlock(const uint8_t *data, uint16_t dataSize, uint8_t bank, uint8_t address, bool verify) {
+ return writeMemoryBlock(data, dataSize, bank, address, verify, true);
+}
+bool MPU6050::writeDMPConfigurationSet(const uint8_t *data, uint16_t dataSize, bool useProgMem) {
+ uint8_t *progBuffer = 0;
+ uint8_t success, special;
+ uint16_t i, j;
+ if (useProgMem) {
+ progBuffer = (uint8_t *)malloc(8); // assume 8-byte blocks, realloc later if necessary
+ }
+
+ // config set data is a long string of blocks with the following structure:
+ // [bank] [offset] [length] [byte[0], byte[1], ..., byte[length]]
+ uint8_t bank, offset, length;
+ for (i = 0; i < dataSize;) {
+ if (useProgMem) {
+ bank = pgm_read_byte(data + i++);
+ offset = pgm_read_byte(data + i++);
+ length = pgm_read_byte(data + i++);
+ } else {
+ bank = data[i++];
+ offset = data[i++];
+ length = data[i++];
+ }
+
+ // write data or perform special action
+ if (length > 0) {
+ // regular block of data to write
+ /*Serial.print("Writing config block to bank ");
+ Serial.print(bank);
+ Serial.print(", offset ");
+ Serial.print(offset);
+ Serial.print(", length=");
+ Serial.println(length);*/
+ if (useProgMem) {
+ if (sizeof(progBuffer) < length) progBuffer = (uint8_t *)realloc(progBuffer, length);
+ for (j = 0; j < length; j++) progBuffer[j] = pgm_read_byte(data + i + j);
+ } else {
+ progBuffer = (uint8_t *)data + i;
+ }
+ success = writeMemoryBlock(progBuffer, length, bank, offset, true);
+ i += length;
+ } else {
+ // special instruction
+ // NOTE: this kind of behavior (what and when to do certain things)
+ // is totally undocumented. This code is in here based on observed
+ // behavior only, and exactly why (or even whether) it has to be here
+ // is anybody's guess for now.
+ if (useProgMem) {
+ special = pgm_read_byte(data + i++);
+ } else {
+ special = data[i++];
+ }
+ /*Serial.print("Special command code ");
+ Serial.print(special, HEX);
+ Serial.println(" found...");*/
+ if (special == 0x01) {
+ // enable DMP-related interrupts
+
+ //setIntZeroMotionEnabled(true);
+ //setIntFIFOBufferOverflowEnabled(true);
+ //setIntDMPEnabled(true);
+ I2Cdev::writeByte(devAddr, MPU6050_RA_INT_ENABLE, 0x32); // single operation
+
+ success = true;
+ } else {
+ // unknown special command
+ success = false;
+ }
+ }
+
+ if (!success) {
+ if (useProgMem) free(progBuffer);
+ return false; // uh oh
+ }
+ }
+ if (useProgMem) free(progBuffer);
+ return true;
+}
+bool MPU6050::writeProgDMPConfigurationSet(const uint8_t *data, uint16_t dataSize) {
+ return writeDMPConfigurationSet(data, dataSize, true);
+}
+
+// DMP_CFG_1 register
+
+uint8_t MPU6050::getDMPConfig1() {
+ I2Cdev::readByte(devAddr, MPU6050_RA_DMP_CFG_1, buffer);
+ return buffer[0];
+}
+void MPU6050::setDMPConfig1(uint8_t config) {
+ I2Cdev::writeByte(devAddr, MPU6050_RA_DMP_CFG_1, config);
+}
+
+// DMP_CFG_2 register
+
+uint8_t MPU6050::getDMPConfig2() {
+ I2Cdev::readByte(devAddr, MPU6050_RA_DMP_CFG_2, buffer);
+ return buffer[0];
+}
+void MPU6050::setDMPConfig2(uint8_t config) {
+ I2Cdev::writeByte(devAddr, MPU6050_RA_DMP_CFG_2, config);
+}
+
+
+//***************************************************************************************
+//********************** Calibration Routines **********************
+//***************************************************************************************
+/**
+ @brief Fully calibrate Gyro from ZERO in about 6-7 Loops 600-700 readings
+*/
+void MPU6050::CalibrateGyro(uint8_t Loops ) {
+ double kP = 0.3;
+ double kI = 90;
+ float x;
+ x = (100 - map(Loops, 1, 5, 20, 0)) * .01;
+ kP *= x;
+ kI *= x;
+
+ PID( 0x43, kP, kI, Loops);
+}
+
+/**
+ @brief Fully calibrate Accel from ZERO in about 6-7 Loops 600-700 readings
+*/
+void MPU6050::CalibrateAccel(uint8_t Loops ) {
+
+ float kP = 0.3;
+ float kI = 20;
+ float x;
+ x = (100 - map(Loops, 1, 5, 20, 0)) * .01;
+ kP *= x;
+ kI *= x;
+ PID( 0x3B, kP, kI, Loops);
+}
+
+void MPU6050::PID(uint8_t ReadAddress, float kP,float kI, uint8_t Loops){
+ uint8_t SaveAddress = (ReadAddress == 0x3B)?((getDeviceID() < 0x38 )? 0x06:0x77):0x13;
+
+ int16_t Data;
+ float Reading;
+ int16_t BitZero[3];
+ uint8_t shift =(SaveAddress == 0x77)?3:2;
+ float Error, PTerm, ITerm[3];
+ int16_t eSample;
+ uint32_t eSum ;
+ Serial.write('>');
+ for (int i = 0; i < 3; i++) {
+ I2Cdev::readWords(devAddr, SaveAddress + (i * shift), 1, (uint16_t *)&Data); // reads 1 or more 16 bit integers (Word)
+ Reading = Data;
+ if(SaveAddress != 0x13){
+ BitZero[i] = Data & 1; // Capture Bit Zero to properly handle Accelerometer calibration
+ ITerm[i] = ((float)Reading) * 8;
+ } else {
+ ITerm[i] = Reading * 4;
+ }
+ }
+ for (int L = 0; L < Loops; L++) {
+ eSample = 0;
+ for (int c = 0; c < 100; c++) {// 100 PI Calculations
+ eSum = 0;
+ for (int i = 0; i < 3; i++) {
+ I2Cdev::readWords(devAddr, ReadAddress + (i * 2), 1, (uint16_t *)&Data); // reads 1 or more 16 bit integers (Word)
+ Reading = Data;
+ if ((ReadAddress == 0x3B)&&(i == 2)) Reading -= 16384; //remove Gravity
+ Error = -Reading;
+ eSum += abs(Reading);
+ PTerm = kP * Error;
+ ITerm[i] += (Error * 0.001) * kI; // Integral term 1000 Calculations a second = 0.001
+ if(SaveAddress != 0x13){
+ Data = round((PTerm + ITerm[i] ) / 8); //Compute PID Output
+ Data = ((Data)&0xFFFE) |BitZero[i]; // Insert Bit0 Saved at beginning
+ } else Data = round((PTerm + ITerm[i] ) / 4); //Compute PID Output
+ I2Cdev::writeWords(devAddr, SaveAddress + (i * shift), 1, (uint16_t *)&Data);
+ }
+ if((c == 99) && eSum > 1000){ // Error is still to great to continue
+ c = 0;
+ Serial.write('*');
+ }
+ if((eSum * ((ReadAddress == 0x3B)?.05: 1)) < 5) eSample++; // Successfully found offsets prepare to advance
+ if((eSum < 100) && (c > 10) && (eSample >= 10)) break; // Advance to next Loop
+ delay(1);
+ }
+ Serial.write('.');
+ kP *= .75;
+ kI *= .75;
+ for (int i = 0; i < 3; i++){
+ if(SaveAddress != 0x13) {
+ Data = round((ITerm[i] ) / 8); //Compute PID Output
+ Data = ((Data)&0xFFFE) |BitZero[i]; // Insert Bit0 Saved at beginning
+ } else Data = round((ITerm[i]) / 4);
+ I2Cdev::writeWords(devAddr, SaveAddress + (i * shift), 1, (uint16_t *)&Data);
+ }
+ }
+ resetFIFO();
+ resetDMP();
+}
+
+#define printfloatx(Name,Variable,Spaces,Precision,EndTxt) { Serial.print(F(Name)); {char S[(Spaces + Precision + 3)];Serial.print(F(" ")); Serial.print(dtostrf((float)Variable,Spaces,Precision ,S));}Serial.print(F(EndTxt)); }//Name,Variable,Spaces,Precision,EndTxt
+void MPU6050::PrintActiveOffsets() {
+ uint8_t AOffsetRegister = (getDeviceID() < 0x38 )? MPU6050_RA_XA_OFFS_H:0x77;
+ int16_t Data[3];
+ //Serial.print(F("Offset Register 0x"));
+ //Serial.print(AOffsetRegister>>4,HEX);Serial.print(AOffsetRegister&0x0F,HEX);
+ Serial.print(F("\n// X Accel Y Accel Z Accel X Gyro Y Gyro Z Gyro\n//OFFSETS "));
+ if(AOffsetRegister == 0x06) I2Cdev::readWords(devAddr, AOffsetRegister, 3, (uint16_t *)Data);
+ else {
+ I2Cdev::readWords(devAddr, AOffsetRegister, 1, (uint16_t *)Data);
+ I2Cdev::readWords(devAddr, AOffsetRegister+3, 1, (uint16_t *)Data+1);
+ I2Cdev::readWords(devAddr, AOffsetRegister+6, 1, (uint16_t *)Data+2);
+ }
+ // A_OFFSET_H_READ_A_OFFS(Data);
+ printfloatx("", Data[0], 5, 0, ", ");
+ printfloatx("", Data[1], 5, 0, ", ");
+ printfloatx("", Data[2], 5, 0, ", ");
+ I2Cdev::readWords(devAddr, 0x13, 3, (uint16_t *)Data);
+ // XG_OFFSET_H_READ_OFFS_USR(Data);
+ printfloatx("", Data[0], 5, 0, ", ");
+ printfloatx("", Data[1], 5, 0, ", ");
+ printfloatx("", Data[2], 5, 0, "\n");
+}
diff --git a/Versions/dRehmFlight_ESP32_BETA_1.3/src/MPU6050/MPU6050.h b/Versions/dRehmFlight_ESP32_BETA_1.3/src/MPU6050/MPU6050.h
new file mode 100644
index 00000000..871f423a
--- /dev/null
+++ b/Versions/dRehmFlight_ESP32_BETA_1.3/src/MPU6050/MPU6050.h
@@ -0,0 +1,1041 @@
+// I2Cdev library collection - MPU6050 I2C device class
+// Based on InvenSense MPU-6050 register map document rev. 2.0, 5/19/2011 (RM-MPU-6000A-00)
+// 10/3/2011 by Jeff Rowberg
+// Updates should (hopefully) always be available at https://github.com/jrowberg/i2cdevlib
+//
+// Changelog:
+// ... - ongoing debug release
+
+// NOTE: THIS IS ONLY A PARIAL RELEASE. THIS DEVICE CLASS IS CURRENTLY UNDERGOING ACTIVE
+// DEVELOPMENT AND IS STILL MISSING SOME IMPORTANT FEATURES. PLEASE KEEP THIS IN MIND IF
+// YOU DECIDE TO USE THIS PARTICULAR CODE FOR ANYTHING.
+
+/* ============================================
+I2Cdev device library code is placed under the MIT license
+Copyright (c) 2012 Jeff Rowberg
+
+Permission is hereby granted, free of charge, to any person obtaining a copy
+of this software and associated documentation files (the "Software"), to deal
+in the Software without restriction, including without limitation the rights
+to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+copies of the Software, and to permit persons to whom the Software is
+furnished to do so, subject to the following conditions:
+
+The above copyright notice and this permission notice shall be included in
+all copies or substantial portions of the Software.
+
+THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+THE SOFTWARE.
+===============================================
+*/
+
+#ifndef _MPU6050_H_
+#define _MPU6050_H_
+
+#include "I2Cdev.h"
+
+// supporting link: http://forum.arduino.cc/index.php?&topic=143444.msg1079517#msg1079517
+// also: http://forum.arduino.cc/index.php?&topic=141571.msg1062899#msg1062899s
+
+#ifdef __AVR__
+#include
+#elif defined(ARDUINO_ARCH_SAMD)
+#include
+#else
+//#define PROGMEM /* empty */
+//#define pgm_read_byte(x) (*(x))
+//#define pgm_read_word(x) (*(x))
+//#define pgm_read_float(x) (*(x))
+//#define PSTR(STR) STR
+#endif
+
+
+#define MPU6050_ADDRESS_AD0_LOW 0x68 // address pin low (GND), default for InvenSense evaluation board
+#define MPU6050_ADDRESS_AD0_HIGH 0x69 // address pin high (VCC)
+#define MPU6050_DEFAULT_ADDRESS MPU6050_ADDRESS_AD0_LOW
+
+#define MPU6050_RA_XG_OFFS_TC 0x00 //[7] PWR_MODE, [6:1] XG_OFFS_TC, [0] OTP_BNK_VLD
+#define MPU6050_RA_YG_OFFS_TC 0x01 //[7] PWR_MODE, [6:1] YG_OFFS_TC, [0] OTP_BNK_VLD
+#define MPU6050_RA_ZG_OFFS_TC 0x02 //[7] PWR_MODE, [6:1] ZG_OFFS_TC, [0] OTP_BNK_VLD
+#define MPU6050_RA_X_FINE_GAIN 0x03 //[7:0] X_FINE_GAIN
+#define MPU6050_RA_Y_FINE_GAIN 0x04 //[7:0] Y_FINE_GAIN
+#define MPU6050_RA_Z_FINE_GAIN 0x05 //[7:0] Z_FINE_GAIN
+#define MPU6050_RA_XA_OFFS_H 0x06 //[15:0] XA_OFFS
+#define MPU6050_RA_XA_OFFS_L_TC 0x07
+#define MPU6050_RA_YA_OFFS_H 0x08 //[15:0] YA_OFFS
+#define MPU6050_RA_YA_OFFS_L_TC 0x09
+#define MPU6050_RA_ZA_OFFS_H 0x0A //[15:0] ZA_OFFS
+#define MPU6050_RA_ZA_OFFS_L_TC 0x0B
+#define MPU6050_RA_SELF_TEST_X 0x0D //[7:5] XA_TEST[4-2], [4:0] XG_TEST[4-0]
+#define MPU6050_RA_SELF_TEST_Y 0x0E //[7:5] YA_TEST[4-2], [4:0] YG_TEST[4-0]
+#define MPU6050_RA_SELF_TEST_Z 0x0F //[7:5] ZA_TEST[4-2], [4:0] ZG_TEST[4-0]
+#define MPU6050_RA_SELF_TEST_A 0x10 //[5:4] XA_TEST[1-0], [3:2] YA_TEST[1-0], [1:0] ZA_TEST[1-0]
+#define MPU6050_RA_XG_OFFS_USRH 0x13 //[15:0] XG_OFFS_USR
+#define MPU6050_RA_XG_OFFS_USRL 0x14
+#define MPU6050_RA_YG_OFFS_USRH 0x15 //[15:0] YG_OFFS_USR
+#define MPU6050_RA_YG_OFFS_USRL 0x16
+#define MPU6050_RA_ZG_OFFS_USRH 0x17 //[15:0] ZG_OFFS_USR
+#define MPU6050_RA_ZG_OFFS_USRL 0x18
+#define MPU6050_RA_SMPLRT_DIV 0x19
+#define MPU6050_RA_CONFIG 0x1A
+#define MPU6050_RA_GYRO_CONFIG 0x1B
+#define MPU6050_RA_ACCEL_CONFIG 0x1C
+#define MPU6050_RA_FF_THR 0x1D
+#define MPU6050_RA_FF_DUR 0x1E
+#define MPU6050_RA_MOT_THR 0x1F
+#define MPU6050_RA_MOT_DUR 0x20
+#define MPU6050_RA_ZRMOT_THR 0x21
+#define MPU6050_RA_ZRMOT_DUR 0x22
+#define MPU6050_RA_FIFO_EN 0x23
+#define MPU6050_RA_I2C_MST_CTRL 0x24
+#define MPU6050_RA_I2C_SLV0_ADDR 0x25
+#define MPU6050_RA_I2C_SLV0_REG 0x26
+#define MPU6050_RA_I2C_SLV0_CTRL 0x27
+#define MPU6050_RA_I2C_SLV1_ADDR 0x28
+#define MPU6050_RA_I2C_SLV1_REG 0x29
+#define MPU6050_RA_I2C_SLV1_CTRL 0x2A
+#define MPU6050_RA_I2C_SLV2_ADDR 0x2B
+#define MPU6050_RA_I2C_SLV2_REG 0x2C
+#define MPU6050_RA_I2C_SLV2_CTRL 0x2D
+#define MPU6050_RA_I2C_SLV3_ADDR 0x2E
+#define MPU6050_RA_I2C_SLV3_REG 0x2F
+#define MPU6050_RA_I2C_SLV3_CTRL 0x30
+#define MPU6050_RA_I2C_SLV4_ADDR 0x31
+#define MPU6050_RA_I2C_SLV4_REG 0x32
+#define MPU6050_RA_I2C_SLV4_DO 0x33
+#define MPU6050_RA_I2C_SLV4_CTRL 0x34
+#define MPU6050_RA_I2C_SLV4_DI 0x35
+#define MPU6050_RA_I2C_MST_STATUS 0x36
+#define MPU6050_RA_INT_PIN_CFG 0x37
+#define MPU6050_RA_INT_ENABLE 0x38
+#define MPU6050_RA_DMP_INT_STATUS 0x39
+#define MPU6050_RA_INT_STATUS 0x3A
+#define MPU6050_RA_ACCEL_XOUT_H 0x3B
+#define MPU6050_RA_ACCEL_XOUT_L 0x3C
+#define MPU6050_RA_ACCEL_YOUT_H 0x3D
+#define MPU6050_RA_ACCEL_YOUT_L 0x3E
+#define MPU6050_RA_ACCEL_ZOUT_H 0x3F
+#define MPU6050_RA_ACCEL_ZOUT_L 0x40
+#define MPU6050_RA_TEMP_OUT_H 0x41
+#define MPU6050_RA_TEMP_OUT_L 0x42
+#define MPU6050_RA_GYRO_XOUT_H 0x43
+#define MPU6050_RA_GYRO_XOUT_L 0x44
+#define MPU6050_RA_GYRO_YOUT_H 0x45
+#define MPU6050_RA_GYRO_YOUT_L 0x46
+#define MPU6050_RA_GYRO_ZOUT_H 0x47
+#define MPU6050_RA_GYRO_ZOUT_L 0x48
+#define MPU6050_RA_EXT_SENS_DATA_00 0x49
+#define MPU6050_RA_EXT_SENS_DATA_01 0x4A
+#define MPU6050_RA_EXT_SENS_DATA_02 0x4B
+#define MPU6050_RA_EXT_SENS_DATA_03 0x4C
+#define MPU6050_RA_EXT_SENS_DATA_04 0x4D
+#define MPU6050_RA_EXT_SENS_DATA_05 0x4E
+#define MPU6050_RA_EXT_SENS_DATA_06 0x4F
+#define MPU6050_RA_EXT_SENS_DATA_07 0x50
+#define MPU6050_RA_EXT_SENS_DATA_08 0x51
+#define MPU6050_RA_EXT_SENS_DATA_09 0x52
+#define MPU6050_RA_EXT_SENS_DATA_10 0x53
+#define MPU6050_RA_EXT_SENS_DATA_11 0x54
+#define MPU6050_RA_EXT_SENS_DATA_12 0x55
+#define MPU6050_RA_EXT_SENS_DATA_13 0x56
+#define MPU6050_RA_EXT_SENS_DATA_14 0x57
+#define MPU6050_RA_EXT_SENS_DATA_15 0x58
+#define MPU6050_RA_EXT_SENS_DATA_16 0x59
+#define MPU6050_RA_EXT_SENS_DATA_17 0x5A
+#define MPU6050_RA_EXT_SENS_DATA_18 0x5B
+#define MPU6050_RA_EXT_SENS_DATA_19 0x5C
+#define MPU6050_RA_EXT_SENS_DATA_20 0x5D
+#define MPU6050_RA_EXT_SENS_DATA_21 0x5E
+#define MPU6050_RA_EXT_SENS_DATA_22 0x5F
+#define MPU6050_RA_EXT_SENS_DATA_23 0x60
+#define MPU6050_RA_MOT_DETECT_STATUS 0x61
+#define MPU6050_RA_I2C_SLV0_DO 0x63
+#define MPU6050_RA_I2C_SLV1_DO 0x64
+#define MPU6050_RA_I2C_SLV2_DO 0x65
+#define MPU6050_RA_I2C_SLV3_DO 0x66
+#define MPU6050_RA_I2C_MST_DELAY_CTRL 0x67
+#define MPU6050_RA_SIGNAL_PATH_RESET 0x68
+#define MPU6050_RA_MOT_DETECT_CTRL 0x69
+#define MPU6050_RA_USER_CTRL 0x6A
+#define MPU6050_RA_PWR_MGMT_1 0x6B
+#define MPU6050_RA_PWR_MGMT_2 0x6C
+#define MPU6050_RA_BANK_SEL 0x6D
+#define MPU6050_RA_MEM_START_ADDR 0x6E
+#define MPU6050_RA_MEM_R_W 0x6F
+#define MPU6050_RA_DMP_CFG_1 0x70
+#define MPU6050_RA_DMP_CFG_2 0x71
+#define MPU6050_RA_FIFO_COUNTH 0x72
+#define MPU6050_RA_FIFO_COUNTL 0x73
+#define MPU6050_RA_FIFO_R_W 0x74
+#define MPU6050_RA_WHO_AM_I 0x75
+
+#define MPU6050_SELF_TEST_XA_1_BIT 0x07
+#define MPU6050_SELF_TEST_XA_1_LENGTH 0x03
+#define MPU6050_SELF_TEST_XA_2_BIT 0x05
+#define MPU6050_SELF_TEST_XA_2_LENGTH 0x02
+#define MPU6050_SELF_TEST_YA_1_BIT 0x07
+#define MPU6050_SELF_TEST_YA_1_LENGTH 0x03
+#define MPU6050_SELF_TEST_YA_2_BIT 0x03
+#define MPU6050_SELF_TEST_YA_2_LENGTH 0x02
+#define MPU6050_SELF_TEST_ZA_1_BIT 0x07
+#define MPU6050_SELF_TEST_ZA_1_LENGTH 0x03
+#define MPU6050_SELF_TEST_ZA_2_BIT 0x01
+#define MPU6050_SELF_TEST_ZA_2_LENGTH 0x02
+
+#define MPU6050_SELF_TEST_XG_1_BIT 0x04
+#define MPU6050_SELF_TEST_XG_1_LENGTH 0x05
+#define MPU6050_SELF_TEST_YG_1_BIT 0x04
+#define MPU6050_SELF_TEST_YG_1_LENGTH 0x05
+#define MPU6050_SELF_TEST_ZG_1_BIT 0x04
+#define MPU6050_SELF_TEST_ZG_1_LENGTH 0x05
+
+#define MPU6050_TC_PWR_MODE_BIT 7
+#define MPU6050_TC_OFFSET_BIT 6
+#define MPU6050_TC_OFFSET_LENGTH 6
+#define MPU6050_TC_OTP_BNK_VLD_BIT 0
+
+#define MPU6050_VDDIO_LEVEL_VLOGIC 0
+#define MPU6050_VDDIO_LEVEL_VDD 1
+
+#define MPU6050_CFG_EXT_SYNC_SET_BIT 5
+#define MPU6050_CFG_EXT_SYNC_SET_LENGTH 3
+#define MPU6050_CFG_DLPF_CFG_BIT 2
+#define MPU6050_CFG_DLPF_CFG_LENGTH 3
+
+#define MPU6050_EXT_SYNC_DISABLED 0x0
+#define MPU6050_EXT_SYNC_TEMP_OUT_L 0x1
+#define MPU6050_EXT_SYNC_GYRO_XOUT_L 0x2
+#define MPU6050_EXT_SYNC_GYRO_YOUT_L 0x3
+#define MPU6050_EXT_SYNC_GYRO_ZOUT_L 0x4
+#define MPU6050_EXT_SYNC_ACCEL_XOUT_L 0x5
+#define MPU6050_EXT_SYNC_ACCEL_YOUT_L 0x6
+#define MPU6050_EXT_SYNC_ACCEL_ZOUT_L 0x7
+
+#define MPU6050_DLPF_BW_256 0x00
+#define MPU6050_DLPF_BW_188 0x01
+#define MPU6050_DLPF_BW_98 0x02
+#define MPU6050_DLPF_BW_42 0x03
+#define MPU6050_DLPF_BW_20 0x04
+#define MPU6050_DLPF_BW_10 0x05
+#define MPU6050_DLPF_BW_5 0x06
+
+#define MPU6050_GCONFIG_FS_SEL_BIT 4
+#define MPU6050_GCONFIG_FS_SEL_LENGTH 2
+
+#define MPU6050_GYRO_FS_250 0x00
+#define MPU6050_GYRO_FS_500 0x01
+#define MPU6050_GYRO_FS_1000 0x02
+#define MPU6050_GYRO_FS_2000 0x03
+
+#define MPU6050_ACONFIG_XA_ST_BIT 7
+#define MPU6050_ACONFIG_YA_ST_BIT 6
+#define MPU6050_ACONFIG_ZA_ST_BIT 5
+#define MPU6050_ACONFIG_AFS_SEL_BIT 4
+#define MPU6050_ACONFIG_AFS_SEL_LENGTH 2
+#define MPU6050_ACONFIG_ACCEL_HPF_BIT 2
+#define MPU6050_ACONFIG_ACCEL_HPF_LENGTH 3
+
+#define MPU6050_ACCEL_FS_2 0x00
+#define MPU6050_ACCEL_FS_4 0x01
+#define MPU6050_ACCEL_FS_8 0x02
+#define MPU6050_ACCEL_FS_16 0x03
+
+#define MPU6050_DHPF_RESET 0x00
+#define MPU6050_DHPF_5 0x01
+#define MPU6050_DHPF_2P5 0x02
+#define MPU6050_DHPF_1P25 0x03
+#define MPU6050_DHPF_0P63 0x04
+#define MPU6050_DHPF_HOLD 0x07
+
+#define MPU6050_TEMP_FIFO_EN_BIT 7
+#define MPU6050_XG_FIFO_EN_BIT 6
+#define MPU6050_YG_FIFO_EN_BIT 5
+#define MPU6050_ZG_FIFO_EN_BIT 4
+#define MPU6050_ACCEL_FIFO_EN_BIT 3
+#define MPU6050_SLV2_FIFO_EN_BIT 2
+#define MPU6050_SLV1_FIFO_EN_BIT 1
+#define MPU6050_SLV0_FIFO_EN_BIT 0
+
+#define MPU6050_MULT_MST_EN_BIT 7
+#define MPU6050_WAIT_FOR_ES_BIT 6
+#define MPU6050_SLV_3_FIFO_EN_BIT 5
+#define MPU6050_I2C_MST_P_NSR_BIT 4
+#define MPU6050_I2C_MST_CLK_BIT 3
+#define MPU6050_I2C_MST_CLK_LENGTH 4
+
+#define MPU6050_CLOCK_DIV_348 0x0
+#define MPU6050_CLOCK_DIV_333 0x1
+#define MPU6050_CLOCK_DIV_320 0x2
+#define MPU6050_CLOCK_DIV_308 0x3
+#define MPU6050_CLOCK_DIV_296 0x4
+#define MPU6050_CLOCK_DIV_286 0x5
+#define MPU6050_CLOCK_DIV_276 0x6
+#define MPU6050_CLOCK_DIV_267 0x7
+#define MPU6050_CLOCK_DIV_258 0x8
+#define MPU6050_CLOCK_DIV_500 0x9
+#define MPU6050_CLOCK_DIV_471 0xA
+#define MPU6050_CLOCK_DIV_444 0xB
+#define MPU6050_CLOCK_DIV_421 0xC
+#define MPU6050_CLOCK_DIV_400 0xD
+#define MPU6050_CLOCK_DIV_381 0xE
+#define MPU6050_CLOCK_DIV_364 0xF
+
+#define MPU6050_I2C_SLV_RW_BIT 7
+#define MPU6050_I2C_SLV_ADDR_BIT 6
+#define MPU6050_I2C_SLV_ADDR_LENGTH 7
+#define MPU6050_I2C_SLV_EN_BIT 7
+#define MPU6050_I2C_SLV_BYTE_SW_BIT 6
+#define MPU6050_I2C_SLV_REG_DIS_BIT 5
+#define MPU6050_I2C_SLV_GRP_BIT 4
+#define MPU6050_I2C_SLV_LEN_BIT 3
+#define MPU6050_I2C_SLV_LEN_LENGTH 4
+
+#define MPU6050_I2C_SLV4_RW_BIT 7
+#define MPU6050_I2C_SLV4_ADDR_BIT 6
+#define MPU6050_I2C_SLV4_ADDR_LENGTH 7
+#define MPU6050_I2C_SLV4_EN_BIT 7
+#define MPU6050_I2C_SLV4_INT_EN_BIT 6
+#define MPU6050_I2C_SLV4_REG_DIS_BIT 5
+#define MPU6050_I2C_SLV4_MST_DLY_BIT 4
+#define MPU6050_I2C_SLV4_MST_DLY_LENGTH 5
+
+#define MPU6050_MST_PASS_THROUGH_BIT 7
+#define MPU6050_MST_I2C_SLV4_DONE_BIT 6
+#define MPU6050_MST_I2C_LOST_ARB_BIT 5
+#define MPU6050_MST_I2C_SLV4_NACK_BIT 4
+#define MPU6050_MST_I2C_SLV3_NACK_BIT 3
+#define MPU6050_MST_I2C_SLV2_NACK_BIT 2
+#define MPU6050_MST_I2C_SLV1_NACK_BIT 1
+#define MPU6050_MST_I2C_SLV0_NACK_BIT 0
+
+#define MPU6050_INTCFG_INT_LEVEL_BIT 7
+#define MPU6050_INTCFG_INT_OPEN_BIT 6
+#define MPU6050_INTCFG_LATCH_INT_EN_BIT 5
+#define MPU6050_INTCFG_INT_RD_CLEAR_BIT 4
+#define MPU6050_INTCFG_FSYNC_INT_LEVEL_BIT 3
+#define MPU6050_INTCFG_FSYNC_INT_EN_BIT 2
+#define MPU6050_INTCFG_I2C_BYPASS_EN_BIT 1
+#define MPU6050_INTCFG_CLKOUT_EN_BIT 0
+
+#define MPU6050_INTMODE_ACTIVEHIGH 0x00
+#define MPU6050_INTMODE_ACTIVELOW 0x01
+
+#define MPU6050_INTDRV_PUSHPULL 0x00
+#define MPU6050_INTDRV_OPENDRAIN 0x01
+
+#define MPU6050_INTLATCH_50USPULSE 0x00
+#define MPU6050_INTLATCH_WAITCLEAR 0x01
+
+#define MPU6050_INTCLEAR_STATUSREAD 0x00
+#define MPU6050_INTCLEAR_ANYREAD 0x01
+
+#define MPU6050_INTERRUPT_FF_BIT 7
+#define MPU6050_INTERRUPT_MOT_BIT 6
+#define MPU6050_INTERRUPT_ZMOT_BIT 5
+#define MPU6050_INTERRUPT_FIFO_OFLOW_BIT 4
+#define MPU6050_INTERRUPT_I2C_MST_INT_BIT 3
+#define MPU6050_INTERRUPT_PLL_RDY_INT_BIT 2
+#define MPU6050_INTERRUPT_DMP_INT_BIT 1
+#define MPU6050_INTERRUPT_DATA_RDY_BIT 0
+
+// TODO: figure out what these actually do
+// UMPL source code is not very obivous
+#define MPU6050_DMPINT_5_BIT 5
+#define MPU6050_DMPINT_4_BIT 4
+#define MPU6050_DMPINT_3_BIT 3
+#define MPU6050_DMPINT_2_BIT 2
+#define MPU6050_DMPINT_1_BIT 1
+#define MPU6050_DMPINT_0_BIT 0
+
+#define MPU6050_MOTION_MOT_XNEG_BIT 7
+#define MPU6050_MOTION_MOT_XPOS_BIT 6
+#define MPU6050_MOTION_MOT_YNEG_BIT 5
+#define MPU6050_MOTION_MOT_YPOS_BIT 4
+#define MPU6050_MOTION_MOT_ZNEG_BIT 3
+#define MPU6050_MOTION_MOT_ZPOS_BIT 2
+#define MPU6050_MOTION_MOT_ZRMOT_BIT 0
+
+#define MPU6050_DELAYCTRL_DELAY_ES_SHADOW_BIT 7
+#define MPU6050_DELAYCTRL_I2C_SLV4_DLY_EN_BIT 4
+#define MPU6050_DELAYCTRL_I2C_SLV3_DLY_EN_BIT 3
+#define MPU6050_DELAYCTRL_I2C_SLV2_DLY_EN_BIT 2
+#define MPU6050_DELAYCTRL_I2C_SLV1_DLY_EN_BIT 1
+#define MPU6050_DELAYCTRL_I2C_SLV0_DLY_EN_BIT 0
+
+#define MPU6050_PATHRESET_GYRO_RESET_BIT 2
+#define MPU6050_PATHRESET_ACCEL_RESET_BIT 1
+#define MPU6050_PATHRESET_TEMP_RESET_BIT 0
+
+#define MPU6050_DETECT_ACCEL_ON_DELAY_BIT 5
+#define MPU6050_DETECT_ACCEL_ON_DELAY_LENGTH 2
+#define MPU6050_DETECT_FF_COUNT_BIT 3
+#define MPU6050_DETECT_FF_COUNT_LENGTH 2
+#define MPU6050_DETECT_MOT_COUNT_BIT 1
+#define MPU6050_DETECT_MOT_COUNT_LENGTH 2
+
+#define MPU6050_DETECT_DECREMENT_RESET 0x0
+#define MPU6050_DETECT_DECREMENT_1 0x1
+#define MPU6050_DETECT_DECREMENT_2 0x2
+#define MPU6050_DETECT_DECREMENT_4 0x3
+
+#define MPU6050_USERCTRL_DMP_EN_BIT 7
+#define MPU6050_USERCTRL_FIFO_EN_BIT 6
+#define MPU6050_USERCTRL_I2C_MST_EN_BIT 5
+#define MPU6050_USERCTRL_I2C_IF_DIS_BIT 4
+#define MPU6050_USERCTRL_DMP_RESET_BIT 3
+#define MPU6050_USERCTRL_FIFO_RESET_BIT 2
+#define MPU6050_USERCTRL_I2C_MST_RESET_BIT 1
+#define MPU6050_USERCTRL_SIG_COND_RESET_BIT 0
+
+#define MPU6050_PWR1_DEVICE_RESET_BIT 7
+#define MPU6050_PWR1_SLEEP_BIT 6
+#define MPU6050_PWR1_CYCLE_BIT 5
+#define MPU6050_PWR1_TEMP_DIS_BIT 3
+#define MPU6050_PWR1_CLKSEL_BIT 2
+#define MPU6050_PWR1_CLKSEL_LENGTH 3
+
+#define MPU6050_CLOCK_INTERNAL 0x00
+#define MPU6050_CLOCK_PLL_XGYRO 0x01
+#define MPU6050_CLOCK_PLL_YGYRO 0x02
+#define MPU6050_CLOCK_PLL_ZGYRO 0x03
+#define MPU6050_CLOCK_PLL_EXT32K 0x04
+#define MPU6050_CLOCK_PLL_EXT19M 0x05
+#define MPU6050_CLOCK_KEEP_RESET 0x07
+
+#define MPU6050_PWR2_LP_WAKE_CTRL_BIT 7
+#define MPU6050_PWR2_LP_WAKE_CTRL_LENGTH 2
+#define MPU6050_PWR2_STBY_XA_BIT 5
+#define MPU6050_PWR2_STBY_YA_BIT 4
+#define MPU6050_PWR2_STBY_ZA_BIT 3
+#define MPU6050_PWR2_STBY_XG_BIT 2
+#define MPU6050_PWR2_STBY_YG_BIT 1
+#define MPU6050_PWR2_STBY_ZG_BIT 0
+
+#define MPU6050_WAKE_FREQ_1P25 0x0
+#define MPU6050_WAKE_FREQ_2P5 0x1
+#define MPU6050_WAKE_FREQ_5 0x2
+#define MPU6050_WAKE_FREQ_10 0x3
+
+#define MPU6050_BANKSEL_PRFTCH_EN_BIT 6
+#define MPU6050_BANKSEL_CFG_USER_BANK_BIT 5
+#define MPU6050_BANKSEL_MEM_SEL_BIT 4
+#define MPU6050_BANKSEL_MEM_SEL_LENGTH 5
+
+#define MPU6050_WHO_AM_I_BIT 6
+#define MPU6050_WHO_AM_I_LENGTH 6
+
+#define MPU6050_DMP_MEMORY_BANKS 8
+#define MPU6050_DMP_MEMORY_BANK_SIZE 256
+#define MPU6050_DMP_MEMORY_CHUNK_SIZE 16
+
+// note: DMP code memory blocks defined at end of header file
+
+class MPU6050 {
+ public:
+ MPU6050(uint8_t address=MPU6050_DEFAULT_ADDRESS);
+
+ void initialize();
+ bool testConnection();
+
+ // AUX_VDDIO register
+ uint8_t getAuxVDDIOLevel();
+ void setAuxVDDIOLevel(uint8_t level);
+
+ // SMPLRT_DIV register
+ uint8_t getRate();
+ void setRate(uint8_t rate);
+
+ // CONFIG register
+ uint8_t getExternalFrameSync();
+ void setExternalFrameSync(uint8_t sync);
+ uint8_t getDLPFMode();
+ void setDLPFMode(uint8_t bandwidth);
+
+ // GYRO_CONFIG register
+ uint8_t getFullScaleGyroRange();
+ void setFullScaleGyroRange(uint8_t range);
+
+ // SELF_TEST registers
+ uint8_t getAccelXSelfTestFactoryTrim();
+ uint8_t getAccelYSelfTestFactoryTrim();
+ uint8_t getAccelZSelfTestFactoryTrim();
+
+ uint8_t getGyroXSelfTestFactoryTrim();
+ uint8_t getGyroYSelfTestFactoryTrim();
+ uint8_t getGyroZSelfTestFactoryTrim();
+
+ // ACCEL_CONFIG register
+ bool getAccelXSelfTest();
+ void setAccelXSelfTest(bool enabled);
+ bool getAccelYSelfTest();
+ void setAccelYSelfTest(bool enabled);
+ bool getAccelZSelfTest();
+ void setAccelZSelfTest(bool enabled);
+ uint8_t getFullScaleAccelRange();
+ void setFullScaleAccelRange(uint8_t range);
+ uint8_t getDHPFMode();
+ void setDHPFMode(uint8_t mode);
+
+ // FF_THR register
+ uint8_t getFreefallDetectionThreshold();
+ void setFreefallDetectionThreshold(uint8_t threshold);
+
+ // FF_DUR register
+ uint8_t getFreefallDetectionDuration();
+ void setFreefallDetectionDuration(uint8_t duration);
+
+ // MOT_THR register
+ uint8_t getMotionDetectionThreshold();
+ void setMotionDetectionThreshold(uint8_t threshold);
+
+ // MOT_DUR register
+ uint8_t getMotionDetectionDuration();
+ void setMotionDetectionDuration(uint8_t duration);
+
+ // ZRMOT_THR register
+ uint8_t getZeroMotionDetectionThreshold();
+ void setZeroMotionDetectionThreshold(uint8_t threshold);
+
+ // ZRMOT_DUR register
+ uint8_t getZeroMotionDetectionDuration();
+ void setZeroMotionDetectionDuration(uint8_t duration);
+
+ // FIFO_EN register
+ bool getTempFIFOEnabled();
+ void setTempFIFOEnabled(bool enabled);
+ bool getXGyroFIFOEnabled();
+ void setXGyroFIFOEnabled(bool enabled);
+ bool getYGyroFIFOEnabled();
+ void setYGyroFIFOEnabled(bool enabled);
+ bool getZGyroFIFOEnabled();
+ void setZGyroFIFOEnabled(bool enabled);
+ bool getAccelFIFOEnabled();
+ void setAccelFIFOEnabled(bool enabled);
+ bool getSlave2FIFOEnabled();
+ void setSlave2FIFOEnabled(bool enabled);
+ bool getSlave1FIFOEnabled();
+ void setSlave1FIFOEnabled(bool enabled);
+ bool getSlave0FIFOEnabled();
+ void setSlave0FIFOEnabled(bool enabled);
+
+ // I2C_MST_CTRL register
+ bool getMultiMasterEnabled();
+ void setMultiMasterEnabled(bool enabled);
+ bool getWaitForExternalSensorEnabled();
+ void setWaitForExternalSensorEnabled(bool enabled);
+ bool getSlave3FIFOEnabled();
+ void setSlave3FIFOEnabled(bool enabled);
+ bool getSlaveReadWriteTransitionEnabled();
+ void setSlaveReadWriteTransitionEnabled(bool enabled);
+ uint8_t getMasterClockSpeed();
+ void setMasterClockSpeed(uint8_t speed);
+
+ // I2C_SLV* registers (Slave 0-3)
+ uint8_t getSlaveAddress(uint8_t num);
+ void setSlaveAddress(uint8_t num, uint8_t address);
+ uint8_t getSlaveRegister(uint8_t num);
+ void setSlaveRegister(uint8_t num, uint8_t reg);
+ bool getSlaveEnabled(uint8_t num);
+ void setSlaveEnabled(uint8_t num, bool enabled);
+ bool getSlaveWordByteSwap(uint8_t num);
+ void setSlaveWordByteSwap(uint8_t num, bool enabled);
+ bool getSlaveWriteMode(uint8_t num);
+ void setSlaveWriteMode(uint8_t num, bool mode);
+ bool getSlaveWordGroupOffset(uint8_t num);
+ void setSlaveWordGroupOffset(uint8_t num, bool enabled);
+ uint8_t getSlaveDataLength(uint8_t num);
+ void setSlaveDataLength(uint8_t num, uint8_t length);
+
+ // I2C_SLV* registers (Slave 4)
+ uint8_t getSlave4Address();
+ void setSlave4Address(uint8_t address);
+ uint8_t getSlave4Register();
+ void setSlave4Register(uint8_t reg);
+ void setSlave4OutputByte(uint8_t data);
+ bool getSlave4Enabled();
+ void setSlave4Enabled(bool enabled);
+ bool getSlave4InterruptEnabled();
+ void setSlave4InterruptEnabled(bool enabled);
+ bool getSlave4WriteMode();
+ void setSlave4WriteMode(bool mode);
+ uint8_t getSlave4MasterDelay();
+ void setSlave4MasterDelay(uint8_t delay);
+ uint8_t getSlate4InputByte();
+
+ // I2C_MST_STATUS register
+ bool getPassthroughStatus();
+ bool getSlave4IsDone();
+ bool getLostArbitration();
+ bool getSlave4Nack();
+ bool getSlave3Nack();
+ bool getSlave2Nack();
+ bool getSlave1Nack();
+ bool getSlave0Nack();
+
+ // INT_PIN_CFG register
+ bool getInterruptMode();
+ void setInterruptMode(bool mode);
+ bool getInterruptDrive();
+ void setInterruptDrive(bool drive);
+ bool getInterruptLatch();
+ void setInterruptLatch(bool latch);
+ bool getInterruptLatchClear();
+ void setInterruptLatchClear(bool clear);
+ bool getFSyncInterruptLevel();
+ void setFSyncInterruptLevel(bool level);
+ bool getFSyncInterruptEnabled();
+ void setFSyncInterruptEnabled(bool enabled);
+ bool getI2CBypassEnabled();
+ void setI2CBypassEnabled(bool enabled);
+ bool getClockOutputEnabled();
+ void setClockOutputEnabled(bool enabled);
+
+ // INT_ENABLE register
+ uint8_t getIntEnabled();
+ void setIntEnabled(uint8_t enabled);
+ bool getIntFreefallEnabled();
+ void setIntFreefallEnabled(bool enabled);
+ bool getIntMotionEnabled();
+ void setIntMotionEnabled(bool enabled);
+ bool getIntZeroMotionEnabled();
+ void setIntZeroMotionEnabled(bool enabled);
+ bool getIntFIFOBufferOverflowEnabled();
+ void setIntFIFOBufferOverflowEnabled(bool enabled);
+ bool getIntI2CMasterEnabled();
+ void setIntI2CMasterEnabled(bool enabled);
+ bool getIntDataReadyEnabled();
+ void setIntDataReadyEnabled(bool enabled);
+
+ // INT_STATUS register
+ uint8_t getIntStatus();
+ bool getIntFreefallStatus();
+ bool getIntMotionStatus();
+ bool getIntZeroMotionStatus();
+ bool getIntFIFOBufferOverflowStatus();
+ bool getIntI2CMasterStatus();
+ bool getIntDataReadyStatus();
+
+ // ACCEL_*OUT_* registers
+ void getMotion9(int16_t* ax, int16_t* ay, int16_t* az, int16_t* gx, int16_t* gy, int16_t* gz, int16_t* mx, int16_t* my, int16_t* mz);
+ void getMotion6(int16_t* ax, int16_t* ay, int16_t* az, int16_t* gx, int16_t* gy, int16_t* gz);
+ void getAcceleration(int16_t* x, int16_t* y, int16_t* z);
+ int16_t getAccelerationX();
+ int16_t getAccelerationY();
+ int16_t getAccelerationZ();
+
+ // TEMP_OUT_* registers
+ int16_t getTemperature();
+
+ // GYRO_*OUT_* registers
+ void getRotation(int16_t* x, int16_t* y, int16_t* z);
+ int16_t getRotationX();
+ int16_t getRotationY();
+ int16_t getRotationZ();
+
+ // EXT_SENS_DATA_* registers
+ uint8_t getExternalSensorByte(int position);
+ uint16_t getExternalSensorWord(int position);
+ uint32_t getExternalSensorDWord(int position);
+
+ // MOT_DETECT_STATUS register
+ uint8_t getMotionStatus();
+ bool getXNegMotionDetected();
+ bool getXPosMotionDetected();
+ bool getYNegMotionDetected();
+ bool getYPosMotionDetected();
+ bool getZNegMotionDetected();
+ bool getZPosMotionDetected();
+ bool getZeroMotionDetected();
+
+ // I2C_SLV*_DO register
+ void setSlaveOutputByte(uint8_t num, uint8_t data);
+
+ // I2C_MST_DELAY_CTRL register
+ bool getExternalShadowDelayEnabled();
+ void setExternalShadowDelayEnabled(bool enabled);
+ bool getSlaveDelayEnabled(uint8_t num);
+ void setSlaveDelayEnabled(uint8_t num, bool enabled);
+
+ // SIGNAL_PATH_RESET register
+ void resetGyroscopePath();
+ void resetAccelerometerPath();
+ void resetTemperaturePath();
+
+ // MOT_DETECT_CTRL register
+ uint8_t getAccelerometerPowerOnDelay();
+ void setAccelerometerPowerOnDelay(uint8_t delay);
+ uint8_t getFreefallDetectionCounterDecrement();
+ void setFreefallDetectionCounterDecrement(uint8_t decrement);
+ uint8_t getMotionDetectionCounterDecrement();
+ void setMotionDetectionCounterDecrement(uint8_t decrement);
+
+ // USER_CTRL register
+ bool getFIFOEnabled();
+ void setFIFOEnabled(bool enabled);
+ bool getI2CMasterModeEnabled();
+ void setI2CMasterModeEnabled(bool enabled);
+ void switchSPIEnabled(bool enabled);
+ void resetFIFO();
+ void resetI2CMaster();
+ void resetSensors();
+
+ // PWR_MGMT_1 register
+ void reset();
+ bool getSleepEnabled();
+ void setSleepEnabled(bool enabled);
+ bool getWakeCycleEnabled();
+ void setWakeCycleEnabled(bool enabled);
+ bool getTempSensorEnabled();
+ void setTempSensorEnabled(bool enabled);
+ uint8_t getClockSource();
+ void setClockSource(uint8_t source);
+
+ // PWR_MGMT_2 register
+ uint8_t getWakeFrequency();
+ void setWakeFrequency(uint8_t frequency);
+ bool getStandbyXAccelEnabled();
+ void setStandbyXAccelEnabled(bool enabled);
+ bool getStandbyYAccelEnabled();
+ void setStandbyYAccelEnabled(bool enabled);
+ bool getStandbyZAccelEnabled();
+ void setStandbyZAccelEnabled(bool enabled);
+ bool getStandbyXGyroEnabled();
+ void setStandbyXGyroEnabled(bool enabled);
+ bool getStandbyYGyroEnabled();
+ void setStandbyYGyroEnabled(bool enabled);
+ bool getStandbyZGyroEnabled();
+ void setStandbyZGyroEnabled(bool enabled);
+
+ // FIFO_COUNT_* registers
+ uint16_t getFIFOCount();
+
+ // FIFO_R_W register
+ uint8_t getFIFOByte();
+ void setFIFOByte(uint8_t data);
+ void getFIFOBytes(uint8_t *data, uint8_t length);
+
+ // WHO_AM_I register
+ uint8_t getDeviceID();
+ void setDeviceID(uint8_t id);
+
+ // ======== UNDOCUMENTED/DMP REGISTERS/METHODS ========
+
+ // XG_OFFS_TC register
+ uint8_t getOTPBankValid();
+ void setOTPBankValid(bool enabled);
+ int8_t getXGyroOffsetTC();
+ void setXGyroOffsetTC(int8_t offset);
+
+ // YG_OFFS_TC register
+ int8_t getYGyroOffsetTC();
+ void setYGyroOffsetTC(int8_t offset);
+
+ // ZG_OFFS_TC register
+ int8_t getZGyroOffsetTC();
+ void setZGyroOffsetTC(int8_t offset);
+
+ // X_FINE_GAIN register
+ int8_t getXFineGain();
+ void setXFineGain(int8_t gain);
+
+ // Y_FINE_GAIN register
+ int8_t getYFineGain();
+ void setYFineGain(int8_t gain);
+
+ // Z_FINE_GAIN register
+ int8_t getZFineGain();
+ void setZFineGain(int8_t gain);
+
+ // XA_OFFS_* registers
+ int16_t getXAccelOffset();
+ void setXAccelOffset(int16_t offset);
+
+ // YA_OFFS_* register
+ int16_t getYAccelOffset();
+ void setYAccelOffset(int16_t offset);
+
+ // ZA_OFFS_* register
+ int16_t getZAccelOffset();
+ void setZAccelOffset(int16_t offset);
+
+ // XG_OFFS_USR* registers
+ int16_t getXGyroOffset();
+ void setXGyroOffset(int16_t offset);
+
+ // YG_OFFS_USR* register
+ int16_t getYGyroOffset();
+ void setYGyroOffset(int16_t offset);
+
+ // ZG_OFFS_USR* register
+ int16_t getZGyroOffset();
+ void setZGyroOffset(int16_t offset);
+
+ // INT_ENABLE register (DMP functions)
+ bool getIntPLLReadyEnabled();
+ void setIntPLLReadyEnabled(bool enabled);
+ bool getIntDMPEnabled();
+ void setIntDMPEnabled(bool enabled);
+
+ // DMP_INT_STATUS
+ bool getDMPInt5Status();
+ bool getDMPInt4Status();
+ bool getDMPInt3Status();
+ bool getDMPInt2Status();
+ bool getDMPInt1Status();
+ bool getDMPInt0Status();
+
+ // INT_STATUS register (DMP functions)
+ bool getIntPLLReadyStatus();
+ bool getIntDMPStatus();
+
+ // USER_CTRL register (DMP functions)
+ bool getDMPEnabled();
+ void setDMPEnabled(bool enabled);
+ void resetDMP();
+
+ // BANK_SEL register
+ void setMemoryBank(uint8_t bank, bool prefetchEnabled=false, bool userBank=false);
+
+ // MEM_START_ADDR register
+ void setMemoryStartAddress(uint8_t address);
+
+ // MEM_R_W register
+ uint8_t readMemoryByte();
+ void writeMemoryByte(uint8_t data);
+ void readMemoryBlock(uint8_t *data, uint16_t dataSize, uint8_t bank=0, uint8_t address=0);
+ bool writeMemoryBlock(const uint8_t *data, uint16_t dataSize, uint8_t bank=0, uint8_t address=0, bool verify=true, bool useProgMem=false);
+ bool writeProgMemoryBlock(const uint8_t *data, uint16_t dataSize, uint8_t bank=0, uint8_t address=0, bool verify=true);
+
+ bool writeDMPConfigurationSet(const uint8_t *data, uint16_t dataSize, bool useProgMem=false);
+ bool writeProgDMPConfigurationSet(const uint8_t *data, uint16_t dataSize);
+
+ // DMP_CFG_1 register
+ uint8_t getDMPConfig1();
+ void setDMPConfig1(uint8_t config);
+
+ // DMP_CFG_2 register
+ uint8_t getDMPConfig2();
+ void setDMPConfig2(uint8_t config);
+
+ // Calibration Routines
+ void CalibrateGyro(uint8_t Loops = 15); // Fine tune after setting offsets with less Loops.
+ void CalibrateAccel(uint8_t Loops = 15);// Fine tune after setting offsets with less Loops.
+ void PID(uint8_t ReadAddress, float kP,float kI, uint8_t Loops); // Does the math
+ void PrintActiveOffsets(); // See the results of the Calibration
+
+
+
+ // special methods for MotionApps 2.0 implementation
+ #ifdef MPU6050_INCLUDE_DMP_MOTIONAPPS20
+
+ uint8_t dmpInitialize();
+ bool dmpPacketAvailable();
+
+ uint8_t dmpSetFIFORate(uint8_t fifoRate);
+ uint8_t dmpGetFIFORate();
+ uint8_t dmpGetSampleStepSizeMS();
+ uint8_t dmpGetSampleFrequency();
+ int32_t dmpDecodeTemperature(int8_t tempReg);
+
+ // Register callbacks after a packet of FIFO data is processed
+ //uint8_t dmpRegisterFIFORateProcess(inv_obj_func func, int16_t priority);
+ //uint8_t dmpUnregisterFIFORateProcess(inv_obj_func func);
+ uint8_t dmpRunFIFORateProcesses();
+
+ // Setup FIFO for various output
+ uint8_t dmpSendQuaternion(uint_fast16_t accuracy);
+ uint8_t dmpSendGyro(uint_fast16_t elements, uint_fast16_t accuracy);
+ uint8_t dmpSendAccel(uint_fast16_t elements, uint_fast16_t accuracy);
+ uint8_t dmpSendLinearAccel(uint_fast16_t elements, uint_fast16_t accuracy);
+ uint8_t dmpSendLinearAccelInWorld(uint_fast16_t elements, uint_fast16_t accuracy);
+ uint8_t dmpSendControlData(uint_fast16_t elements, uint_fast16_t accuracy);
+ uint8_t dmpSendSensorData(uint_fast16_t elements, uint_fast16_t accuracy);
+ uint8_t dmpSendExternalSensorData(uint_fast16_t elements, uint_fast16_t accuracy);
+ uint8_t dmpSendGravity(uint_fast16_t elements, uint_fast16_t accuracy);
+ uint8_t dmpSendPacketNumber(uint_fast16_t accuracy);
+ uint8_t dmpSendQuantizedAccel(uint_fast16_t elements, uint_fast16_t accuracy);
+ uint8_t dmpSendEIS(uint_fast16_t elements, uint_fast16_t accuracy);
+
+ // Get Fixed Point data from FIFO
+ uint8_t dmpGetAccel(int32_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetAccel(int16_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetAccel(VectorInt16 *v, const uint8_t* packet=0);
+ uint8_t dmpGetQuaternion(int32_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetQuaternion(int16_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetQuaternion(Quaternion *q, const uint8_t* packet=0);
+ uint8_t dmpGet6AxisQuaternion(int32_t *data, const uint8_t* packet=0);
+ uint8_t dmpGet6AxisQuaternion(int16_t *data, const uint8_t* packet=0);
+ uint8_t dmpGet6AxisQuaternion(Quaternion *q, const uint8_t* packet=0);
+ uint8_t dmpGetRelativeQuaternion(int32_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetRelativeQuaternion(int16_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetRelativeQuaternion(Quaternion *data, const uint8_t* packet=0);
+ uint8_t dmpGetGyro(int32_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetGyro(int16_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetGyro(VectorInt16 *v, const uint8_t* packet=0);
+ uint8_t dmpSetLinearAccelFilterCoefficient(float coef);
+ uint8_t dmpGetLinearAccel(int32_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetLinearAccel(int16_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetLinearAccel(VectorInt16 *v, const uint8_t* packet=0);
+ uint8_t dmpGetLinearAccel(VectorInt16 *v, VectorInt16 *vRaw, VectorFloat *gravity);
+ uint8_t dmpGetLinearAccelInWorld(int32_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetLinearAccelInWorld(int16_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetLinearAccelInWorld(VectorInt16 *v, const uint8_t* packet=0);
+ uint8_t dmpGetLinearAccelInWorld(VectorInt16 *v, VectorInt16 *vReal, Quaternion *q);
+ uint8_t dmpGetGyroAndAccelSensor(int32_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetGyroAndAccelSensor(int16_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetGyroAndAccelSensor(VectorInt16 *g, VectorInt16 *a, const uint8_t* packet=0);
+ uint8_t dmpGetGyroSensor(int32_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetGyroSensor(int16_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetGyroSensor(VectorInt16 *v, const uint8_t* packet=0);
+ uint8_t dmpGetControlData(int32_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetTemperature(int32_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetGravity(int32_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetGravity(int16_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetGravity(VectorInt16 *v, const uint8_t* packet=0);
+ uint8_t dmpGetGravity(VectorFloat *v, Quaternion *q);
+ uint8_t dmpGetUnquantizedAccel(int32_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetUnquantizedAccel(int16_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetUnquantizedAccel(VectorInt16 *v, const uint8_t* packet=0);
+ uint8_t dmpGetQuantizedAccel(int32_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetQuantizedAccel(int16_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetQuantizedAccel(VectorInt16 *v, const uint8_t* packet=0);
+ uint8_t dmpGetExternalSensorData(int32_t *data, uint16_t size, const uint8_t* packet=0);
+ uint8_t dmpGetEIS(int32_t *data, const uint8_t* packet=0);
+
+ uint8_t dmpGetEuler(float *data, Quaternion *q);
+ uint8_t dmpGetYawPitchRoll(float *data, Quaternion *q, VectorFloat *gravity);
+
+ // Get Floating Point data from FIFO
+ uint8_t dmpGetAccelFloat(float *data, const uint8_t* packet=0);
+ uint8_t dmpGetQuaternionFloat(float *data, const uint8_t* packet=0);
+
+ uint8_t dmpProcessFIFOPacket(const unsigned char *dmpData);
+ uint8_t dmpReadAndProcessFIFOPacket(uint8_t numPackets, uint8_t *processed=NULL);
+
+ uint8_t dmpSetFIFOProcessedCallback(void (*func) (void));
+
+ uint8_t dmpInitFIFOParam();
+ uint8_t dmpCloseFIFO();
+ uint8_t dmpSetGyroDataSource(uint8_t source);
+ uint8_t dmpDecodeQuantizedAccel();
+ uint32_t dmpGetGyroSumOfSquare();
+ uint32_t dmpGetAccelSumOfSquare();
+ void dmpOverrideQuaternion(long *q);
+ uint16_t dmpGetFIFOPacketSize();
+ #endif
+
+ // special methods for MotionApps 4.1 implementation
+ #ifdef MPU6050_INCLUDE_DMP_MOTIONAPPS41
+
+ uint8_t dmpInitialize();
+ bool dmpPacketAvailable();
+
+ uint8_t dmpSetFIFORate(uint8_t fifoRate);
+ uint8_t dmpGetFIFORate();
+ uint8_t dmpGetSampleStepSizeMS();
+ uint8_t dmpGetSampleFrequency();
+ int32_t dmpDecodeTemperature(int8_t tempReg);
+
+ // Register callbacks after a packet of FIFO data is processed
+ //uint8_t dmpRegisterFIFORateProcess(inv_obj_func func, int16_t priority);
+ //uint8_t dmpUnregisterFIFORateProcess(inv_obj_func func);
+ uint8_t dmpRunFIFORateProcesses();
+
+ // Setup FIFO for various output
+ uint8_t dmpSendQuaternion(uint_fast16_t accuracy);
+ uint8_t dmpSendGyro(uint_fast16_t elements, uint_fast16_t accuracy);
+ uint8_t dmpSendAccel(uint_fast16_t elements, uint_fast16_t accuracy);
+ uint8_t dmpSendLinearAccel(uint_fast16_t elements, uint_fast16_t accuracy);
+ uint8_t dmpSendLinearAccelInWorld(uint_fast16_t elements, uint_fast16_t accuracy);
+ uint8_t dmpSendControlData(uint_fast16_t elements, uint_fast16_t accuracy);
+ uint8_t dmpSendSensorData(uint_fast16_t elements, uint_fast16_t accuracy);
+ uint8_t dmpSendExternalSensorData(uint_fast16_t elements, uint_fast16_t accuracy);
+ uint8_t dmpSendGravity(uint_fast16_t elements, uint_fast16_t accuracy);
+ uint8_t dmpSendPacketNumber(uint_fast16_t accuracy);
+ uint8_t dmpSendQuantizedAccel(uint_fast16_t elements, uint_fast16_t accuracy);
+ uint8_t dmpSendEIS(uint_fast16_t elements, uint_fast16_t accuracy);
+
+ // Get Fixed Point data from FIFO
+ uint8_t dmpGetAccel(int32_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetAccel(int16_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetAccel(VectorInt16 *v, const uint8_t* packet=0);
+ uint8_t dmpGetQuaternion(int32_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetQuaternion(int16_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetQuaternion(Quaternion *q, const uint8_t* packet=0);
+ uint8_t dmpGet6AxisQuaternion(int32_t *data, const uint8_t* packet=0);
+ uint8_t dmpGet6AxisQuaternion(int16_t *data, const uint8_t* packet=0);
+ uint8_t dmpGet6AxisQuaternion(Quaternion *q, const uint8_t* packet=0);
+ uint8_t dmpGetRelativeQuaternion(int32_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetRelativeQuaternion(int16_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetRelativeQuaternion(Quaternion *data, const uint8_t* packet=0);
+ uint8_t dmpGetGyro(int32_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetGyro(int16_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetGyro(VectorInt16 *v, const uint8_t* packet=0);
+ uint8_t dmpGetMag(int16_t *data, const uint8_t* packet=0);
+ uint8_t dmpSetLinearAccelFilterCoefficient(float coef);
+ uint8_t dmpGetLinearAccel(int32_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetLinearAccel(int16_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetLinearAccel(VectorInt16 *v, const uint8_t* packet=0);
+ uint8_t dmpGetLinearAccel(VectorInt16 *v, VectorInt16 *vRaw, VectorFloat *gravity);
+ uint8_t dmpGetLinearAccelInWorld(int32_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetLinearAccelInWorld(int16_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetLinearAccelInWorld(VectorInt16 *v, const uint8_t* packet=0);
+ uint8_t dmpGetLinearAccelInWorld(VectorInt16 *v, VectorInt16 *vReal, Quaternion *q);
+ uint8_t dmpGetGyroAndAccelSensor(int32_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetGyroAndAccelSensor(int16_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetGyroAndAccelSensor(VectorInt16 *g, VectorInt16 *a, const uint8_t* packet=0);
+ uint8_t dmpGetGyroSensor(int32_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetGyroSensor(int16_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetGyroSensor(VectorInt16 *v, const uint8_t* packet=0);
+ uint8_t dmpGetControlData(int32_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetTemperature(int32_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetGravity(int32_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetGravity(int16_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetGravity(VectorInt16 *v, const uint8_t* packet=0);
+ uint8_t dmpGetGravity(VectorFloat *v, Quaternion *q);
+ uint8_t dmpGetUnquantizedAccel(int32_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetUnquantizedAccel(int16_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetUnquantizedAccel(VectorInt16 *v, const uint8_t* packet=0);
+ uint8_t dmpGetQuantizedAccel(int32_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetQuantizedAccel(int16_t *data, const uint8_t* packet=0);
+ uint8_t dmpGetQuantizedAccel(VectorInt16 *v, const uint8_t* packet=0);
+ uint8_t dmpGetExternalSensorData(int32_t *data, uint16_t size, const uint8_t* packet=0);
+ uint8_t dmpGetEIS(int32_t *data, const uint8_t* packet=0);
+
+ uint8_t dmpGetEuler(float *data, Quaternion *q);
+ uint8_t dmpGetYawPitchRoll(float *data, Quaternion *q, VectorFloat *gravity);
+
+ // Get Floating Point data from FIFO
+ uint8_t dmpGetAccelFloat(float *data, const uint8_t* packet=0);
+ uint8_t dmpGetQuaternionFloat(float *data, const uint8_t* packet=0);
+
+ uint8_t dmpProcessFIFOPacket(const unsigned char *dmpData);
+ uint8_t dmpReadAndProcessFIFOPacket(uint8_t numPackets, uint8_t *processed=NULL);
+
+ uint8_t dmpSetFIFOProcessedCallback(void (*func) (void));
+
+ uint8_t dmpInitFIFOParam();
+ uint8_t dmpCloseFIFO();
+ uint8_t dmpSetGyroDataSource(uint8_t source);
+ uint8_t dmpDecodeQuantizedAccel();
+ uint32_t dmpGetGyroSumOfSquare();
+ uint32_t dmpGetAccelSumOfSquare();
+ void dmpOverrideQuaternion(long *q);
+ uint16_t dmpGetFIFOPacketSize();
+ #endif
+
+ private:
+ uint8_t devAddr;
+ uint8_t buffer[14];
+ #if defined(MPU6050_INCLUDE_DMP_MOTIONAPPS20) or defined(MPU6050_INCLUDE_DMP_MOTIONAPPS41)
+ uint8_t *dmpPacketBuffer;
+ uint16_t dmpPacketSize;
+ #endif
+};
+
+#endif /* _MPU6050_H_ */
diff --git a/Versions/dRehmFlight_ESP32_BETA_1.3/src/MPU6050/MPU6050_6Axis_MotionApps20.h b/Versions/dRehmFlight_ESP32_BETA_1.3/src/MPU6050/MPU6050_6Axis_MotionApps20.h
new file mode 100644
index 00000000..97dfdcbd
--- /dev/null
+++ b/Versions/dRehmFlight_ESP32_BETA_1.3/src/MPU6050/MPU6050_6Axis_MotionApps20.h
@@ -0,0 +1,617 @@
+// I2Cdev library collection - MPU6050 I2C device class, 6-axis MotionApps 2.0 implementation
+// Based on InvenSense MPU-6050 register map document rev. 2.0, 5/19/2011 (RM-MPU-6000A-00)
+// 5/20/2013 by Jeff Rowberg
+// Updates should (hopefully) always be available at https://github.com/jrowberg/i2cdevlib
+//
+// Changelog:
+// 2019/07/08 - merged all DMP Firmware configuration items into the dmpMemory array
+// - Simplified dmpInitialize() to accomidate the dmpmemory array alterations
+// ... - ongoing debug release
+
+/* ============================================
+I2Cdev device library code is placed under the MIT license
+Copyright (c) 2012 Jeff Rowberg
+
+Permission is hereby granted, free of charge, to any person obtaining a copy
+of this software and associated documentation files (the "Software"), to deal
+in the Software without restriction, including without limitation the rights
+to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+copies of the Software, and to permit persons to whom the Software is
+furnished to do so, subject to the following conditions:
+
+The above copyright notice and this permission notice shall be included in
+all copies or substantial portions of the Software.
+
+THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+THE SOFTWARE.
+===============================================
+*/
+
+#ifndef _MPU6050_6AXIS_MOTIONAPPS20_H_
+#define _MPU6050_6AXIS_MOTIONAPPS20_H_
+
+#include "I2Cdev.h"
+#include "helper_3dmath.h"
+
+// MotionApps 2.0 DMP implementation, built using the MPU-6050EVB evaluation board
+#define MPU6050_INCLUDE_DMP_MOTIONAPPS20
+
+#include "MPU6050.h"
+
+// Tom Carpenter's conditional PROGMEM code
+// http://forum.arduino.cc/index.php?topic=129407.0
+#ifdef __AVR__
+ #include
+#elif defined(ESP8266) || defined(ESP32)
+ #include
+#else
+ // Teensy 3.0 library conditional PROGMEM code from Paul Stoffregen
+ #ifndef __PGMSPACE_H_
+ #define __PGMSPACE_H_ 1
+ #include
+
+ #define PROGMEM
+ #define PGM_P const char *
+ #define PSTR(str) (str)
+ #define F(x) x
+
+ typedef void prog_void;
+ typedef char prog_char;
+ typedef unsigned char prog_uchar;
+ typedef int8_t prog_int8_t;
+ typedef uint8_t prog_uint8_t;
+ typedef int16_t prog_int16_t;
+ typedef uint16_t prog_uint16_t;
+ typedef int32_t prog_int32_t;
+ typedef uint32_t prog_uint32_t;
+
+ #define strcpy_P(dest, src) strcpy((dest), (src))
+ #define strcat_P(dest, src) strcat((dest), (src))
+ #define strcmp_P(a, b) strcmp((a), (b))
+
+ #define pgm_read_byte(addr) (*(const unsigned char *)(addr))
+ #define pgm_read_word(addr) (*(const unsigned short *)(addr))
+ #define pgm_read_dword(addr) (*(const unsigned long *)(addr))
+ #define pgm_read_float(addr) (*(const float *)(addr))
+
+ #define pgm_read_byte_near(addr) pgm_read_byte(addr)
+ #define pgm_read_word_near(addr) pgm_read_word(addr)
+ #define pgm_read_dword_near(addr) pgm_read_dword(addr)
+ #define pgm_read_float_near(addr) pgm_read_float(addr)
+ #define pgm_read_byte_far(addr) pgm_read_byte(addr)
+ #define pgm_read_word_far(addr) pgm_read_word(addr)
+ #define pgm_read_dword_far(addr) pgm_read_dword(addr)
+ #define pgm_read_float_far(addr) pgm_read_float(addr)
+ #endif
+#endif
+
+/* Source is from the InvenSense MotionApps v2 demo code. Original source is
+ * unavailable, unless you happen to be amazing as decompiling binary by
+ * hand (in which case, please contact me, and I'm totally serious).
+ *
+ * Also, I'd like to offer many, many thanks to Noah Zerkin for all of the
+ * DMP reverse-engineering he did to help make this bit of wizardry
+ * possible.
+ */
+
+// NOTE! Enabling DEBUG adds about 3.3kB to the flash program size.
+// Debug output is now working even on ATMega328P MCUs (e.g. Arduino Uno)
+// after moving string constants to flash memory storage using the F()
+// compiler macro (Arduino IDE 1.0+ required).
+
+//#define DEBUG
+#ifdef DEBUG
+ #define DEBUG_PRINT(x) Serial.print(x)
+ #define DEBUG_PRINTF(x, y) Serial.print(x, y)
+ #define DEBUG_PRINTLN(x) Serial.println(x)
+ #define DEBUG_PRINTLNF(x, y) Serial.println(x, y)
+#else
+ #define DEBUG_PRINT(x)
+ #define DEBUG_PRINTF(x, y)
+ #define DEBUG_PRINTLN(x)
+ #define DEBUG_PRINTLNF(x, y)
+#endif
+
+#define MPU6050_DMP_CODE_SIZE 1929 // dmpMemory[]
+#define MPU6050_DMP_CONFIG_SIZE 192 // dmpConfig[]
+#define MPU6050_DMP_UPDATES_SIZE 47 // dmpUpdates[]
+
+/* ================================================================================================ *
+ | Default MotionApps v2.0 42-byte FIFO packet structure: |
+ | |
+ | [QUAT W][ ][QUAT X][ ][QUAT Y][ ][QUAT Z][ ][GYRO X][ ][GYRO Y][ ] |
+ | 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 |
+ | |
+ | [GYRO Z][ ][ACC X ][ ][ACC Y ][ ][ACC Z ][ ][ ] |
+ | 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 |
+ * ================================================================================================ */
+
+// this block of memory gets written to the MPU on start-up, and it seems
+// to be volatile memory, so it has to be done each time (it only takes ~1
+// second though)
+
+// I Only Changed this by applying all the configuration data and capturing it before startup:
+// *** this is a capture of the DMP Firmware after all the messy changes were made so we can just load it
+const unsigned char dmpMemory[MPU6050_DMP_CODE_SIZE] PROGMEM = {
+ /* bank # 0 */
+ 0xFB, 0x00, 0x00, 0x3E, 0x00, 0x0B, 0x00, 0x36, 0x00, 0x01, 0x00, 0x02, 0x00, 0x03, 0x00, 0x00,
+ 0x00, 0x65, 0x00, 0x54, 0xFF, 0xEF, 0x00, 0x00, 0xFA, 0x80, 0x00, 0x0B, 0x12, 0x82, 0x00, 0x01,
+ 0x00, 0x02, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+ 0x00, 0x28, 0x00, 0x00, 0xFF, 0xFF, 0x45, 0x81, 0xFF, 0xFF, 0xFA, 0x72, 0x00, 0x00, 0x00, 0x00,
+ 0x00, 0x00, 0x03, 0xE8, 0x00, 0x00, 0x00, 0x01, 0x00, 0x01, 0x7F, 0xFF, 0xFF, 0xFE, 0x80, 0x01,
+ 0x00, 0x1B, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+ 0x00, 0x40, 0x00, 0x00, 0x40, 0x00, 0x00, 0x00, 0x02, 0xCB, 0x47, 0xA2, 0x20, 0x00, 0x00, 0x00,
+ 0x20, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x40, 0x00, 0x00, 0x00, 0x60, 0x00, 0x00, 0x00,
+ 0x41, 0xFF, 0x00, 0x00, 0x00, 0x00, 0x0B, 0x2A, 0x00, 0x00, 0x16, 0x55, 0x00, 0x00, 0x21, 0x82,
+ 0xFD, 0x87, 0x26, 0x50, 0xFD, 0x80, 0x00, 0x00, 0x00, 0x1F, 0x00, 0x00, 0x00, 0x05, 0x80, 0x00,
+ 0x00, 0x00, 0x00, 0x00, 0x00, 0x01, 0x00, 0x00, 0x00, 0x02, 0x00, 0x00, 0x00, 0x03, 0x00, 0x00,
+ 0x40, 0x00, 0x00, 0x00, 0x00, 0x00, 0x04, 0x6F, 0x00, 0x02, 0x65, 0x32, 0x00, 0x00, 0x5E, 0xC0,
+ 0x40, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+ 0xFB, 0x8C, 0x6F, 0x5D, 0xFD, 0x5D, 0x08, 0xD9, 0x00, 0x7C, 0x73, 0x3B, 0x00, 0x6C, 0x12, 0xCC,
+ 0x32, 0x00, 0x13, 0x9D, 0x32, 0x00, 0xD0, 0xD6, 0x32, 0x00, 0x08, 0x00, 0x40, 0x00, 0x01, 0xF4,
+ 0xFF, 0xE6, 0x80, 0x79, 0x02, 0x00, 0x00, 0x00, 0x00, 0x00, 0xD0, 0xD6, 0x00, 0x00, 0x27, 0x10,
+ /* bank # 1 */
+ 0xFB, 0x00, 0x00, 0x00, 0x40, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+ 0x00, 0x00, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x01, 0x00, 0x01, 0x00, 0x00, 0x00,
+ 0x00, 0x00, 0xFA, 0x36, 0xFF, 0xBC, 0x30, 0x8E, 0x00, 0x05, 0xFB, 0xF0, 0xFF, 0xD9, 0x5B, 0xC8,
+ 0xFF, 0xD0, 0x9A, 0xBE, 0x00, 0x00, 0x10, 0xA9, 0xFF, 0xF4, 0x1E, 0xB2, 0x00, 0xCE, 0xBB, 0xF7,
+ 0x00, 0x00, 0x00, 0x01, 0x00, 0x00, 0x00, 0x04, 0x00, 0x02, 0x00, 0x02, 0x02, 0x00, 0x00, 0x0C,
+ 0xFF, 0xC2, 0x80, 0x00, 0x00, 0x01, 0x80, 0x00, 0x00, 0xCF, 0x80, 0x00, 0x40, 0x00, 0x00, 0x00,
+ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x06, 0x00, 0x00, 0x00, 0x00, 0x14,
+ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+ 0x09, 0x23, 0xA1, 0x35, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+ 0x00, 0x00, 0x00, 0x00, 0x03, 0x3F, 0x68, 0xB6, 0x79, 0x35, 0x28, 0xBC, 0xC6, 0x7E, 0xD1, 0x6C,
+ 0x80, 0x00, 0xFF, 0xFF, 0x40, 0x00, 0x00, 0x00, 0x00, 0x00, 0xB2, 0x6A, 0x00, 0x00, 0x00, 0x00,
+ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x3F, 0xF0, 0x00, 0x00, 0x00, 0x30,
+ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x40, 0x00,
+ 0x00, 0x00, 0x25, 0x4D, 0x00, 0x2F, 0x70, 0x6D, 0x00, 0x00, 0x05, 0xAE, 0x00, 0x0C, 0x02, 0xD0,
+ /* bank # 2 */
+ 0x00, 0x00, 0x00, 0x00, 0x00, 0x65, 0x00, 0x54, 0xFF, 0xEF, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+ 0x00, 0x00, 0x01, 0x00, 0x00, 0x44, 0x00, 0x01, 0x00, 0x05, 0x8B, 0xC1, 0x00, 0x00, 0x01, 0x00,
+ 0x00, 0x00, 0x00, 0x00, 0x00, 0x65, 0x00, 0x00, 0x00, 0x54, 0x00, 0x00, 0xFF, 0xEF, 0x00, 0x00,
+ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+ 0x00, 0x00, 0x00, 0x01, 0x00, 0x00, 0x00, 0x02, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+ 0x00, 0x1B, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+ 0x00, 0x1B, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+ /* bank # 3 */
+ 0xD8, 0xDC, 0xBA, 0xA2, 0xF1, 0xDE, 0xB2, 0xB8, 0xB4, 0xA8, 0x81, 0x91, 0xF7, 0x4A, 0x90, 0x7F,
+ 0x91, 0x6A, 0xF3, 0xF9, 0xDB, 0xA8, 0xF9, 0xB0, 0xBA, 0xA0, 0x80, 0xF2, 0xCE, 0x81, 0xF3, 0xC2,
+ 0xF1, 0xC1, 0xF2, 0xC3, 0xF3, 0xCC, 0xA2, 0xB2, 0x80, 0xF1, 0xC6, 0xD8, 0x80, 0xBA, 0xA7, 0xDF,
+ 0xDF, 0xDF, 0xF2, 0xA7, 0xC3, 0xCB, 0xC5, 0xB6, 0xF0, 0x87, 0xA2, 0x94, 0x24, 0x48, 0x70, 0x3C,
+ 0x95, 0x40, 0x68, 0x34, 0x58, 0x9B, 0x78, 0xA2, 0xF1, 0x83, 0x92, 0x2D, 0x55, 0x7D, 0xD8, 0xB1,
+ 0xB4, 0xB8, 0xA1, 0xD0, 0x91, 0x80, 0xF2, 0x70, 0xF3, 0x70, 0xF2, 0x7C, 0x80, 0xA8, 0xF1, 0x01,
+ 0xB0, 0x98, 0x87, 0xD9, 0x43, 0xD8, 0x86, 0xC9, 0x88, 0xBA, 0xA1, 0xF2, 0x0E, 0xB8, 0x97, 0x80,
+ 0xF1, 0xA9, 0xDF, 0xDF, 0xDF, 0xAA, 0xDF, 0xDF, 0xDF, 0xF2, 0xAA, 0x4C, 0xCD, 0x6C, 0xA9, 0x0C,
+ 0xC9, 0x2C, 0x97, 0x97, 0x97, 0x97, 0xF1, 0xA9, 0x89, 0x26, 0x46, 0x66, 0xB0, 0xB4, 0xBA, 0x80,
+ 0xAC, 0xDE, 0xF2, 0xCA, 0xF1, 0xB2, 0x8C, 0x02, 0xA9, 0xB6, 0x98, 0x00, 0x89, 0x0E, 0x16, 0x1E,
+ 0xB8, 0xA9, 0xB4, 0x99, 0x2C, 0x54, 0x7C, 0xB0, 0x8A, 0xA8, 0x96, 0x36, 0x56, 0x76, 0xF1, 0xB9,
+ 0xAF, 0xB4, 0xB0, 0x83, 0xC0, 0xB8, 0xA8, 0x97, 0x11, 0xB1, 0x8F, 0x98, 0xB9, 0xAF, 0xF0, 0x24,
+ 0x08, 0x44, 0x10, 0x64, 0x18, 0xF1, 0xA3, 0x29, 0x55, 0x7D, 0xAF, 0x83, 0xB5, 0x93, 0xAF, 0xF0,
+ 0x00, 0x28, 0x50, 0xF1, 0xA3, 0x86, 0x9F, 0x61, 0xA6, 0xDA, 0xDE, 0xDF, 0xD9, 0xFA, 0xA3, 0x86,
+ 0x96, 0xDB, 0x31, 0xA6, 0xD9, 0xF8, 0xDF, 0xBA, 0xA6, 0x8F, 0xC2, 0xC5, 0xC7, 0xB2, 0x8C, 0xC1,
+ 0xB8, 0xA2, 0xDF, 0xDF, 0xDF, 0xA3, 0xDF, 0xDF, 0xDF, 0xD8, 0xD8, 0xF1, 0xB8, 0xA8, 0xB2, 0x86,
+ /* bank # 4 */
+ 0xB4, 0x98, 0x0D, 0x35, 0x5D, 0xB8, 0xAA, 0x98, 0xB0, 0x87, 0x2D, 0x35, 0x3D, 0xB2, 0xB6, 0xBA,
+ 0xAF, 0x8C, 0x96, 0x19, 0x8F, 0x9F, 0xA7, 0x0E, 0x16, 0x1E, 0xB4, 0x9A, 0xB8, 0xAA, 0x87, 0x2C,
+ 0x54, 0x7C, 0xB9, 0xA3, 0xDE, 0xDF, 0xDF, 0xA3, 0xB1, 0x80, 0xF2, 0xC4, 0xCD, 0xC9, 0xF1, 0xB8,
+ 0xA9, 0xB4, 0x99, 0x83, 0x0D, 0x35, 0x5D, 0x89, 0xB9, 0xA3, 0x2D, 0x55, 0x7D, 0xB5, 0x93, 0xA3,
+ 0x0E, 0x16, 0x1E, 0xA9, 0x2C, 0x54, 0x7C, 0xB8, 0xB4, 0xB0, 0xF1, 0x97, 0x83, 0xA8, 0x11, 0x84,
+ 0xA5, 0x09, 0x98, 0xA3, 0x83, 0xF0, 0xDA, 0x24, 0x08, 0x44, 0x10, 0x64, 0x18, 0xD8, 0xF1, 0xA5,
+ 0x29, 0x55, 0x7D, 0xA5, 0x85, 0x95, 0x02, 0x1A, 0x2E, 0x3A, 0x56, 0x5A, 0x40, 0x48, 0xF9, 0xF3,
+ 0xA3, 0xD9, 0xF8, 0xF0, 0x98, 0x83, 0x24, 0x08, 0x44, 0x10, 0x64, 0x18, 0x97, 0x82, 0xA8, 0xF1,
+ 0x11, 0xF0, 0x98, 0xA2, 0x24, 0x08, 0x44, 0x10, 0x64, 0x18, 0xDA, 0xF3, 0xDE, 0xD8, 0x83, 0xA5,
+ 0x94, 0x01, 0xD9, 0xA3, 0x02, 0xF1, 0xA2, 0xC3, 0xC5, 0xC7, 0xD8, 0xF1, 0x84, 0x92, 0xA2, 0x4D,
+ 0xDA, 0x2A, 0xD8, 0x48, 0x69, 0xD9, 0x2A, 0xD8, 0x68, 0x55, 0xDA, 0x32, 0xD8, 0x50, 0x71, 0xD9,
+ 0x32, 0xD8, 0x70, 0x5D, 0xDA, 0x3A, 0xD8, 0x58, 0x79, 0xD9, 0x3A, 0xD8, 0x78, 0x93, 0xA3, 0x4D,
+ 0xDA, 0x2A, 0xD8, 0x48, 0x69, 0xD9, 0x2A, 0xD8, 0x68, 0x55, 0xDA, 0x32, 0xD8, 0x50, 0x71, 0xD9,
+ 0x32, 0xD8, 0x70, 0x5D, 0xDA, 0x3A, 0xD8, 0x58, 0x79, 0xD9, 0x3A, 0xD8, 0x78, 0xA8, 0x8A, 0x9A,
+ 0xF0, 0x28, 0x50, 0x78, 0x9E, 0xF3, 0x88, 0x18, 0xF1, 0x9F, 0x1D, 0x98, 0xA8, 0xD9, 0x08, 0xD8,
+ 0xC8, 0x9F, 0x12, 0x9E, 0xF3, 0x15, 0xA8, 0xDA, 0x12, 0x10, 0xD8, 0xF1, 0xAF, 0xC8, 0x97, 0x87,
+ /* bank # 5 */
+ 0x34, 0xB5, 0xB9, 0x94, 0xA4, 0x21, 0xF3, 0xD9, 0x22, 0xD8, 0xF2, 0x2D, 0xF3, 0xD9, 0x2A, 0xD8,
+ 0xF2, 0x35, 0xF3, 0xD9, 0x32, 0xD8, 0x81, 0xA4, 0x60, 0x60, 0x61, 0xD9, 0x61, 0xD8, 0x6C, 0x68,
+ 0x69, 0xD9, 0x69, 0xD8, 0x74, 0x70, 0x71, 0xD9, 0x71, 0xD8, 0xB1, 0xA3, 0x84, 0x19, 0x3D, 0x5D,
+ 0xA3, 0x83, 0x1A, 0x3E, 0x5E, 0x93, 0x10, 0x30, 0x81, 0x10, 0x11, 0xB8, 0xB0, 0xAF, 0x8F, 0x94,
+ 0xF2, 0xDA, 0x3E, 0xD8, 0xB4, 0x9A, 0xA8, 0x87, 0x29, 0xDA, 0xF8, 0xD8, 0x87, 0x9A, 0x35, 0xDA,
+ 0xF8, 0xD8, 0x87, 0x9A, 0x3D, 0xDA, 0xF8, 0xD8, 0xB1, 0xB9, 0xA4, 0x98, 0x85, 0x02, 0x2E, 0x56,
+ 0xA5, 0x81, 0x00, 0x0C, 0x14, 0xA3, 0x97, 0xB0, 0x8A, 0xF1, 0x2D, 0xD9, 0x28, 0xD8, 0x4D, 0xD9,
+ 0x48, 0xD8, 0x6D, 0xD9, 0x68, 0xD8, 0xB1, 0x84, 0x0D, 0xDA, 0x0E, 0xD8, 0xA3, 0x29, 0x83, 0xDA,
+ 0x2C, 0x0E, 0xD8, 0xA3, 0x84, 0x49, 0x83, 0xDA, 0x2C, 0x4C, 0x0E, 0xD8, 0xB8, 0xB0, 0xA8, 0x8A,
+ 0x9A, 0xF5, 0x20, 0xAA, 0xDA, 0xDF, 0xD8, 0xA8, 0x40, 0xAA, 0xD0, 0xDA, 0xDE, 0xD8, 0xA8, 0x60,
+ 0xAA, 0xDA, 0xD0, 0xDF, 0xD8, 0xF1, 0x97, 0x86, 0xA8, 0x31, 0x9B, 0x06, 0x99, 0x07, 0xAB, 0x97,
+ 0x28, 0x88, 0x9B, 0xF0, 0x0C, 0x20, 0x14, 0x40, 0xB8, 0xB0, 0xB4, 0xA8, 0x8C, 0x9C, 0xF0, 0x04,
+ 0x28, 0x51, 0x79, 0x1D, 0x30, 0x14, 0x38, 0xB2, 0x82, 0xAB, 0xD0, 0x98, 0x2C, 0x50, 0x50, 0x78,
+ 0x78, 0x9B, 0xF1, 0x1A, 0xB0, 0xF0, 0x8A, 0x9C, 0xA8, 0x29, 0x51, 0x79, 0x8B, 0x29, 0x51, 0x79,
+ 0x8A, 0x24, 0x70, 0x59, 0x8B, 0x20, 0x58, 0x71, 0x8A, 0x44, 0x69, 0x38, 0x8B, 0x39, 0x40, 0x68,
+ 0x8A, 0x64, 0x48, 0x31, 0x8B, 0x30, 0x49, 0x60, 0xA5, 0x88, 0x20, 0x09, 0x71, 0x58, 0x44, 0x68,
+ /* bank # 6 */
+ 0x11, 0x39, 0x64, 0x49, 0x30, 0x19, 0xF1, 0xAC, 0x00, 0x2C, 0x54, 0x7C, 0xF0, 0x8C, 0xA8, 0x04,
+ 0x28, 0x50, 0x78, 0xF1, 0x88, 0x97, 0x26, 0xA8, 0x59, 0x98, 0xAC, 0x8C, 0x02, 0x26, 0x46, 0x66,
+ 0xF0, 0x89, 0x9C, 0xA8, 0x29, 0x51, 0x79, 0x24, 0x70, 0x59, 0x44, 0x69, 0x38, 0x64, 0x48, 0x31,
+ 0xA9, 0x88, 0x09, 0x20, 0x59, 0x70, 0xAB, 0x11, 0x38, 0x40, 0x69, 0xA8, 0x19, 0x31, 0x48, 0x60,
+ 0x8C, 0xA8, 0x3C, 0x41, 0x5C, 0x20, 0x7C, 0x00, 0xF1, 0x87, 0x98, 0x19, 0x86, 0xA8, 0x6E, 0x76,
+ 0x7E, 0xA9, 0x99, 0x88, 0x2D, 0x55, 0x7D, 0x9E, 0xB9, 0xA3, 0x8A, 0x22, 0x8A, 0x6E, 0x8A, 0x56,
+ 0x8A, 0x5E, 0x9F, 0xB1, 0x83, 0x06, 0x26, 0x46, 0x66, 0x0E, 0x2E, 0x4E, 0x6E, 0x9D, 0xB8, 0xAD,
+ 0x00, 0x2C, 0x54, 0x7C, 0xF2, 0xB1, 0x8C, 0xB4, 0x99, 0xB9, 0xA3, 0x2D, 0x55, 0x7D, 0x81, 0x91,
+ 0xAC, 0x38, 0xAD, 0x3A, 0xB5, 0x83, 0x91, 0xAC, 0x2D, 0xD9, 0x28, 0xD8, 0x4D, 0xD9, 0x48, 0xD8,
+ 0x6D, 0xD9, 0x68, 0xD8, 0x8C, 0x9D, 0xAE, 0x29, 0xD9, 0x04, 0xAE, 0xD8, 0x51, 0xD9, 0x04, 0xAE,
+ 0xD8, 0x79, 0xD9, 0x04, 0xD8, 0x81, 0xF3, 0x9D, 0xAD, 0x00, 0x8D, 0xAE, 0x19, 0x81, 0xAD, 0xD9,
+ 0x01, 0xD8, 0xF2, 0xAE, 0xDA, 0x26, 0xD8, 0x8E, 0x91, 0x29, 0x83, 0xA7, 0xD9, 0xAD, 0xAD, 0xAD,
+ 0xAD, 0xF3, 0x2A, 0xD8, 0xD8, 0xF1, 0xB0, 0xAC, 0x89, 0x91, 0x3E, 0x5E, 0x76, 0xF3, 0xAC, 0x2E,
+ 0x2E, 0xF1, 0xB1, 0x8C, 0x5A, 0x9C, 0xAC, 0x2C, 0x28, 0x28, 0x28, 0x9C, 0xAC, 0x30, 0x18, 0xA8,
+ 0x98, 0x81, 0x28, 0x34, 0x3C, 0x97, 0x24, 0xA7, 0x28, 0x34, 0x3C, 0x9C, 0x24, 0xF2, 0xB0, 0x89,
+ 0xAC, 0x91, 0x2C, 0x4C, 0x6C, 0x8A, 0x9B, 0x2D, 0xD9, 0xD8, 0xD8, 0x51, 0xD9, 0xD8, 0xD8, 0x79,
+ /* bank # 7 */
+ 0xD9, 0xD8, 0xD8, 0xF1, 0x9E, 0x88, 0xA3, 0x31, 0xDA, 0xD8, 0xD8, 0x91, 0x2D, 0xD9, 0x28, 0xD8,
+ 0x4D, 0xD9, 0x48, 0xD8, 0x6D, 0xD9, 0x68, 0xD8, 0xB1, 0x83, 0x93, 0x35, 0x3D, 0x80, 0x25, 0xDA,
+ 0xD8, 0xD8, 0x85, 0x69, 0xDA, 0xD8, 0xD8, 0xB4, 0x93, 0x81, 0xA3, 0x28, 0x34, 0x3C, 0xF3, 0xAB,
+ 0x8B, 0xF8, 0xA3, 0x91, 0xB6, 0x09, 0xB4, 0xD9, 0xAB, 0xDE, 0xFA, 0xB0, 0x87, 0x9C, 0xB9, 0xA3,
+ 0xDD, 0xF1, 0x20, 0x28, 0x30, 0x38, 0x9A, 0xF1, 0x28, 0x30, 0x38, 0x9D, 0xF1, 0xA3, 0xA3, 0xA3,
+ 0xA3, 0xF2, 0xA3, 0xB4, 0x90, 0x80, 0xF2, 0xA3, 0xA3, 0xA3, 0xA3, 0xA3, 0xA3, 0xA3, 0xA3, 0xA3,
+ 0xA3, 0xB2, 0xA3, 0xA3, 0xA3, 0xA3, 0xA3, 0xA3, 0xB0, 0x87, 0xB5, 0x99, 0xF1, 0x28, 0x30, 0x38,
+ 0x98, 0xF1, 0xA3, 0xA3, 0xA3, 0xA3, 0x97, 0xA3, 0xA3, 0xA3, 0xA3, 0xF3, 0x9B, 0xA3, 0x30, 0xDC,
+ 0xB9, 0xA7, 0xF1, 0x26, 0x26, 0x26, 0xFE, 0xD8, 0xFF,
+
+};
+
+#ifndef MPU6050_DMP_FIFO_RATE_DIVISOR
+#define MPU6050_DMP_FIFO_RATE_DIVISOR 0x01 // The New instance of the Firmware has this as the default
+#endif
+
+// I Simplified this:
+uint8_t MPU6050::dmpInitialize() {
+ // reset device
+ DEBUG_PRINTLN(F("\n\nResetting MPU6050..."));
+ reset();
+ delay(30); // wait after reset
+
+ // enable sleep mode and wake cycle
+ /*Serial.println(F("Enabling sleep mode..."));
+ setSleepEnabled(true);
+ Serial.println(F("Enabling wake cycle..."));
+ setWakeCycleEnabled(true);*/
+
+ // disable sleep mode
+ setSleepEnabled(false);
+
+ // get MPU hardware revision
+ setMemoryBank(0x10, true, true);
+ setMemoryStartAddress(0x06);
+ Serial.println(F("Checking hardware revision..."));
+ Serial.print(F("Revision @ user[16][6] = "));
+ Serial.println(readMemoryByte(), HEX);
+ Serial.println(F("Resetting memory bank selection to 0..."));
+ setMemoryBank(0, false, false);
+
+ // check OTP bank valid
+ DEBUG_PRINTLN(F("Reading OTP bank valid flag..."));
+ DEBUG_PRINT(F("OTP bank is "));
+ DEBUG_PRINTLN(getOTPBankValid() ? F("valid!") : F("invalid!"));
+
+ // setup weird slave stuff (?)
+ DEBUG_PRINTLN(F("Setting slave 0 address to 0x7F..."));
+ setSlaveAddress(0, 0x7F);
+ DEBUG_PRINTLN(F("Disabling I2C Master mode..."));
+ setI2CMasterModeEnabled(false);
+ DEBUG_PRINTLN(F("Setting slave 0 address to 0x68 (self)..."));
+ setSlaveAddress(0, 0x68);
+ DEBUG_PRINTLN(F("Resetting I2C Master control..."));
+ resetI2CMaster();
+ delay(20);
+ DEBUG_PRINTLN(F("Setting clock source to Z Gyro..."));
+ setClockSource(MPU6050_CLOCK_PLL_ZGYRO);
+
+ DEBUG_PRINTLN(F("Setting DMP and FIFO_OFLOW interrupts enabled..."));
+ setIntEnabled(1<= dmpGetFIFOPacketSize();
+}
+
+// uint8_t MPU6050::dmpSetFIFORate(uint8_t fifoRate);
+// uint8_t MPU6050::dmpGetFIFORate();
+// uint8_t MPU6050::dmpGetSampleStepSizeMS();
+// uint8_t MPU6050::dmpGetSampleFrequency();
+// int32_t MPU6050::dmpDecodeTemperature(int8_t tempReg);
+
+//uint8_t MPU6050::dmpRegisterFIFORateProcess(inv_obj_func func, int16_t priority);
+//uint8_t MPU6050::dmpUnregisterFIFORateProcess(inv_obj_func func);
+//uint8_t MPU6050::dmpRunFIFORateProcesses();
+
+// uint8_t MPU6050::dmpSendQuaternion(uint_fast16_t accuracy);
+// uint8_t MPU6050::dmpSendGyro(uint_fast16_t elements, uint_fast16_t accuracy);
+// uint8_t MPU6050::dmpSendAccel(uint_fast16_t elements, uint_fast16_t accuracy);
+// uint8_t MPU6050::dmpSendLinearAccel(uint_fast16_t elements, uint_fast16_t accuracy);
+// uint8_t MPU6050::dmpSendLinearAccelInWorld(uint_fast16_t elements, uint_fast16_t accuracy);
+// uint8_t MPU6050::dmpSendControlData(uint_fast16_t elements, uint_fast16_t accuracy);
+// uint8_t MPU6050::dmpSendSensorData(uint_fast16_t elements, uint_fast16_t accuracy);
+// uint8_t MPU6050::dmpSendExternalSensorData(uint_fast16_t elements, uint_fast16_t accuracy);
+// uint8_t MPU6050::dmpSendGravity(uint_fast16_t elements, uint_fast16_t accuracy);
+// uint8_t MPU6050::dmpSendPacketNumber(uint_fast16_t accuracy);
+// uint8_t MPU6050::dmpSendQuantizedAccel(uint_fast16_t elements, uint_fast16_t accuracy);
+// uint8_t MPU6050::dmpSendEIS(uint_fast16_t elements, uint_fast16_t accuracy);
+
+uint8_t MPU6050::dmpGetAccel(int32_t *data, const uint8_t* packet) {
+ // TODO: accommodate different arrangements of sent data (ONLY default supported now)
+ if (packet == 0) packet = dmpPacketBuffer;
+ data[0] = (((uint32_t)packet[28] << 24) | ((uint32_t)packet[29] << 16) | ((uint32_t)packet[30] << 8) | packet[31]);
+ data[1] = (((uint32_t)packet[32] << 24) | ((uint32_t)packet[33] << 16) | ((uint32_t)packet[34] << 8) | packet[35]);
+ data[2] = (((uint32_t)packet[36] << 24) | ((uint32_t)packet[37] << 16) | ((uint32_t)packet[38] << 8) | packet[39]);
+ return 0;
+}
+uint8_t MPU6050::dmpGetAccel(int16_t *data, const uint8_t* packet) {
+ // TODO: accommodate different arrangements of sent data (ONLY default supported now)
+ if (packet == 0) packet = dmpPacketBuffer;
+ data[0] = (packet[28] << 8) | packet[29];
+ data[1] = (packet[32] << 8) | packet[33];
+ data[2] = (packet[36] << 8) | packet[37];
+ return 0;
+}
+uint8_t MPU6050::dmpGetAccel(VectorInt16 *v, const uint8_t* packet) {
+ // TODO: accommodate different arrangements of sent data (ONLY default supported now)
+ if (packet == 0) packet = dmpPacketBuffer;
+ v -> x = (packet[28] << 8) | packet[29];
+ v -> y = (packet[32] << 8) | packet[33];
+ v -> z = (packet[36] << 8) | packet[37];
+ return 0;
+}
+uint8_t MPU6050::dmpGetQuaternion(int32_t *data, const uint8_t* packet) {
+ // TODO: accommodate different arrangements of sent data (ONLY default supported now)
+ if (packet == 0) packet = dmpPacketBuffer;
+ data[0] = (((uint32_t)packet[0] << 24) | ((uint32_t)packet[1] << 16) | ((uint32_t)packet[2] << 8) | packet[3]);
+ data[1] = (((uint32_t)packet[4] << 24) | ((uint32_t)packet[5] << 16) | ((uint32_t)packet[6] << 8) | packet[7]);
+ data[2] = (((uint32_t)packet[8] << 24) | ((uint32_t)packet[9] << 16) | ((uint32_t)packet[10] << 8) | packet[11]);
+ data[3] = (((uint32_t)packet[12] << 24) | ((uint32_t)packet[13] << 16) | ((uint32_t)packet[14] << 8) | packet[15]);
+ return 0;
+}
+uint8_t MPU6050::dmpGetQuaternion(int16_t *data, const uint8_t* packet) {
+ // TODO: accommodate different arrangements of sent data (ONLY default supported now)
+ if (packet == 0) packet = dmpPacketBuffer;
+ data[0] = ((packet[0] << 8) | packet[1]);
+ data[1] = ((packet[4] << 8) | packet[5]);
+ data[2] = ((packet[8] << 8) | packet[9]);
+ data[3] = ((packet[12] << 8) | packet[13]);
+ return 0;
+}
+uint8_t MPU6050::dmpGetQuaternion(Quaternion *q, const uint8_t* packet) {
+ // TODO: accommodate different arrangements of sent data (ONLY default supported now)
+ int16_t qI[4];
+ uint8_t status = dmpGetQuaternion(qI, packet);
+ if (status == 0) {
+ q -> w = (float)qI[0] / 16384.0f;
+ q -> x = (float)qI[1] / 16384.0f;
+ q -> y = (float)qI[2] / 16384.0f;
+ q -> z = (float)qI[3] / 16384.0f;
+ return 0;
+ }
+ return status; // int16 return value, indicates error if this line is reached
+}
+// uint8_t MPU6050::dmpGet6AxisQuaternion(long *data, const uint8_t* packet);
+// uint8_t MPU6050::dmpGetRelativeQuaternion(long *data, const uint8_t* packet);
+uint8_t MPU6050::dmpGetGyro(int32_t *data, const uint8_t* packet) {
+ // TODO: accommodate different arrangements of sent data (ONLY default supported now)
+ if (packet == 0) packet = dmpPacketBuffer;
+ data[0] = (((uint32_t)packet[16] << 24) | ((uint32_t)packet[17] << 16) | ((uint32_t)packet[18] << 8) | packet[19]);
+ data[1] = (((uint32_t)packet[20] << 24) | ((uint32_t)packet[21] << 16) | ((uint32_t)packet[22] << 8) | packet[23]);
+ data[2] = (((uint32_t)packet[24] << 24) | ((uint32_t)packet[25] << 16) | ((uint32_t)packet[26] << 8) | packet[27]);
+ return 0;
+}
+uint8_t MPU6050::dmpGetGyro(int16_t *data, const uint8_t* packet) {
+ // TODO: accommodate different arrangements of sent data (ONLY default supported now)
+ if (packet == 0) packet = dmpPacketBuffer;
+ data[0] = (packet[16] << 8) | packet[17];
+ data[1] = (packet[20] << 8) | packet[21];
+ data[2] = (packet[24] << 8) | packet[25];
+ return 0;
+}
+uint8_t MPU6050::dmpGetGyro(VectorInt16 *v, const uint8_t* packet) {
+ // TODO: accommodate different arrangements of sent data (ONLY default supported now)
+ if (packet == 0) packet = dmpPacketBuffer;
+ v -> x = (packet[16] << 8) | packet[17];
+ v -> y = (packet[20] << 8) | packet[21];
+ v -> z = (packet[24] << 8) | packet[25];
+ return 0;
+}
+// uint8_t MPU6050::dmpSetLinearAccelFilterCoefficient(float coef);
+// uint8_t MPU6050::dmpGetLinearAccel(long *data, const uint8_t* packet);
+uint8_t MPU6050::dmpGetLinearAccel(VectorInt16 *v, VectorInt16 *vRaw, VectorFloat *gravity) {
+ // get rid of the gravity component (+1g = +8192 in standard DMP FIFO packet, sensitivity is 2g)
+ v -> x = vRaw -> x - gravity -> x*8192;
+ v -> y = vRaw -> y - gravity -> y*8192;
+ v -> z = vRaw -> z - gravity -> z*8192;
+ return 0;
+}
+// uint8_t MPU6050::dmpGetLinearAccelInWorld(long *data, const uint8_t* packet);
+uint8_t MPU6050::dmpGetLinearAccelInWorld(VectorInt16 *v, VectorInt16 *vReal, Quaternion *q) {
+ // rotate measured 3D acceleration vector into original state
+ // frame of reference based on orientation quaternion
+ memcpy(v, vReal, sizeof(VectorInt16));
+ v -> rotate(q);
+ return 0;
+}
+// uint8_t MPU6050::dmpGetGyroAndAccelSensor(long *data, const uint8_t* packet);
+// uint8_t MPU6050::dmpGetGyroSensor(long *data, const uint8_t* packet);
+// uint8_t MPU6050::dmpGetControlData(long *data, const uint8_t* packet);
+// uint8_t MPU6050::dmpGetTemperature(long *data, const uint8_t* packet);
+// uint8_t MPU6050::dmpGetGravity(long *data, const uint8_t* packet);
+uint8_t MPU6050::dmpGetGravity(int16_t *data, const uint8_t* packet) {
+ /* +1g corresponds to +8192, sensitivity is 2g. */
+ int16_t qI[4];
+ uint8_t status = dmpGetQuaternion(qI, packet);
+ data[0] = ((int32_t)qI[1] * qI[3] - (int32_t)qI[0] * qI[2]) / 16384;
+ data[1] = ((int32_t)qI[0] * qI[1] + (int32_t)qI[2] * qI[3]) / 16384;
+ data[2] = ((int32_t)qI[0] * qI[0] - (int32_t)qI[1] * qI[1]
+ - (int32_t)qI[2] * qI[2] + (int32_t)qI[3] * qI[3]) / (2 * 16384);
+ return status;
+}
+
+uint8_t MPU6050::dmpGetGravity(VectorFloat *v, Quaternion *q) {
+ v -> x = 2 * (q -> x*q -> z - q -> w*q -> y);
+ v -> y = 2 * (q -> w*q -> x + q -> y*q -> z);
+ v -> z = q -> w*q -> w - q -> x*q -> x - q -> y*q -> y + q -> z*q -> z;
+ return 0;
+}
+// uint8_t MPU6050::dmpGetUnquantizedAccel(long *data, const uint8_t* packet);
+// uint8_t MPU6050::dmpGetQuantizedAccel(long *data, const uint8_t* packet);
+// uint8_t MPU6050::dmpGetExternalSensorData(long *data, int size, const uint8_t* packet);
+// uint8_t MPU6050::dmpGetEIS(long *data, const uint8_t* packet);
+
+uint8_t MPU6050::dmpGetEuler(float *data, Quaternion *q) {
+ data[0] = atan2(2*q -> x*q -> y - 2*q -> w*q -> z, 2*q -> w*q -> w + 2*q -> x*q -> x - 1); // psi
+ data[1] = -asin(2*q -> x*q -> z + 2*q -> w*q -> y); // theta
+ data[2] = atan2(2*q -> y*q -> z - 2*q -> w*q -> x, 2*q -> w*q -> w + 2*q -> z*q -> z - 1); // phi
+ return 0;
+}
+
+#ifdef USE_OLD_DMPGETYAWPITCHROLL
+uint8_t MPU6050::dmpGetYawPitchRoll(float *data, Quaternion *q, VectorFloat *gravity) {
+ // yaw: (about Z axis)
+ data[0] = atan2(2*q -> x*q -> y - 2*q -> w*q -> z, 2*q -> w*q -> w + 2*q -> x*q -> x - 1);
+ // pitch: (nose up/down, about Y axis)
+ data[1] = atan(gravity -> x / sqrt(gravity -> y*gravity -> y + gravity -> z*gravity -> z));
+ // roll: (tilt left/right, about X axis)
+ data[2] = atan(gravity -> y / sqrt(gravity -> x*gravity -> x + gravity -> z*gravity -> z));
+ return 0;
+}
+#else
+uint8_t MPU6050::dmpGetYawPitchRoll(float *data, Quaternion *q, VectorFloat *gravity) {
+ // yaw: (about Z axis)
+ data[0] = atan2(2*q -> x*q -> y - 2*q -> w*q -> z, 2*q -> w*q -> w + 2*q -> x*q -> x - 1);
+ // pitch: (nose up/down, about Y axis)
+ data[1] = atan2(gravity -> x , sqrt(gravity -> y*gravity -> y + gravity -> z*gravity -> z));
+ // roll: (tilt left/right, about X axis)
+ data[2] = atan2(gravity -> y , gravity -> z);
+ if (gravity -> z < 0) {
+ if(data[1] > 0) {
+ data[1] = PI - data[1];
+ } else {
+ data[1] = -PI - data[1];
+ }
+ }
+ return 0;
+}
+#endif
+
+// uint8_t MPU6050::dmpGetAccelFloat(float *data, const uint8_t* packet);
+// uint8_t MPU6050::dmpGetQuaternionFloat(float *data, const uint8_t* packet);
+
+uint8_t MPU6050::dmpProcessFIFOPacket(const unsigned char *dmpData) {
+ /*for (uint8_t k = 0; k < dmpPacketSize; k++) {
+ if (dmpData[k] < 0x10) Serial.print("0");
+ Serial.print(dmpData[k], HEX);
+ Serial.print(" ");
+ }
+ Serial.print("\n");*/
+ //Serial.println((uint16_t)dmpPacketBuffer);
+ return 0;
+}
+uint8_t MPU6050::dmpReadAndProcessFIFOPacket(uint8_t numPackets, uint8_t *processed) {
+ uint8_t status;
+ uint8_t buf[dmpPacketSize];
+ for (uint8_t i = 0; i < numPackets; i++) {
+ // read packet from FIFO
+ getFIFOBytes(buf, dmpPacketSize);
+
+ // process packet
+ if ((status = dmpProcessFIFOPacket(buf)) > 0) return status;
+
+ // increment external process count variable, if supplied
+ if (processed != 0) (*processed)++;
+ }
+ return 0;
+}
+
+// uint8_t MPU6050::dmpSetFIFOProcessedCallback(void (*func) (void));
+
+// uint8_t MPU6050::dmpInitFIFOParam();
+// uint8_t MPU6050::dmpCloseFIFO();
+// uint8_t MPU6050::dmpSetGyroDataSource(uint_fast8_t source);
+// uint8_t MPU6050::dmpDecodeQuantizedAccel();
+// uint32_t MPU6050::dmpGetGyroSumOfSquare();
+// uint32_t MPU6050::dmpGetAccelSumOfSquare();
+// void MPU6050::dmpOverrideQuaternion(long *q);
+uint16_t MPU6050::dmpGetFIFOPacketSize() {
+ return dmpPacketSize;
+}
+
+#endif /* _MPU6050_6AXIS_MOTIONAPPS20_H_ */
diff --git a/Versions/dRehmFlight_ESP32_BETA_1.3/src/MPU6050/MPU6050_6Axis_MotionApps_V6_12.h b/Versions/dRehmFlight_ESP32_BETA_1.3/src/MPU6050/MPU6050_6Axis_MotionApps_V6_12.h
new file mode 100644
index 00000000..34a4ccc5
--- /dev/null
+++ b/Versions/dRehmFlight_ESP32_BETA_1.3/src/MPU6050/MPU6050_6Axis_MotionApps_V6_12.h
@@ -0,0 +1,617 @@
+// I2Cdev library collection - MPU6050 I2C device class, 6-axis MotionApps 6.12 implementation
+// Based on InvenSense MPU-6050 register map document rev. 2.0, 5/19/2011 (RM-MPU-6000A-00)
+// 5/20/2013 by Jeff Rowberg
+// Updates should (hopefully) always be available at https://github.com/jrowberg/i2cdevlib
+//
+// Changelog:
+// 2019/7/10 - I incorporated DMP Firmware Version 6.12 Latest as of today with many features and bug fixes.
+// - MPU6050 Registers have not changed just the DMP Image so that full backwards compatibility is present
+// - Run-time calibration routine is enabled which calibrates after no motion state is detected
+// - once no motion state is detected Calibration completes within 0.5 seconds
+// - The Drawback is that the firmware image is larger.
+// ... - ongoing debug release
+
+/* ============================================
+I2Cdev device library code is placed under the MIT license
+Copyright (c) 2012 Jeff Rowberg
+
+Permission is hereby granted, free of charge, to any person obtaining a copy
+of this software and associated documentation files (the "Software"), to deal
+in the Software without restriction, including without limitation the rights
+to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+copies of the Software, and to permit persons to whom the Software is
+furnished to do so, subject to the following conditions:
+
+The above copyright notice and this permission notice shall be included in
+all copies or substantial portions of the Software.
+
+THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+THE SOFTWARE.
+===============================================
+*/
+
+#ifndef _MPU6050_6AXIS_MOTIONAPPS20_H_
+#define _MPU6050_6AXIS_MOTIONAPPS20_H_
+
+#include "I2Cdev.h"
+#include "helper_3dmath.h"
+
+// MotionApps 2.0 DMP implementation, built using the MPU-6050EVB evaluation board
+#define MPU6050_INCLUDE_DMP_MOTIONAPPS20 // same definitions Should work with V6.12
+
+#include "MPU6050.h"
+
+// Tom Carpenter's conditional PROGMEM code
+// http://forum.arduino.cc/index.php?topic=129407.0
+#ifdef __AVR__
+ #include
+#elif defined(ESP8266) || defined(ESP32)
+ #include
+#else
+ // Teensy 3.0 library conditional PROGMEM code from Paul Stoffregen
+ #ifndef __PGMSPACE_H_
+ #define __PGMSPACE_H_ 1
+ #include
+
+ #define PROGMEM
+ #define PGM_P const char *
+ #define PSTR(str) (str)
+ #define F(x) x
+
+ typedef void prog_void;
+ typedef char prog_char;
+ typedef unsigned char prog_uchar;
+ typedef int8_t prog_int8_t;
+ typedef uint8_t prog_uint8_t;
+ typedef int16_t prog_int16_t;
+ typedef uint16_t prog_uint16_t;
+ typedef int32_t prog_int32_t;
+ typedef uint32_t prog_uint32_t;
+
+ #define strcpy_P(dest, src) strcpy((dest), (src))
+ #define strcat_P(dest, src) strcat((dest), (src))
+ #define strcmp_P(a, b) strcmp((a), (b))
+
+ #define pgm_read_byte(addr) (*(const unsigned char *)(addr))
+ #define pgm_read_word(addr) (*(const unsigned short *)(addr))
+ #define pgm_read_dword(addr) (*(const unsigned long *)(addr))
+ #define pgm_read_float(addr) (*(const float *)(addr))
+
+ #define pgm_read_byte_near(addr) pgm_read_byte(addr)
+ #define pgm_read_word_near(addr) pgm_read_word(addr)
+ #define pgm_read_dword_near(addr) pgm_read_dword(addr)
+ #define pgm_read_float_near(addr) pgm_read_float(addr)
+ #define pgm_read_byte_far(addr) pgm_read_byte(addr)
+ #define pgm_read_word_far(addr) pgm_read_word(addr)
+ #define pgm_read_dword_far(addr) pgm_read_dword(addr)
+ #define pgm_read_float_far(addr) pgm_read_float(addr)
+ #endif
+#endif
+
+/* Source is from the InvenSense MotionApps v2 demo code. Original source is
+ * unavailable, unless you happen to be amazing as decompiling binary by
+ * hand (in which case, please contact me, and I'm totally serious).
+ *
+ * Also, I'd like to offer many, many thanks to Noah Zerkin for all of the
+ * DMP reverse-engineering he did to help make this bit of wizardry
+ * possible.
+ */
+
+// NOTE! Enabling DEBUG adds about 3.3kB to the flash program size.
+// Debug output is now working even on ATMega328P MCUs (e.g. Arduino Uno)
+// after moving string constants to flash memory storage using the F()
+// compiler macro (Arduino IDE 1.0+ required).
+
+//#define DEBUG
+#ifdef DEBUG
+ #define DEBUG_PRINT(x) Serial.print(x)
+ #define DEBUG_PRINTF(x, y) Serial.print(x, y)
+ #define DEBUG_PRINTLN(x) Serial.println(x)
+ #define DEBUG_PRINTLNF(x, y) Serial.println(x, y)
+#else
+ #define DEBUG_PRINT(x)
+ #define DEBUG_PRINTF(x, y)
+ #define DEBUG_PRINTLN(x)
+ #define DEBUG_PRINTLNF(x, y)
+#endif
+
+#define MPU6050_DMP_CODE_SIZE 3062 // dmpMemory[]
+
+/* ================================================================ *
+ | Default MotionApps v6.12 28-byte FIFO packet structure: |
+ | |
+ | [QUAT W][ ][QUAT X][ ][QUAT Y][ ][QUAT Z][ ] |
+ | 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 |
+ | |
+ | [GYRO X][GYRO Y][GYRO Z][ACC X ][ACC Y ][ACC Z ] |
+ | 16 17 18 19 20 21 22 23 24 25 26 27 |
+ * ================================================================ */
+
+// this block of memory gets written to the MPU on start-up, and it seems
+// to be volatile memory, so it has to be done each time (it only takes ~1
+// second though)
+
+// *** this is a capture of the DMP Firmware V6.1.2 after all the messy changes were made so we can just load it
+const unsigned char dmpMemory[MPU6050_DMP_CODE_SIZE] PROGMEM = {
+/* bank # 0 */
+0x00, 0xF8, 0xF6, 0x2A, 0x3F, 0x68, 0xF5, 0x7A, 0x00, 0x06, 0xFF, 0xFE, 0x00, 0x03, 0x00, 0x00,
+0x00, 0x65, 0x00, 0x54, 0xFF, 0xEF, 0x00, 0x00, 0xFA, 0x80, 0x00, 0x0B, 0x12, 0x82, 0x00, 0x01,
+0x03, 0x0C, 0x30, 0xC3, 0x0A, 0x74, 0x56, 0x2D, 0x0D, 0x62, 0xDB, 0xC7, 0x16, 0xF4, 0xBA, 0x02,
+0x38, 0x83, 0xF8, 0x83, 0x30, 0x00, 0xF8, 0x83, 0x25, 0x8E, 0xF8, 0x83, 0x30, 0x00, 0xF8, 0x83,
+0xFF, 0xFF, 0xFF, 0xFF, 0x0C, 0xBD, 0xD8, 0x11, 0x24, 0x00, 0x04, 0x00, 0x1A, 0x82, 0x79, 0xA1,
+0x00, 0x36, 0x00, 0x3C, 0x00, 0x00, 0x00, 0x00, 0x00, 0x10, 0x00, 0x00, 0x38, 0x83, 0x6F, 0xA2,
+0x00, 0x3E, 0x03, 0x30, 0x40, 0x00, 0x00, 0x00, 0x02, 0xCA, 0xE3, 0x09, 0x3E, 0x80, 0x00, 0x00,
+0x20, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x40, 0x00, 0x00, 0x00, 0x60, 0x00, 0x00, 0x00,
+0x1F, 0xA4, 0xE8, 0xE4, 0xFF, 0xF5, 0xDC, 0xB9, 0x00, 0x5B, 0x79, 0xCF, 0x1F, 0x3F, 0x78, 0x76,
+0x00, 0x86, 0x7C, 0x5A, 0x00, 0x86, 0x23, 0x47, 0xFA, 0xB9, 0x86, 0x31, 0x00, 0x74, 0x87, 0x8A,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x43, 0x05, 0xFF, 0xFF, 0xE9, 0xA8, 0x00, 0x00, 0x21, 0x82,
+0xFA, 0xB8, 0x4D, 0x46, 0xFF, 0xFA, 0xDF, 0x3D, 0xFF, 0xFF, 0xB2, 0xB3, 0x00, 0x00, 0x00, 0x00,
+0x3F, 0xFF, 0xBA, 0x98, 0x00, 0x5D, 0xAC, 0x08, 0x00, 0x0A, 0x63, 0x78, 0x00, 0x01, 0x46, 0x21,
+0xFF, 0xFF, 0x00, 0x00, 0x00, 0x00, 0x42, 0xB5, 0x00, 0x06, 0x00, 0x64, 0x00, 0x64, 0x00, 0x06,
+0x14, 0x06, 0x02, 0x9F, 0x0F, 0x47, 0x91, 0x32, 0xD9, 0x0E, 0x9F, 0xC9, 0x1D, 0xCF, 0x4C, 0x34,
+0x3B, 0xB6, 0x7A, 0xE8, 0x00, 0x64, 0x00, 0x06, 0x00, 0xC8, 0x00, 0x00, 0x00, 0x00, 0xFF, 0xFE,
+/* bank # 1 */
+0x10, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+0x00, 0x07, 0x00, 0x00, 0xFF, 0xF1, 0x00, 0x00, 0xFA, 0x46, 0x00, 0x00, 0xA2, 0xB8, 0x00, 0x00,
+0x10, 0x00, 0x00, 0x00, 0x04, 0xD6, 0x00, 0x00, 0x04, 0xCC, 0x00, 0x00, 0x04, 0xCC, 0x00, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+0x00, 0x06, 0x00, 0x02, 0x00, 0x05, 0x00, 0x07, 0x00, 0x00, 0x00, 0x00, 0x00, 0x64, 0x00, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x0C, 0x00, 0x05, 0x00, 0x64, 0x00, 0x20, 0x00, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x40, 0x00, 0x00, 0x00, 0x03, 0x00,
+0x00, 0x00, 0x00, 0x32, 0xF8, 0x98, 0x00, 0x00, 0xFF, 0x65, 0x00, 0x00, 0x83, 0x0F, 0x00, 0x00,
+0x00, 0x06, 0x00, 0x00, 0xFF, 0xF1, 0x00, 0x00, 0xFA, 0x46, 0x00, 0x00, 0xA2, 0xB8, 0x00, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+0x00, 0x00, 0x00, 0x32, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x10, 0x00,
+0x00, 0x00, 0x00, 0x01, 0x00, 0x00, 0x00, 0x0D, 0x00, 0x00, 0xB2, 0x6A, 0x00, 0x02, 0x00, 0x00,
+0x00, 0x01, 0xFB, 0x83, 0x00, 0x7C, 0x00, 0x00, 0xFB, 0x15, 0xFC, 0x00, 0x1F, 0xB4, 0xFF, 0x83,
+0x00, 0x00, 0x00, 0x01, 0x00, 0x65, 0x00, 0x07, 0x00, 0x64, 0x03, 0xE8, 0x00, 0x64, 0x00, 0x28,
+0x00, 0x00, 0xFF, 0xFD, 0x00, 0x00, 0x00, 0x00, 0x16, 0xA0, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+0x00, 0x00, 0x10, 0x00, 0x00, 0x2F, 0x00, 0x00, 0x00, 0x00, 0x01, 0xF4, 0x00, 0x00, 0x10, 0x00,
+/* bank # 2 */
+0x00, 0x28, 0x00, 0x00, 0xFF, 0xFF, 0x45, 0x81, 0xFF, 0xFF, 0xFA, 0x72, 0x00, 0x00, 0x00, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x44, 0x00, 0x01, 0x00, 0x05, 0xBA, 0xC6, 0x00, 0x47, 0x78, 0xA2,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x06, 0x00, 0x00, 0x00, 0x00, 0x14,
+0x00, 0x00, 0x23, 0xBB, 0x00, 0x2E, 0xA2, 0x5B, 0x00, 0x00, 0x05, 0x68, 0x00, 0x0B, 0xCF, 0x49,
+0x00, 0x04, 0xFF, 0xFD, 0x00, 0x02, 0x00, 0x00, 0x00, 0x00, 0x00, 0x02, 0x00, 0x00, 0x00, 0x00,
+0x00, 0x1B, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+0x00, 0x64, 0x00, 0x07, 0x00, 0x08, 0x00, 0x06, 0x00, 0x06, 0xFF, 0xFE, 0x00, 0x00, 0x00, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+0x00, 0x2E, 0xA2, 0x5B, 0x00, 0x00, 0x05, 0x68, 0x00, 0x0B, 0xCF, 0x49, 0x00, 0x00, 0x00, 0x00,
+0x00, 0xF8, 0xF6, 0x2A, 0x3F, 0x68, 0xF5, 0x7A, 0x00, 0x04, 0xFF, 0xFD, 0x00, 0x02, 0x00, 0x00,
+0x00, 0x1B, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x0E, 0x00, 0x0E,
+0xFF, 0xFF, 0xFF, 0xCF, 0x00, 0x04, 0x00, 0x00, 0x00, 0x00, 0x00, 0x32, 0xFF, 0xFF, 0xFF, 0x9C,
+0x00, 0x00, 0x43, 0x05, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x01, 0x00, 0x00, 0x00, 0x64,
+0xFF, 0xE5, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+/* bank # 3 */
+0x00, 0x00, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+0x00, 0x01, 0x80, 0x00, 0x00, 0x01, 0x80, 0x00, 0x00, 0x01, 0x80, 0x00, 0x00, 0x24, 0x26, 0xD3,
+0x00, 0x01, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00, 0x00, 0x06, 0x00, 0x10, 0x00, 0x96, 0x00, 0x3C,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x1F, 0x9E, 0x65, 0x5D,
+0x0C, 0x0A, 0x4E, 0x68, 0xCD, 0xCF, 0x77, 0x09, 0x50, 0x16, 0x67, 0x59, 0xC6, 0x19, 0xCE, 0x82,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x47, 0x71, 0x1C,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x17, 0xD7, 0x84, 0x00, 0x03, 0x00, 0x00, 0x00,
+0x00, 0x11, 0xDC, 0x47, 0x03, 0x00, 0x00, 0x00, 0xC7, 0x93, 0x8F, 0x9D, 0x1E, 0x1B, 0x1C, 0x19,
+0xFF, 0xFF, 0xFF, 0xFF, 0x00, 0x00, 0x00, 0x00, 0x0E, 0xDF, 0xA4, 0x38, 0x1F, 0x9E, 0x65, 0x5D,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x47, 0x71, 0x1C, 0x02, 0x03, 0x18, 0x85, 0x00, 0x00, 0x40, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x03, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+0x3F, 0xFF, 0xFF, 0xFD, 0xFF, 0xFF, 0xF4, 0xC9, 0xFF, 0xFF, 0xBC, 0xF0, 0x00, 0x01, 0x0C, 0x0F,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+0xF5, 0xB7, 0xBA, 0xB3, 0x67, 0x7D, 0xDF, 0x7E, 0x72, 0x90, 0x2E, 0x55, 0x4C, 0xF6, 0xE6, 0x88,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+/* bank # 4 */
+0xD8, 0xDC, 0xB4, 0xB8, 0xB0, 0xD8, 0xB9, 0xAB, 0xF3, 0xF8, 0xFA, 0xB3, 0xB7, 0xBB, 0x8E, 0x9E,
+0xAE, 0xF1, 0x32, 0xF5, 0x1B, 0xF1, 0xB4, 0xB8, 0xB0, 0x80, 0x97, 0xF1, 0xA9, 0xDF, 0xDF, 0xDF,
+0xAA, 0xDF, 0xDF, 0xDF, 0xF2, 0xAA, 0x4C, 0xCD, 0x6C, 0xA9, 0x0C, 0xC9, 0x2C, 0x97, 0xF1, 0xA9,
+0x89, 0x26, 0x46, 0x66, 0xB2, 0x89, 0x99, 0xA9, 0x2D, 0x55, 0x7D, 0xB0, 0xB0, 0x8A, 0xA8, 0x96,
+0x36, 0x56, 0x76, 0xF1, 0xBA, 0xA3, 0xB4, 0xB2, 0x80, 0xC0, 0xB8, 0xA8, 0x97, 0x11, 0xB2, 0x83,
+0x98, 0xBA, 0xA3, 0xF0, 0x24, 0x08, 0x44, 0x10, 0x64, 0x18, 0xB2, 0xB9, 0xB4, 0x98, 0x83, 0xF1,
+0xA3, 0x29, 0x55, 0x7D, 0xBA, 0xB5, 0xB1, 0xA3, 0x83, 0x93, 0xF0, 0x00, 0x28, 0x50, 0xF5, 0xB2,
+0xB6, 0xAA, 0x83, 0x93, 0x28, 0x54, 0x7C, 0xF1, 0xB9, 0xA3, 0x82, 0x93, 0x61, 0xBA, 0xA2, 0xDA,
+0xDE, 0xDF, 0xDB, 0x81, 0x9A, 0xB9, 0xAE, 0xF5, 0x60, 0x68, 0x70, 0xF1, 0xDA, 0xBA, 0xA2, 0xDF,
+0xD9, 0xBA, 0xA2, 0xFA, 0xB9, 0xA3, 0x82, 0x92, 0xDB, 0x31, 0xBA, 0xA2, 0xD9, 0xBA, 0xA2, 0xF8,
+0xDF, 0x85, 0xA4, 0xD0, 0xC1, 0xBB, 0xAD, 0x83, 0xC2, 0xC5, 0xC7, 0xB8, 0xA2, 0xDF, 0xDF, 0xDF,
+0xBA, 0xA0, 0xDF, 0xDF, 0xDF, 0xD8, 0xD8, 0xF1, 0xB8, 0xAA, 0xB3, 0x8D, 0xB4, 0x98, 0x0D, 0x35,
+0x5D, 0xB2, 0xB6, 0xBA, 0xAF, 0x8C, 0x96, 0x19, 0x8F, 0x9F, 0xA7, 0x0E, 0x16, 0x1E, 0xB4, 0x9A,
+0xB8, 0xAA, 0x87, 0x2C, 0x54, 0x7C, 0xBA, 0xA4, 0xB0, 0x8A, 0xB6, 0x91, 0x32, 0x56, 0x76, 0xB2,
+0x84, 0x94, 0xA4, 0xC8, 0x08, 0xCD, 0xD8, 0xB8, 0xB4, 0xB0, 0xF1, 0x99, 0x82, 0xA8, 0x2D, 0x55,
+0x7D, 0x98, 0xA8, 0x0E, 0x16, 0x1E, 0xA2, 0x2C, 0x54, 0x7C, 0x92, 0xA4, 0xF0, 0x2C, 0x50, 0x78,
+/* bank # 5 */
+0xF1, 0x84, 0xA8, 0x98, 0xC4, 0xCD, 0xFC, 0xD8, 0x0D, 0xDB, 0xA8, 0xFC, 0x2D, 0xF3, 0xD9, 0xBA,
+0xA6, 0xF8, 0xDA, 0xBA, 0xA6, 0xDE, 0xD8, 0xBA, 0xB2, 0xB6, 0x86, 0x96, 0xA6, 0xD0, 0xF3, 0xC8,
+0x41, 0xDA, 0xA6, 0xC8, 0xF8, 0xD8, 0xB0, 0xB4, 0xB8, 0x82, 0xA8, 0x92, 0xF5, 0x2C, 0x54, 0x88,
+0x98, 0xF1, 0x35, 0xD9, 0xF4, 0x18, 0xD8, 0xF1, 0xA2, 0xD0, 0xF8, 0xF9, 0xA8, 0x84, 0xD9, 0xC7,
+0xDF, 0xF8, 0xF8, 0x83, 0xC5, 0xDA, 0xDF, 0x69, 0xDF, 0x83, 0xC1, 0xD8, 0xF4, 0x01, 0x14, 0xF1,
+0xA8, 0x82, 0x4E, 0xA8, 0x84, 0xF3, 0x11, 0xD1, 0x82, 0xF5, 0xD9, 0x92, 0x28, 0x97, 0x88, 0xF1,
+0x09, 0xF4, 0x1C, 0x1C, 0xD8, 0x84, 0xA8, 0xF3, 0xC0, 0xF9, 0xD1, 0xD9, 0x97, 0x82, 0xF1, 0x29,
+0xF4, 0x0D, 0xD8, 0xF3, 0xF9, 0xF9, 0xD1, 0xD9, 0x82, 0xF4, 0xC2, 0x03, 0xD8, 0xDE, 0xDF, 0x1A,
+0xD8, 0xF1, 0xA2, 0xFA, 0xF9, 0xA8, 0x84, 0x98, 0xD9, 0xC7, 0xDF, 0xF8, 0xF8, 0xF8, 0x83, 0xC7,
+0xDA, 0xDF, 0x69, 0xDF, 0xF8, 0x83, 0xC3, 0xD8, 0xF4, 0x01, 0x14, 0xF1, 0x98, 0xA8, 0x82, 0x2E,
+0xA8, 0x84, 0xF3, 0x11, 0xD1, 0x82, 0xF5, 0xD9, 0x92, 0x50, 0x97, 0x88, 0xF1, 0x09, 0xF4, 0x1C,
+0xD8, 0x84, 0xA8, 0xF3, 0xC0, 0xF8, 0xF9, 0xD1, 0xD9, 0x97, 0x82, 0xF1, 0x49, 0xF4, 0x0D, 0xD8,
+0xF3, 0xF9, 0xF9, 0xD1, 0xD9, 0x82, 0xF4, 0xC4, 0x03, 0xD8, 0xDE, 0xDF, 0xD8, 0xF1, 0xAD, 0x88,
+0x98, 0xCC, 0xA8, 0x09, 0xF9, 0xD9, 0x82, 0x92, 0xA8, 0xF5, 0x7C, 0xF1, 0x88, 0x3A, 0xCF, 0x94,
+0x4A, 0x6E, 0x98, 0xDB, 0x69, 0x31, 0xDA, 0xAD, 0xF2, 0xDE, 0xF9, 0xD8, 0x87, 0x95, 0xA8, 0xF2,
+0x21, 0xD1, 0xDA, 0xA5, 0xF9, 0xF4, 0x17, 0xD9, 0xF1, 0xAE, 0x8E, 0xD0, 0xC0, 0xC3, 0xAE, 0x82,
+/* bank # 6 */
+0xC6, 0x84, 0xC3, 0xA8, 0x85, 0x95, 0xC8, 0xA5, 0x88, 0xF2, 0xC0, 0xF1, 0xF4, 0x01, 0x0E, 0xF1,
+0x8E, 0x9E, 0xA8, 0xC6, 0x3E, 0x56, 0xF5, 0x54, 0xF1, 0x88, 0x72, 0xF4, 0x01, 0x15, 0xF1, 0x98,
+0x45, 0x85, 0x6E, 0xF5, 0x8E, 0x9E, 0x04, 0x88, 0xF1, 0x42, 0x98, 0x5A, 0x8E, 0x9E, 0x06, 0x88,
+0x69, 0xF4, 0x01, 0x1C, 0xF1, 0x98, 0x1E, 0x11, 0x08, 0xD0, 0xF5, 0x04, 0xF1, 0x1E, 0x97, 0x02,
+0x02, 0x98, 0x36, 0x25, 0xDB, 0xF9, 0xD9, 0x85, 0xA5, 0xF3, 0xC1, 0xDA, 0x85, 0xA5, 0xF3, 0xDF,
+0xD8, 0x85, 0x95, 0xA8, 0xF3, 0x09, 0xDA, 0xA5, 0xFA, 0xD8, 0x82, 0x92, 0xA8, 0xF5, 0x78, 0xF1,
+0x88, 0x1A, 0x84, 0x9F, 0x26, 0x88, 0x98, 0x21, 0xDA, 0xF4, 0x1D, 0xF3, 0xD8, 0x87, 0x9F, 0x39,
+0xD1, 0xAF, 0xD9, 0xDF, 0xDF, 0xFB, 0xF9, 0xF4, 0x0C, 0xF3, 0xD8, 0xFA, 0xD0, 0xF8, 0xDA, 0xF9,
+0xF9, 0xD0, 0xDF, 0xD9, 0xF9, 0xD8, 0xF4, 0x0B, 0xD8, 0xF3, 0x87, 0x9F, 0x39, 0xD1, 0xAF, 0xD9,
+0xDF, 0xDF, 0xF4, 0x1D, 0xF3, 0xD8, 0xFA, 0xFC, 0xA8, 0x69, 0xF9, 0xF9, 0xAF, 0xD0, 0xDA, 0xDE,
+0xFA, 0xD9, 0xF8, 0x8F, 0x9F, 0xA8, 0xF1, 0xCC, 0xF3, 0x98, 0xDB, 0x45, 0xD9, 0xAF, 0xDF, 0xD0,
+0xF8, 0xD8, 0xF1, 0x8F, 0x9F, 0xA8, 0xCA, 0xF3, 0x88, 0x09, 0xDA, 0xAF, 0x8F, 0xCB, 0xF8, 0xD8,
+0xF2, 0xAD, 0x97, 0x8D, 0x0C, 0xD9, 0xA5, 0xDF, 0xF9, 0xBA, 0xA6, 0xF3, 0xFA, 0xF4, 0x12, 0xF2,
+0xD8, 0x95, 0x0D, 0xD1, 0xD9, 0xBA, 0xA6, 0xF3, 0xFA, 0xDA, 0xA5, 0xF2, 0xC1, 0xBA, 0xA6, 0xF3,
+0xDF, 0xD8, 0xF1, 0xBA, 0xB2, 0xB6, 0x86, 0x96, 0xA6, 0xD0, 0xCA, 0xF3, 0x49, 0xDA, 0xA6, 0xCB,
+0xF8, 0xD8, 0xB0, 0xB4, 0xB8, 0xD8, 0xAD, 0x84, 0xF2, 0xC0, 0xDF, 0xF1, 0x8F, 0xCB, 0xC3, 0xA8,
+/* bank # 7 */
+0xB2, 0xB6, 0x86, 0x96, 0xC8, 0xC1, 0xCB, 0xC3, 0xF3, 0xB0, 0xB4, 0x88, 0x98, 0xA8, 0x21, 0xDB,
+0x71, 0x8D, 0x9D, 0x71, 0x85, 0x95, 0x21, 0xD9, 0xAD, 0xF2, 0xFA, 0xD8, 0x85, 0x97, 0xA8, 0x28,
+0xD9, 0xF4, 0x08, 0xD8, 0xF2, 0x8D, 0x29, 0xDA, 0xF4, 0x05, 0xD9, 0xF2, 0x85, 0xA4, 0xC2, 0xF2,
+0xD8, 0xA8, 0x8D, 0x94, 0x01, 0xD1, 0xD9, 0xF4, 0x11, 0xF2, 0xD8, 0x87, 0x21, 0xD8, 0xF4, 0x0A,
+0xD8, 0xF2, 0x84, 0x98, 0xA8, 0xC8, 0x01, 0xD1, 0xD9, 0xF4, 0x11, 0xD8, 0xF3, 0xA4, 0xC8, 0xBB,
+0xAF, 0xD0, 0xF2, 0xDE, 0xF8, 0xF8, 0xF8, 0xF8, 0xF8, 0xF8, 0xF8, 0xF8, 0xD8, 0xF1, 0xB8, 0xF6,
+0xB5, 0xB9, 0xB0, 0x8A, 0x95, 0xA3, 0xDE, 0x3C, 0xA3, 0xD9, 0xF8, 0xD8, 0x5C, 0xA3, 0xD9, 0xF8,
+0xD8, 0x7C, 0xA3, 0xD9, 0xF8, 0xD8, 0xF8, 0xF9, 0xD1, 0xA5, 0xD9, 0xDF, 0xDA, 0xFA, 0xD8, 0xB1,
+0x85, 0x30, 0xF7, 0xD9, 0xDE, 0xD8, 0xF8, 0x30, 0xAD, 0xDA, 0xDE, 0xD8, 0xF2, 0xB4, 0x8C, 0x99,
+0xA3, 0x2D, 0x55, 0x7D, 0xA0, 0x83, 0xDF, 0xDF, 0xDF, 0xB5, 0x91, 0xA0, 0xF6, 0x29, 0xD9, 0xFB,
+0xD8, 0xA0, 0xFC, 0x29, 0xD9, 0xFA, 0xD8, 0xA0, 0xD0, 0x51, 0xD9, 0xF8, 0xD8, 0xFC, 0x51, 0xD9,
+0xF9, 0xD8, 0x79, 0xD9, 0xFB, 0xD8, 0xA0, 0xD0, 0xFC, 0x79, 0xD9, 0xFA, 0xD8, 0xA1, 0xF9, 0xF9,
+0xF9, 0xF9, 0xF9, 0xA0, 0xDA, 0xDF, 0xDF, 0xDF, 0xD8, 0xA1, 0xF8, 0xF8, 0xF8, 0xF8, 0xF8, 0xAC,
+0xDE, 0xF8, 0xAD, 0xDE, 0x83, 0x93, 0xAC, 0x2C, 0x54, 0x7C, 0xF1, 0xA8, 0xDF, 0xDF, 0xDF, 0xF6,
+0x9D, 0x2C, 0xDA, 0xA0, 0xDF, 0xD9, 0xFA, 0xDB, 0x2D, 0xF8, 0xD8, 0xA8, 0x50, 0xDA, 0xA0, 0xD0,
+0xDE, 0xD9, 0xD0, 0xF8, 0xF8, 0xF8, 0xDB, 0x55, 0xF8, 0xD8, 0xA8, 0x78, 0xDA, 0xA0, 0xD0, 0xDF,
+/* bank # 8 */
+0xD9, 0xD0, 0xFA, 0xF8, 0xF8, 0xF8, 0xF8, 0xDB, 0x7D, 0xF8, 0xD8, 0x9C, 0xA8, 0x8C, 0xF5, 0x30,
+0xDB, 0x38, 0xD9, 0xD0, 0xDE, 0xDF, 0xA0, 0xD0, 0xDE, 0xDF, 0xD8, 0xA8, 0x48, 0xDB, 0x58, 0xD9,
+0xDF, 0xD0, 0xDE, 0xA0, 0xDF, 0xD0, 0xDE, 0xD8, 0xA8, 0x68, 0xDB, 0x70, 0xD9, 0xDF, 0xDF, 0xA0,
+0xDF, 0xDF, 0xD8, 0xF1, 0xA8, 0x88, 0x90, 0x2C, 0x54, 0x7C, 0x98, 0xA8, 0xD0, 0x5C, 0x38, 0xD1,
+0xDA, 0xF2, 0xAE, 0x8C, 0xDF, 0xF9, 0xD8, 0xB0, 0x87, 0xA8, 0xC1, 0xC1, 0xB1, 0x88, 0xA8, 0xC6,
+0xF9, 0xF9, 0xDA, 0x36, 0xD8, 0xA8, 0xF9, 0xDA, 0x36, 0xD8, 0xA8, 0xF9, 0xDA, 0x36, 0xD8, 0xA8,
+0xF9, 0xDA, 0x36, 0xD8, 0xA8, 0xF9, 0xDA, 0x36, 0xD8, 0xF7, 0x8D, 0x9D, 0xAD, 0xF8, 0x18, 0xDA,
+0xF2, 0xAE, 0xDF, 0xD8, 0xF7, 0xAD, 0xFA, 0x30, 0xD9, 0xA4, 0xDE, 0xF9, 0xD8, 0xF2, 0xAE, 0xDE,
+0xFA, 0xF9, 0x83, 0xA7, 0xD9, 0xC3, 0xC5, 0xC7, 0xF1, 0x88, 0x9B, 0xA7, 0x7A, 0xAD, 0xF7, 0xDE,
+0xDF, 0xA4, 0xF8, 0x84, 0x94, 0x08, 0xA7, 0x97, 0xF3, 0x00, 0xAE, 0xF2, 0x98, 0x19, 0xA4, 0x88,
+0xC6, 0xA3, 0x94, 0x88, 0xF6, 0x32, 0xDF, 0xF2, 0x83, 0x93, 0xDB, 0x09, 0xD9, 0xF2, 0xAA, 0xDF,
+0xD8, 0xD8, 0xAE, 0xF8, 0xF9, 0xD1, 0xDA, 0xF3, 0xA4, 0xDE, 0xA7, 0xF1, 0x88, 0x9B, 0x7A, 0xD8,
+0xF3, 0x84, 0x94, 0xAE, 0x19, 0xF9, 0xDA, 0xAA, 0xF1, 0xDF, 0xD8, 0xA8, 0x81, 0xC0, 0xC3, 0xC5,
+0xC7, 0xA3, 0x92, 0x83, 0xF6, 0x28, 0xAD, 0xDE, 0xD9, 0xF8, 0xD8, 0xA3, 0x50, 0xAD, 0xD9, 0xF8,
+0xD8, 0xA3, 0x78, 0xAD, 0xD9, 0xF8, 0xD8, 0xF8, 0xF9, 0xD1, 0xA1, 0xDA, 0xDE, 0xC3, 0xC5, 0xC7,
+0xD8, 0xA1, 0x81, 0x94, 0xF8, 0x18, 0xF2, 0xB0, 0x89, 0xAC, 0xC3, 0xC5, 0xC7, 0xF1, 0xD8, 0xB8,
+/* bank # 9 */
+0xB4, 0xB0, 0x97, 0x86, 0xA8, 0x31, 0x9B, 0x06, 0x99, 0x07, 0xAB, 0x97, 0x28, 0x88, 0x9B, 0xF0,
+0x0C, 0x20, 0x14, 0x40, 0xB0, 0xB4, 0xB8, 0xF0, 0xA8, 0x8A, 0x9A, 0x28, 0x50, 0x78, 0xB7, 0x9B,
+0xA8, 0x29, 0x51, 0x79, 0x24, 0x70, 0x59, 0x44, 0x69, 0x38, 0x64, 0x48, 0x31, 0xF1, 0xBB, 0xAB,
+0x88, 0x00, 0x2C, 0x54, 0x7C, 0xF0, 0xB3, 0x8B, 0xB8, 0xA8, 0x04, 0x28, 0x50, 0x78, 0xF1, 0xB0,
+0x88, 0xB4, 0x97, 0x26, 0xA8, 0x59, 0x98, 0xBB, 0xAB, 0xB3, 0x8B, 0x02, 0x26, 0x46, 0x66, 0xB0,
+0xB8, 0xF0, 0x8A, 0x9C, 0xA8, 0x29, 0x51, 0x79, 0x8B, 0x29, 0x51, 0x79, 0x8A, 0x24, 0x70, 0x59,
+0x8B, 0x20, 0x58, 0x71, 0x8A, 0x44, 0x69, 0x38, 0x8B, 0x39, 0x40, 0x68, 0x8A, 0x64, 0x48, 0x31,
+0x8B, 0x30, 0x49, 0x60, 0x88, 0xF1, 0xAC, 0x00, 0x2C, 0x54, 0x7C, 0xF0, 0x8C, 0xA8, 0x04, 0x28,
+0x50, 0x78, 0xF1, 0x88, 0x97, 0x26, 0xA8, 0x59, 0x98, 0xAC, 0x8C, 0x02, 0x26, 0x46, 0x66, 0xF0,
+0x89, 0x9C, 0xA8, 0x29, 0x51, 0x79, 0x24, 0x70, 0x59, 0x44, 0x69, 0x38, 0x64, 0x48, 0x31, 0xA9,
+0x88, 0x09, 0x20, 0x59, 0x70, 0xAB, 0x11, 0x38, 0x40, 0x69, 0xA8, 0x19, 0x31, 0x48, 0x60, 0x8C,
+0xA8, 0x3C, 0x41, 0x5C, 0x20, 0x7C, 0x00, 0xF1, 0x87, 0x98, 0x19, 0x86, 0xA8, 0x6E, 0x76, 0x7E,
+0xA9, 0x99, 0x88, 0x2D, 0x55, 0x7D, 0xD8, 0xB1, 0xB5, 0xB9, 0xA3, 0xDF, 0xDF, 0xDF, 0xAE, 0xD0,
+0xDF, 0xAA, 0xD0, 0xDE, 0xF2, 0xAB, 0xF8, 0xF9, 0xD9, 0xB0, 0x87, 0xC4, 0xAA, 0xF1, 0xDF, 0xDF,
+0xBB, 0xAF, 0xDF, 0xDF, 0xB9, 0xD8, 0xB1, 0xF1, 0xA3, 0x97, 0x8E, 0x60, 0xDF, 0xB0, 0x84, 0xF2,
+0xC8, 0xF8, 0xF9, 0xD9, 0xDE, 0xD8, 0x93, 0x85, 0xF1, 0x4A, 0xB1, 0x83, 0xA3, 0x08, 0xB5, 0x83,
+/* bank # 10 */
+0x9A, 0x08, 0x10, 0xB7, 0x9F, 0x10, 0xD8, 0xF1, 0xB0, 0xBA, 0xAE, 0xB0, 0x8A, 0xC2, 0xB2, 0xB6,
+0x8E, 0x9E, 0xF1, 0xFB, 0xD9, 0xF4, 0x1D, 0xD8, 0xF9, 0xD9, 0x0C, 0xF1, 0xD8, 0xF8, 0xF8, 0xAD,
+0x61, 0xD9, 0xAE, 0xFB, 0xD8, 0xF4, 0x0C, 0xF1, 0xD8, 0xF8, 0xF8, 0xAD, 0x19, 0xD9, 0xAE, 0xFB,
+0xDF, 0xD8, 0xF4, 0x16, 0xF1, 0xD8, 0xF8, 0xAD, 0x8D, 0x61, 0xD9, 0xF4, 0xF4, 0xAC, 0xF5, 0x9C,
+0x9C, 0x8D, 0xDF, 0x2B, 0xBA, 0xB6, 0xAE, 0xFA, 0xF8, 0xF4, 0x0B, 0xD8, 0xF1, 0xAE, 0xD0, 0xF8,
+0xAD, 0x51, 0xDA, 0xAE, 0xFA, 0xF8, 0xF1, 0xD8, 0xB9, 0xB1, 0xB6, 0xA3, 0x83, 0x9C, 0x08, 0xB9,
+0xB1, 0x83, 0x9A, 0xB5, 0xAA, 0xC0, 0xFD, 0x30, 0x83, 0xB7, 0x9F, 0x10, 0xB5, 0x8B, 0x93, 0xF2,
+0x02, 0x02, 0xD1, 0xAB, 0xDA, 0xDE, 0xD8, 0xF1, 0xB0, 0x80, 0xBA, 0xAB, 0xC0, 0xC3, 0xB2, 0x84,
+0xC1, 0xC3, 0xD8, 0xB1, 0xB9, 0xF3, 0x8B, 0xA3, 0x91, 0xB6, 0x09, 0xB4, 0xD9, 0xAB, 0xDE, 0xB0,
+0x87, 0x9C, 0xB9, 0xA3, 0xDD, 0xF1, 0xB3, 0x8B, 0x8B, 0x8B, 0x8B, 0x8B, 0xB0, 0x87, 0x20, 0x28,
+0x30, 0x38, 0xB2, 0x8B, 0xB6, 0x9B, 0xF2, 0xA3, 0xC0, 0xC8, 0xC2, 0xC4, 0xCC, 0xC6, 0xA3, 0xA3,
+0xA3, 0xF1, 0xB0, 0x87, 0xB5, 0x9A, 0xD8, 0xF3, 0x9B, 0xA3, 0xA3, 0xDC, 0xBA, 0xAC, 0xDF, 0xB9,
+0xA3, 0xFE, 0xF2, 0xAB, 0xC4, 0xAA, 0xF1, 0xDF, 0xDF, 0xBB, 0xAF, 0xDF, 0xDF, 0xA3, 0xA3, 0xA3,
+0xD8, 0xD8, 0xD8, 0xBB, 0xB3, 0xB7, 0xF1, 0xAA, 0xF9, 0xDA, 0xFF, 0xD9, 0x80, 0x9A, 0xAA, 0x28,
+0xB4, 0x80, 0x98, 0xA7, 0x20, 0xB7, 0x97, 0x87, 0xA8, 0x66, 0x88, 0xF0, 0x79, 0x51, 0xF1, 0x90,
+0x2C, 0x87, 0x0C, 0xA7, 0x81, 0x97, 0x62, 0x93, 0xF0, 0x71, 0x71, 0x60, 0x85, 0x94, 0x01, 0x29,
+/* bank # 11 */
+0x51, 0x79, 0x90, 0xA5, 0xF1, 0x28, 0x4C, 0x6C, 0x87, 0x0C, 0x95, 0x18, 0x85, 0x78, 0xA3, 0x83,
+0x90, 0x28, 0x4C, 0x6C, 0x88, 0x6C, 0xD8, 0xF3, 0xA2, 0x82, 0x00, 0xF2, 0x10, 0xA8, 0x92, 0x19,
+0x80, 0xA2, 0xF2, 0xD9, 0x26, 0xD8, 0xF1, 0x88, 0xA8, 0x4D, 0xD9, 0x48, 0xD8, 0x96, 0xA8, 0x39,
+0x80, 0xD9, 0x3C, 0xD8, 0x95, 0x80, 0xA8, 0x39, 0xA6, 0x86, 0x98, 0xD9, 0x2C, 0xDA, 0x87, 0xA7,
+0x2C, 0xD8, 0xA8, 0x89, 0x95, 0x19, 0xA9, 0x80, 0xD9, 0x38, 0xD8, 0xA8, 0x89, 0x39, 0xA9, 0x80,
+0xDA, 0x3C, 0xD8, 0xA8, 0x2E, 0xA8, 0x39, 0x90, 0xD9, 0x0C, 0xD8, 0xA8, 0x95, 0x31, 0x98, 0xD9,
+0x0C, 0xD8, 0xA8, 0x09, 0xD9, 0xFF, 0xD8, 0x01, 0xDA, 0xFF, 0xD8, 0x95, 0x39, 0xA9, 0xDA, 0x26,
+0xFF, 0xD8, 0x90, 0xA8, 0x0D, 0x89, 0x99, 0xA8, 0x10, 0x80, 0x98, 0x21, 0xDA, 0x2E, 0xD8, 0x89,
+0x99, 0xA8, 0x31, 0x80, 0xDA, 0x2E, 0xD8, 0xA8, 0x86, 0x96, 0x31, 0x80, 0xDA, 0x2E, 0xD8, 0xA8,
+0x87, 0x31, 0x80, 0xDA, 0x2E, 0xD8, 0xA8, 0x82, 0x92, 0xF3, 0x41, 0x80, 0xF1, 0xD9, 0x2E, 0xD8,
+0xA8, 0x82, 0xF3, 0x19, 0x80, 0xF1, 0xD9, 0x2E, 0xD8, 0x82, 0xAC, 0xF3, 0xC0, 0xA2, 0x80, 0x22,
+0xF1, 0xA6, 0x2E, 0xA7, 0x2E, 0xA9, 0x22, 0x98, 0xA8, 0x29, 0xDA, 0xAC, 0xDE, 0xFF, 0xD8, 0xA2,
+0xF2, 0x2A, 0xF1, 0xA9, 0x2E, 0x82, 0x92, 0xA8, 0xF2, 0x31, 0x80, 0xA6, 0x96, 0xF1, 0xD9, 0x00,
+0xAC, 0x8C, 0x9C, 0x0C, 0x30, 0xAC, 0xDE, 0xD0, 0xDE, 0xFF, 0xD8, 0x8C, 0x9C, 0xAC, 0xD0, 0x10,
+0xAC, 0xDE, 0x80, 0x92, 0xA2, 0xF2, 0x4C, 0x82, 0xA8, 0xF1, 0xCA, 0xF2, 0x35, 0xF1, 0x96, 0x88,
+0xA6, 0xD9, 0x00, 0xD8, 0xF1, 0xFF,
+};
+
+// this divisor is pre configured into the above image and can't be modified at this time.
+#ifndef MPU6050_DMP_FIFO_RATE_DIVISOR
+#define MPU6050_DMP_FIFO_RATE_DIVISOR 0x01 // The New instance of the Firmware has this as the default
+#endif
+
+// this is the most basic initialization I can create. with the intent that we access the register bytes as few times as needed to get the job done.
+// for detailed descriptins of all registers and there purpose google "MPU-6000/MPU-6050 Register Map and Descriptions"
+uint8_t MPU6050::dmpInitialize() { // Lets get it over with fast Write everything once and set it up necely
+ uint8_t val;
+ uint16_t ival;
+ // Reset procedure per instructions in the "MPU-6000/MPU-6050 Register Map and Descriptions" page 41
+ I2Cdev::writeBit(devAddr,0x6B, 7, (val = 1)); //PWR_MGMT_1: reset with 100ms delay
+ delay(100);
+ I2Cdev::writeBits(devAddr,0x6A, 2, 3, (val = 0b111)); // full SIGNAL_PATH_RESET: with another 100ms delay
+ delay(100);
+ I2Cdev::writeBytes(devAddr,0x6B, 1, &(val = 0x01)); // 1000 0001 PWR_MGMT_1:Clock Source Select PLL_X_gyro
+ I2Cdev::writeBytes(devAddr,0x38, 1, &(val = 0x00)); // 0000 0000 INT_ENABLE: no Interrupt
+ I2Cdev::writeBytes(devAddr,0x23, 1, &(val = 0x00)); // 0000 0000 MPU FIFO_EN: (all off) Using DMP's FIFO instead
+ I2Cdev::writeBytes(devAddr,0x1C, 1, &(val = 0x00)); // 0000 0000 ACCEL_CONFIG: 0 = Accel Full Scale Select: 2g
+ I2Cdev::writeBytes(devAddr,0x37, 1, &(val = 0x80)); // 1001 0000 INT_PIN_CFG: ACTL The logic level for int pin is active low. and interrupt status bits are cleared on any read
+ I2Cdev::writeBytes(devAddr,0x6B, 1, &(val = 0x01)); // 0000 0001 PWR_MGMT_1: Clock Source Select PLL_X_gyro
+ I2Cdev::writeBytes(devAddr,0x19, 1, &(val = 0x04)); // 0000 0100 SMPLRT_DIV: Divides the internal sample rate 400Hz ( Sample Rate = Gyroscope Output Rate / (1 + SMPLRT_DIV))
+ I2Cdev::writeBytes(devAddr,0x1A, 1, &(val = 0x01)); // 0000 0001 CONFIG: Digital Low Pass Filter (DLPF) Configuration 188HZ //Im betting this will be the beat
+ if (!writeProgMemoryBlock(dmpMemory, MPU6050_DMP_CODE_SIZE)) return 1; // Loads the DMP image into the MPU6050 Memory // Should Never Fail
+ I2Cdev::writeWords(devAddr, 0x70, 1, &(ival = 0x0400)); // DMP Program Start Address
+ I2Cdev::writeBytes(devAddr,0x1B, 1, &(val = 0x18)); // 0001 1000 GYRO_CONFIG: 3 = +2000 Deg/sec
+ I2Cdev::writeBytes(devAddr,0x6A, 1, &(val = 0xC0)); // 1100 1100 USER_CTRL: Enable Fifo and Reset Fifo
+ I2Cdev::writeBytes(devAddr,0x38, 1, &(val = 0x02)); // 0000 0010 INT_ENABLE: RAW_DMP_INT_EN on
+ I2Cdev::writeBit(devAddr,0x6A, 2, 1); // Reset FIFO one last time just for kicks. (MPUi2cWrite reads 0x6A first and only alters 1 bit and then saves the byte)
+
+ setDMPEnabled(false); // disable DMP for compatibility with the MPU6050 library
+/*
+ dmpPacketSize += 16;//DMP_FEATURE_6X_LP_QUAT
+ dmpPacketSize += 6;//DMP_FEATURE_SEND_RAW_ACCEL
+ dmpPacketSize += 6;//DMP_FEATURE_SEND_RAW_GYRO
+*/
+ dmpPacketSize = 28;
+ return 0;
+}
+
+bool MPU6050::dmpPacketAvailable() {
+ return getFIFOCount() >= dmpGetFIFOPacketSize();
+}
+
+// uint8_t MPU6050::dmpSetFIFORate(uint8_t fifoRate);
+// uint8_t MPU6050::dmpGetFIFORate();
+// uint8_t MPU6050::dmpGetSampleStepSizeMS();
+// uint8_t MPU6050::dmpGetSampleFrequency();
+// int32_t MPU6050::dmpDecodeTemperature(int8_t tempReg);
+
+//uint8_t MPU6050::dmpRegisterFIFORateProcess(inv_obj_func func, int16_t priority);
+//uint8_t MPU6050::dmpUnregisterFIFORateProcess(inv_obj_func func);
+//uint8_t MPU6050::dmpRunFIFORateProcesses();
+
+// uint8_t MPU6050::dmpSendQuaternion(uint_fast16_t accuracy);
+// uint8_t MPU6050::dmpSendGyro(uint_fast16_t elements, uint_fast16_t accuracy);
+// uint8_t MPU6050::dmpSendAccel(uint_fast16_t elements, uint_fast16_t accuracy);
+// uint8_t MPU6050::dmpSendLinearAccel(uint_fast16_t elements, uint_fast16_t accuracy);
+// uint8_t MPU6050::dmpSendLinearAccelInWorld(uint_fast16_t elements, uint_fast16_t accuracy);
+// uint8_t MPU6050::dmpSendControlData(uint_fast16_t elements, uint_fast16_t accuracy);
+// uint8_t MPU6050::dmpSendSensorData(uint_fast16_t elements, uint_fast16_t accuracy);
+// uint8_t MPU6050::dmpSendExternalSensorData(uint_fast16_t elements, uint_fast16_t accuracy);
+// uint8_t MPU6050::dmpSendGravity(uint_fast16_t elements, uint_fast16_t accuracy);
+// uint8_t MPU6050::dmpSendPacketNumber(uint_fast16_t accuracy);
+// uint8_t MPU6050::dmpSendQuantizedAccel(uint_fast16_t elements, uint_fast16_t accuracy);
+// uint8_t MPU6050::dmpSendEIS(uint_fast16_t elements, uint_fast16_t accuracy);
+
+uint8_t MPU6050::dmpGetAccel(int32_t *data, const uint8_t* packet) {
+ // TODO: accommodate different arrangements of sent data (ONLY default supported now)
+ if (packet == 0) packet = dmpPacketBuffer;
+ data[0] = (((uint32_t)packet[16] << 8) | packet[17]);
+ data[1] = (((uint32_t)packet[18] << 8) | packet[19]);
+ data[2] = (((uint32_t)packet[20] << 8) | packet[21]);
+ return 0;
+}
+uint8_t MPU6050::dmpGetAccel(int16_t *data, const uint8_t* packet) {
+ // TODO: accommodate different arrangements of sent data (ONLY default supported now)
+ if (packet == 0) packet = dmpPacketBuffer;
+ data[0] = (packet[16] << 8) | packet[17];
+ data[1] = (packet[18] << 8) | packet[19];
+ data[2] = (packet[20] << 8) | packet[21];
+ return 0;
+}
+uint8_t MPU6050::dmpGetAccel(VectorInt16 *v, const uint8_t* packet) {
+ // TODO: accommodate different arrangements of sent data (ONLY default supported now)
+ if (packet == 0) packet = dmpPacketBuffer;
+ v -> x = (packet[16] << 8) | packet[17];
+ v -> y = (packet[18] << 8) | packet[19];
+ v -> z = (packet[20] << 8) | packet[21];
+ return 0;
+}
+uint8_t MPU6050::dmpGetQuaternion(int32_t *data, const uint8_t* packet) {
+ // TODO: accommodate different arrangements of sent data (ONLY default supported now)
+ if (packet == 0) packet = dmpPacketBuffer;
+ data[0] = (((uint32_t)packet[0] << 24) | ((uint32_t)packet[1] << 16) | ((uint32_t)packet[2] << 8) | packet[3]);
+ data[1] = (((uint32_t)packet[4] << 24) | ((uint32_t)packet[5] << 16) | ((uint32_t)packet[6] << 8) | packet[7]);
+ data[2] = (((uint32_t)packet[8] << 24) | ((uint32_t)packet[9] << 16) | ((uint32_t)packet[10] << 8) | packet[11]);
+ data[3] = (((uint32_t)packet[12] << 24) | ((uint32_t)packet[13] << 16) | ((uint32_t)packet[14] << 8) | packet[15]);
+ return 0;
+}
+uint8_t MPU6050::dmpGetQuaternion(int16_t *data, const uint8_t* packet) {
+ // TODO: accommodate different arrangements of sent data (ONLY default supported now)
+ if (packet == 0) packet = dmpPacketBuffer;
+ data[0] = ((packet[0] << 8) | packet[1]);
+ data[1] = ((packet[4] << 8) | packet[5]);
+ data[2] = ((packet[8] << 8) | packet[9]);
+ data[3] = ((packet[12] << 8) | packet[13]);
+ return 0;
+}
+uint8_t MPU6050::dmpGetQuaternion(Quaternion *q, const uint8_t* packet) {
+ // TODO: accommodate different arrangements of sent data (ONLY default supported now)
+ int16_t qI[4];
+ uint8_t status = dmpGetQuaternion(qI, packet);
+ if (status == 0) {
+ q -> w = (float)qI[0] / 16384.0f;
+ q -> x = (float)qI[1] / 16384.0f;
+ q -> y = (float)qI[2] / 16384.0f;
+ q -> z = (float)qI[3] / 16384.0f;
+ return 0;
+ }
+ return status; // int16 return value, indicates error if this line is reached
+}
+// uint8_t MPU6050::dmpGet6AxisQuaternion(long *data, const uint8_t* packet);
+// uint8_t MPU6050::dmpGetRelativeQuaternion(long *data, const uint8_t* packet);
+uint8_t MPU6050::dmpGetGyro(int32_t *data, const uint8_t* packet) {
+ // TODO: accommodate different arrangements of sent data (ONLY default supported now)
+ if (packet == 0) packet = dmpPacketBuffer;
+ data[0] = (((uint32_t)packet[22] << 8) | packet[23]);
+ data[1] = (((uint32_t)packet[24] << 8) | packet[25]);
+ data[2] = (((uint32_t)packet[26] << 8) | packet[27]);
+ return 0;
+}
+uint8_t MPU6050::dmpGetGyro(int16_t *data, const uint8_t* packet) {
+ // TODO: accommodate different arrangements of sent data (ONLY default supported now)
+ if (packet == 0) packet = dmpPacketBuffer;
+ data[0] = (packet[22] << 8) | packet[23];
+ data[1] = (packet[24] << 8) | packet[25];
+ data[2] = (packet[26] << 8) | packet[27];
+ return 0;
+}
+uint8_t MPU6050::dmpGetGyro(VectorInt16 *v, const uint8_t* packet) {
+ // TODO: accommodate different arrangements of sent data (ONLY default supported now)
+ if (packet == 0) packet = dmpPacketBuffer;
+ v -> x = (packet[22] << 8) | packet[23];
+ v -> y = (packet[24] << 8) | packet[25];
+ v -> z = (packet[26] << 8) | packet[27];
+ return 0;
+}
+// uint8_t MPU6050::dmpSetLinearAccelFilterCoefficient(float coef);
+// uint8_t MPU6050::dmpGetLinearAccel(long *data, const uint8_t* packet);
+uint8_t MPU6050::dmpGetLinearAccel(VectorInt16 *v, VectorInt16 *vRaw, VectorFloat *gravity) {
+ // get rid of the gravity component (+1g = +8192 in standard DMP FIFO packet, sensitivity is 2g)
+ v -> x = vRaw -> x - gravity -> x*8192;
+ v -> y = vRaw -> y - gravity -> y*8192;
+ v -> z = vRaw -> z - gravity -> z*8192;
+ return 0;
+}
+// uint8_t MPU6050::dmpGetLinearAccelInWorld(long *data, const uint8_t* packet);
+uint8_t MPU6050::dmpGetLinearAccelInWorld(VectorInt16 *v, VectorInt16 *vReal, Quaternion *q) {
+ // rotate measured 3D acceleration vector into original state
+ // frame of reference based on orientation quaternion
+ memcpy(v, vReal, sizeof(VectorInt16));
+ v -> rotate(q);
+ return 0;
+}
+// uint8_t MPU6050::dmpGetGyroAndAccelSensor(long *data, const uint8_t* packet);
+// uint8_t MPU6050::dmpGetGyroSensor(long *data, const uint8_t* packet);
+// uint8_t MPU6050::dmpGetControlData(long *data, const uint8_t* packet);
+// uint8_t MPU6050::dmpGetTemperature(long *data, const uint8_t* packet);
+// uint8_t MPU6050::dmpGetGravity(long *data, const uint8_t* packet);
+uint8_t MPU6050::dmpGetGravity(int16_t *data, const uint8_t* packet) {
+ /* +1g corresponds to +8192, sensitivity is 2g. */
+ int16_t qI[4];
+ uint8_t status = dmpGetQuaternion(qI, packet);
+ data[0] = ((int32_t)qI[1] * qI[3] - (int32_t)qI[0] * qI[2]) / 16384;
+ data[1] = ((int32_t)qI[0] * qI[1] + (int32_t)qI[2] * qI[3]) / 16384;
+ data[2] = ((int32_t)qI[0] * qI[0] - (int32_t)qI[1] * qI[1]
+ - (int32_t)qI[2] * qI[2] + (int32_t)qI[3] * qI[3]) / (2 * 16384);
+ return status;
+}
+
+uint8_t MPU6050::dmpGetGravity(VectorFloat *v, Quaternion *q) {
+ v -> x = 2 * (q -> x*q -> z - q -> w*q -> y);
+ v -> y = 2 * (q -> w*q -> x + q -> y*q -> z);
+ v -> z = q -> w*q -> w - q -> x*q -> x - q -> y*q -> y + q -> z*q -> z;
+ return 0;
+}
+// uint8_t MPU6050::dmpGetUnquantizedAccel(long *data, const uint8_t* packet);
+// uint8_t MPU6050::dmpGetQuantizedAccel(long *data, const uint8_t* packet);
+// uint8_t MPU6050::dmpGetExternalSensorData(long *data, int size, const uint8_t* packet);
+// uint8_t MPU6050::dmpGetEIS(long *data, const uint8_t* packet);
+
+uint8_t MPU6050::dmpGetEuler(float *data, Quaternion *q) {
+ data[0] = atan2(2*q -> x*q -> y - 2*q -> w*q -> z, 2*q -> w*q -> w + 2*q -> x*q -> x - 1); // psi
+ data[1] = -asin(2*q -> x*q -> z + 2*q -> w*q -> y); // theta
+ data[2] = atan2(2*q -> y*q -> z - 2*q -> w*q -> x, 2*q -> w*q -> w + 2*q -> z*q -> z - 1); // phi
+ return 0;
+}
+
+#ifdef USE_OLD_DMPGETYAWPITCHROLL
+uint8_t MPU6050::dmpGetYawPitchRoll(float *data, Quaternion *q, VectorFloat *gravity) {
+ // yaw: (about Z axis)
+ data[0] = atan2(2*q -> x*q -> y - 2*q -> w*q -> z, 2*q -> w*q -> w + 2*q -> x*q -> x - 1);
+ // pitch: (nose up/down, about Y axis)
+ data[1] = atan(gravity -> x / sqrt(gravity -> y*gravity -> y + gravity -> z*gravity -> z));
+ // roll: (tilt left/right, about X axis)
+ data[2] = atan(gravity -> y / sqrt(gravity -> x*gravity -> x + gravity -> z*gravity -> z));
+ return 0;
+}
+#else
+uint8_t MPU6050::dmpGetYawPitchRoll(float *data, Quaternion *q, VectorFloat *gravity) {
+ // yaw: (about Z axis)
+ data[0] = atan2(2*q -> x*q -> y - 2*q -> w*q -> z, 2*q -> w*q -> w + 2*q -> x*q -> x - 1);
+ // pitch: (nose up/down, about Y axis)
+ data[1] = atan2(gravity -> x , sqrt(gravity -> y*gravity -> y + gravity -> z*gravity -> z));
+ // roll: (tilt left/right, about X axis)
+ data[2] = atan2(gravity -> y , gravity -> z);
+ if (gravity -> z < 0) {
+ if(data[1] > 0) {
+ data[1] = PI - data[1];
+ } else {
+ data[1] = -PI - data[1];
+ }
+ }
+ return 0;
+}
+#endif
+
+// uint8_t MPU6050::dmpGetAccelFloat(float *data, const uint8_t* packet);
+// uint8_t MPU6050::dmpGetQuaternionFloat(float *data, const uint8_t* packet);
+
+uint8_t MPU6050::dmpProcessFIFOPacket(const unsigned char *dmpData) {
+ /*for (uint8_t k = 0; k < dmpPacketSize; k++) {
+ if (dmpData[k] < 0x10) Serial.print("0");
+ Serial.print(dmpData[k], HEX);
+ Serial.print(" ");
+ }
+ Serial.print("\n");*/
+ //Serial.println((uint16_t)dmpPacketBuffer);
+ return 0;
+}
+uint8_t MPU6050::dmpReadAndProcessFIFOPacket(uint8_t numPackets, uint8_t *processed) {
+ uint8_t status;
+ uint8_t buf[dmpPacketSize];
+ for (uint8_t i = 0; i < numPackets; i++) {
+ // read packet from FIFO
+ getFIFOBytes(buf, dmpPacketSize);
+
+ // process packet
+ if ((status = dmpProcessFIFOPacket(buf)) > 0) return status;
+
+ // increment external process count variable, if supplied
+ if (processed != 0) (*processed)++;
+ }
+ return 0;
+}
+
+// uint8_t MPU6050::dmpSetFIFOProcessedCallback(void (*func) (void));
+
+// uint8_t MPU6050::dmpInitFIFOParam();
+// uint8_t MPU6050::dmpCloseFIFO();
+// uint8_t MPU6050::dmpSetGyroDataSource(uint_fast8_t source);
+// uint8_t MPU6050::dmpDecodeQuantizedAccel();
+// uint32_t MPU6050::dmpGetGyroSumOfSquare();
+// uint32_t MPU6050::dmpGetAccelSumOfSquare();
+// void MPU6050::dmpOverrideQuaternion(long *q);
+uint16_t MPU6050::dmpGetFIFOPacketSize() {
+ return dmpPacketSize;
+}
+
+#endif /* _MPU6050_6AXIS_MOTIONAPPS20_H_ */
diff --git a/Versions/dRehmFlight_ESP32_BETA_1.3/src/MPU6050/MPU6050_9Axis_MotionApps41.h b/Versions/dRehmFlight_ESP32_BETA_1.3/src/MPU6050/MPU6050_9Axis_MotionApps41.h
new file mode 100644
index 00000000..763a49b9
--- /dev/null
+++ b/Versions/dRehmFlight_ESP32_BETA_1.3/src/MPU6050/MPU6050_9Axis_MotionApps41.h
@@ -0,0 +1,887 @@
+// I2Cdev library collection - MPU6050 I2C device class, 9-axis MotionApps 4.1 implementation
+// Based on InvenSense MPU-6050 register map document rev. 2.0, 5/19/2011 (RM-MPU-6000A-00)
+// 6/18/2012 by Jeff Rowberg
+// Updates should (hopefully) always be available at https://github.com/jrowberg/i2cdevlib
+//
+// Changelog:
+// ... - ongoing debug release
+
+/* ============================================
+I2Cdev device library code is placed under the MIT license
+Copyright (c) 2012 Jeff Rowberg
+
+Permission is hereby granted, free of charge, to any person obtaining a copy
+of this software and associated documentation files (the "Software"), to deal
+in the Software without restriction, including without limitation the rights
+to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+copies of the Software, and to permit persons to whom the Software is
+furnished to do so, subject to the following conditions:
+
+The above copyright notice and this permission notice shall be included in
+all copies or substantial portions of the Software.
+
+THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+THE SOFTWARE.
+===============================================
+*/
+
+#ifndef _MPU6050_9AXIS_MOTIONAPPS41_H_
+#define _MPU6050_9AXIS_MOTIONAPPS41_H_
+
+#include "I2Cdev.h"
+#include "helper_3dmath.h"
+
+// MotionApps 4.1 DMP implementation, built using the MPU-9150 "MotionFit" board
+#define MPU6050_INCLUDE_DMP_MOTIONAPPS41
+
+#include "MPU6050.h"
+
+// Tom Carpenter's conditional PROGMEM code
+// http://forum.arduino.cc/index.php?topic=129407.0
+#ifdef __AVR__
+ #include
+#else
+ // Teensy 3.0 library conditional PROGMEM code from Paul Stoffregen
+ #ifndef __PGMSPACE_H_
+ #define __PGMSPACE_H_ 1
+ #include
+
+ #define PROGMEM
+ #define PGM_P const char *
+ #define PSTR(str) (str)
+ #define F(x) x
+
+ typedef void prog_void;
+ typedef char prog_char;
+ //typedef unsigned char prog_uchar;
+ typedef int8_t prog_int8_t;
+ typedef uint8_t prog_uint8_t;
+ typedef int16_t prog_int16_t;
+ typedef uint16_t prog_uint16_t;
+ typedef int32_t prog_int32_t;
+ typedef uint32_t prog_uint32_t;
+
+ #define strcpy_P(dest, src) strcpy((dest), (src))
+ #define strcat_P(dest, src) strcat((dest), (src))
+ #define strcmp_P(a, b) strcmp((a), (b))
+
+ #define pgm_read_byte(addr) (*(const unsigned char *)(addr))
+ #define pgm_read_word(addr) (*(const unsigned short *)(addr))
+ #define pgm_read_dword(addr) (*(const unsigned long *)(addr))
+ #define pgm_read_float(addr) (*(const float *)(addr))
+
+ #define pgm_read_byte_near(addr) pgm_read_byte(addr)
+ #define pgm_read_word_near(addr) pgm_read_word(addr)
+ #define pgm_read_dword_near(addr) pgm_read_dword(addr)
+ #define pgm_read_float_near(addr) pgm_read_float(addr)
+ #define pgm_read_byte_far(addr) pgm_read_byte(addr)
+ #define pgm_read_word_far(addr) pgm_read_word(addr)
+ #define pgm_read_dword_far(addr) pgm_read_dword(addr)
+ #define pgm_read_float_far(addr) pgm_read_float(addr)
+ #endif
+#endif
+
+// NOTE! Enabling DEBUG adds about 3.3kB to the flash program size.
+// Debug output is now working even on ATMega328P MCUs (e.g. Arduino Uno)
+// after moving string constants to flash memory storage using the F()
+// compiler macro (Arduino IDE 1.0+ required).
+
+//#define DEBUG
+#ifdef DEBUG
+ #define DEBUG_PRINT(x) Serial.print(x)
+ #define DEBUG_PRINTF(x, y) Serial.print(x, y)
+ #define DEBUG_PRINTLN(x) Serial.println(x)
+ #define DEBUG_PRINTLNF(x, y) Serial.println(x, y)
+#else
+ #define DEBUG_PRINT(x)
+ #define DEBUG_PRINTF(x, y)
+ #define DEBUG_PRINTLN(x)
+ #define DEBUG_PRINTLNF(x, y)
+#endif
+
+#define MPU6050_DMP_CODE_SIZE 1962 // dmpMemory[]
+#define MPU6050_DMP_CONFIG_SIZE 232 // dmpConfig[]
+#define MPU6050_DMP_UPDATES_SIZE 140 // dmpUpdates[]
+
+/* ================================================================================================ *
+ | Default MotionApps v4.1 48-byte FIFO packet structure: |
+ | |
+ | [QUAT W][ ][QUAT X][ ][QUAT Y][ ][QUAT Z][ ][GYRO X][ ][GYRO Y][ ] |
+ | 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 |
+ | |
+ | [GYRO Z][ ][MAG X ][MAG Y ][MAG Z ][ACC X ][ ][ACC Y ][ ][ACC Z ][ ][ ] |
+ | 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 |
+ * ================================================================================================ */
+
+// this block of memory gets written to the MPU on start-up, and it seems
+// to be volatile memory, so it has to be done each time (it only takes ~1
+// second though)
+const unsigned char dmpMemory[MPU6050_DMP_CODE_SIZE] PROGMEM = {
+ // bank 0, 256 bytes
+ 0xFB, 0x00, 0x00, 0x3E, 0x00, 0x0B, 0x00, 0x36, 0x00, 0x01, 0x00, 0x02, 0x00, 0x03, 0x00, 0x00,
+ 0x00, 0x65, 0x00, 0x54, 0xFF, 0xEF, 0x00, 0x00, 0xFA, 0x80, 0x00, 0x0B, 0x12, 0x82, 0x00, 0x01,
+ 0x00, 0x02, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+ 0x00, 0x28, 0x00, 0x00, 0xFF, 0xFF, 0x45, 0x81, 0xFF, 0xFF, 0xFA, 0x72, 0x00, 0x00, 0x00, 0x00,
+ 0x00, 0x00, 0x03, 0xE8, 0x00, 0x00, 0x00, 0x01, 0x00, 0x01, 0x7F, 0xFF, 0xFF, 0xFE, 0x80, 0x01,
+ 0x00, 0x1B, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+ 0x00, 0x3E, 0x03, 0x30, 0x40, 0x00, 0x00, 0x00, 0x02, 0xCA, 0xE3, 0x09, 0x3E, 0x80, 0x00, 0x00,
+ 0x20, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x40, 0x00, 0x00, 0x00, 0x60, 0x00, 0x00, 0x00,
+ 0x41, 0xFF, 0x00, 0x00, 0x00, 0x00, 0x0B, 0x2A, 0x00, 0x00, 0x16, 0x55, 0x00, 0x00, 0x21, 0x82,
+ 0xFD, 0x87, 0x26, 0x50, 0xFD, 0x80, 0x00, 0x00, 0x00, 0x1F, 0x00, 0x00, 0x00, 0x05, 0x80, 0x00,
+ 0x00, 0x00, 0x00, 0x00, 0x00, 0x01, 0x00, 0x00, 0x00, 0x02, 0x00, 0x00, 0x00, 0x03, 0x00, 0x00,
+ 0x40, 0x00, 0x00, 0x00, 0x00, 0x00, 0x04, 0x6F, 0x00, 0x02, 0x65, 0x32, 0x00, 0x00, 0x5E, 0xC0,
+ 0x40, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+ 0xFB, 0x8C, 0x6F, 0x5D, 0xFD, 0x5D, 0x08, 0xD9, 0x00, 0x7C, 0x73, 0x3B, 0x00, 0x6C, 0x12, 0xCC,
+ 0x32, 0x00, 0x13, 0x9D, 0x32, 0x00, 0xD0, 0xD6, 0x32, 0x00, 0x08, 0x00, 0x40, 0x00, 0x01, 0xF4,
+ 0xFF, 0xE6, 0x80, 0x79, 0x02, 0x00, 0x00, 0x00, 0x00, 0x00, 0xD0, 0xD6, 0x00, 0x00, 0x27, 0x10,
+
+ // bank 1, 256 bytes
+ 0xFB, 0x00, 0x00, 0x00, 0x40, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+ 0x00, 0x00, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x01, 0x00, 0x01, 0x00, 0x00, 0x00,
+ 0x00, 0x00, 0xFA, 0x36, 0xFF, 0xBC, 0x30, 0x8E, 0x00, 0x05, 0xFB, 0xF0, 0xFF, 0xD9, 0x5B, 0xC8,
+ 0xFF, 0xD0, 0x9A, 0xBE, 0x00, 0x00, 0x10, 0xA9, 0xFF, 0xF4, 0x1E, 0xB2, 0x00, 0xCE, 0xBB, 0xF7,
+ 0x00, 0x00, 0x00, 0x01, 0x00, 0x00, 0x00, 0x04, 0x00, 0x02, 0x00, 0x02, 0x02, 0x00, 0x00, 0x0C,
+ 0xFF, 0xC2, 0x80, 0x00, 0x00, 0x01, 0x80, 0x00, 0x00, 0xCF, 0x80, 0x00, 0x40, 0x00, 0x00, 0x00,
+ 0x00, 0x00, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x06, 0x00, 0x00, 0x00, 0x00, 0x14,
+ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+ 0x00, 0x00, 0x00, 0x00, 0x03, 0x3F, 0x68, 0xB6, 0x79, 0x35, 0x28, 0xBC, 0xC6, 0x7E, 0xD1, 0x6C,
+ 0x80, 0x00, 0x00, 0x00, 0x40, 0x00, 0x00, 0x00, 0x00, 0x00, 0xB2, 0x6A, 0x00, 0x00, 0x00, 0x00,
+ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x3F, 0xF0, 0x00, 0x00, 0x00, 0x30,
+ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+ 0x00, 0x00, 0x25, 0x4D, 0x00, 0x2F, 0x70, 0x6D, 0x00, 0x00, 0x05, 0xAE, 0x00, 0x0C, 0x02, 0xD0,
+
+ // bank 2, 256 bytes
+ 0x00, 0x00, 0x00, 0x00, 0x00, 0x65, 0x00, 0x54, 0xFF, 0xEF, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+ 0x00, 0x00, 0x01, 0x00, 0x00, 0x44, 0x00, 0x00, 0x00, 0x00, 0x0C, 0x00, 0x00, 0x00, 0x01, 0x00,
+ 0x00, 0x00, 0x00, 0x00, 0x00, 0x65, 0x00, 0x00, 0x00, 0x54, 0x00, 0x00, 0xFF, 0xEF, 0x00, 0x00,
+ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+ 0x40, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+ 0x40, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+ 0x00, 0x00, 0x00, 0x01, 0x00, 0x00, 0x00, 0x02, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+ 0x00, 0x1B, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x40, 0x00, 0x00, 0x00,
+ 0x00, 0x1B, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x47, 0x78, 0xA2,
+ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+
+ // bank 3, 256 bytes
+ 0xD8, 0xDC, 0xF4, 0xD8, 0xB9, 0xAB, 0xF3, 0xF8, 0xFA, 0xF1, 0xBA, 0xA2, 0xDE, 0xB2, 0xB8, 0xB4,
+ 0xA8, 0x81, 0x98, 0xF7, 0x4A, 0x90, 0x7F, 0x91, 0x6A, 0xF3, 0xF9, 0xDB, 0xA8, 0xF9, 0xB0, 0xBA,
+ 0xA0, 0x80, 0xF2, 0xCE, 0x81, 0xF3, 0xC2, 0xF1, 0xC1, 0xF2, 0xC3, 0xF3, 0xCC, 0xA2, 0xB2, 0x80,
+ 0xF1, 0xC6, 0xD8, 0x80, 0xBA, 0xA7, 0xDF, 0xDF, 0xDF, 0xF2, 0xA7, 0xC3, 0xCB, 0xC5, 0xB6, 0xF0,
+ 0x87, 0xA2, 0x94, 0x24, 0x48, 0x70, 0x3C, 0x95, 0x40, 0x68, 0x34, 0x58, 0x9B, 0x78, 0xA2, 0xF1,
+ 0x83, 0x92, 0x2D, 0x55, 0x7D, 0xD8, 0xB1, 0xB4, 0xB8, 0xA1, 0xD0, 0x91, 0x80, 0xF2, 0x70, 0xF3,
+ 0x70, 0xF2, 0x7C, 0x80, 0xA8, 0xF1, 0x01, 0xB0, 0x98, 0x87, 0xD9, 0x43, 0xD8, 0x86, 0xC9, 0x88,
+ 0xBA, 0xA1, 0xF2, 0x0E, 0xB8, 0x97, 0x80, 0xF1, 0xA9, 0xDF, 0xDF, 0xDF, 0xAA, 0xDF, 0xDF, 0xDF,
+ 0xF2, 0xAA, 0xC5, 0xCD, 0xC7, 0xA9, 0x0C, 0xC9, 0x2C, 0x97, 0x97, 0x97, 0x97, 0xF1, 0xA9, 0x89,
+ 0x26, 0x46, 0x66, 0xB0, 0xB4, 0xBA, 0x80, 0xAC, 0xDE, 0xF2, 0xCA, 0xF1, 0xB2, 0x8C, 0x02, 0xA9,
+ 0xB6, 0x98, 0x00, 0x89, 0x0E, 0x16, 0x1E, 0xB8, 0xA9, 0xB4, 0x99, 0x2C, 0x54, 0x7C, 0xB0, 0x8A,
+ 0xA8, 0x96, 0x36, 0x56, 0x76, 0xF1, 0xB9, 0xAF, 0xB4, 0xB0, 0x83, 0xC0, 0xB8, 0xA8, 0x97, 0x11,
+ 0xB1, 0x8F, 0x98, 0xB9, 0xAF, 0xF0, 0x24, 0x08, 0x44, 0x10, 0x64, 0x18, 0xF1, 0xA3, 0x29, 0x55,
+ 0x7D, 0xAF, 0x83, 0xB5, 0x93, 0xF0, 0x00, 0x28, 0x50, 0xF5, 0xBA, 0xAD, 0x8F, 0x9F, 0x28, 0x54,
+ 0x7C, 0xB9, 0xF1, 0xA3, 0x86, 0x9F, 0x61, 0xA6, 0xDA, 0xDE, 0xDF, 0xDB, 0xB2, 0xB6, 0x8E, 0x9D,
+ 0xAE, 0xF5, 0x60, 0x68, 0x70, 0xB1, 0xB5, 0xF1, 0xDA, 0xA6, 0xDF, 0xD9, 0xA6, 0xFA, 0xA3, 0x86,
+
+ // bank 4, 256 bytes
+ 0x96, 0xDB, 0x31, 0xA6, 0xD9, 0xF8, 0xDF, 0xBA, 0xA6, 0x8F, 0xC2, 0xC5, 0xC7, 0xB2, 0x8C, 0xC1,
+ 0xB8, 0xA2, 0xDF, 0xDF, 0xDF, 0xA3, 0xDF, 0xDF, 0xDF, 0xD8, 0xD8, 0xF1, 0xB8, 0xA8, 0xB2, 0x86,
+ 0xB4, 0x98, 0x0D, 0x35, 0x5D, 0xB8, 0xAA, 0x98, 0xB0, 0x87, 0x2D, 0x35, 0x3D, 0xB2, 0xB6, 0xBA,
+ 0xAF, 0x8C, 0x96, 0x19, 0x8F, 0x9F, 0xA7, 0x0E, 0x16, 0x1E, 0xB4, 0x9A, 0xB8, 0xAA, 0x87, 0x2C,
+ 0x54, 0x7C, 0xB9, 0xA3, 0xDE, 0xDF, 0xDF, 0xA3, 0xB1, 0x80, 0xF2, 0xC4, 0xCD, 0xC9, 0xF1, 0xB8,
+ 0xA9, 0xB4, 0x99, 0x83, 0x0D, 0x35, 0x5D, 0x89, 0xB9, 0xA3, 0x2D, 0x55, 0x7D, 0xB5, 0x93, 0xA3,
+ 0x0E, 0x16, 0x1E, 0xA9, 0x2C, 0x54, 0x7C, 0xB8, 0xB4, 0xB0, 0xF1, 0x97, 0x83, 0xA8, 0x11, 0x84,
+ 0xA5, 0x09, 0x98, 0xA3, 0x83, 0xF0, 0xDA, 0x24, 0x08, 0x44, 0x10, 0x64, 0x18, 0xD8, 0xF1, 0xA5,
+ 0x29, 0x55, 0x7D, 0xA5, 0x85, 0x95, 0x02, 0x1A, 0x2E, 0x3A, 0x56, 0x5A, 0x40, 0x48, 0xF9, 0xF3,
+ 0xA3, 0xD9, 0xF8, 0xF0, 0x98, 0x83, 0x24, 0x08, 0x44, 0x10, 0x64, 0x18, 0x97, 0x82, 0xA8, 0xF1,
+ 0x11, 0xF0, 0x98, 0xA2, 0x24, 0x08, 0x44, 0x10, 0x64, 0x18, 0xDA, 0xF3, 0xDE, 0xD8, 0x83, 0xA5,
+ 0x94, 0x01, 0xD9, 0xA3, 0x02, 0xF1, 0xA2, 0xC3, 0xC5, 0xC7, 0xD8, 0xF1, 0x84, 0x92, 0xA2, 0x4D,
+ 0xDA, 0x2A, 0xD8, 0x48, 0x69, 0xD9, 0x2A, 0xD8, 0x68, 0x55, 0xDA, 0x32, 0xD8, 0x50, 0x71, 0xD9,
+ 0x32, 0xD8, 0x70, 0x5D, 0xDA, 0x3A, 0xD8, 0x58, 0x79, 0xD9, 0x3A, 0xD8, 0x78, 0x93, 0xA3, 0x4D,
+ 0xDA, 0x2A, 0xD8, 0x48, 0x69, 0xD9, 0x2A, 0xD8, 0x68, 0x55, 0xDA, 0x32, 0xD8, 0x50, 0x71, 0xD9,
+ 0x32, 0xD8, 0x70, 0x5D, 0xDA, 0x3A, 0xD8, 0x58, 0x79, 0xD9, 0x3A, 0xD8, 0x78, 0xA8, 0x8A, 0x9A,
+
+ // bank 5, 256 bytes
+ 0xF0, 0x28, 0x50, 0x78, 0x9E, 0xF3, 0x88, 0x18, 0xF1, 0x9F, 0x1D, 0x98, 0xA8, 0xD9, 0x08, 0xD8,
+ 0xC8, 0x9F, 0x12, 0x9E, 0xF3, 0x15, 0xA8, 0xDA, 0x12, 0x10, 0xD8, 0xF1, 0xAF, 0xC8, 0x97, 0x87,
+ 0x34, 0xB5, 0xB9, 0x94, 0xA4, 0x21, 0xF3, 0xD9, 0x22, 0xD8, 0xF2, 0x2D, 0xF3, 0xD9, 0x2A, 0xD8,
+ 0xF2, 0x35, 0xF3, 0xD9, 0x32, 0xD8, 0x81, 0xA4, 0x60, 0x60, 0x61, 0xD9, 0x61, 0xD8, 0x6C, 0x68,
+ 0x69, 0xD9, 0x69, 0xD8, 0x74, 0x70, 0x71, 0xD9, 0x71, 0xD8, 0xB1, 0xA3, 0x84, 0x19, 0x3D, 0x5D,
+ 0xA3, 0x83, 0x1A, 0x3E, 0x5E, 0x93, 0x10, 0x30, 0x81, 0x10, 0x11, 0xB8, 0xB0, 0xAF, 0x8F, 0x94,
+ 0xF2, 0xDA, 0x3E, 0xD8, 0xB4, 0x9A, 0xA8, 0x87, 0x29, 0xDA, 0xF8, 0xD8, 0x87, 0x9A, 0x35, 0xDA,
+ 0xF8, 0xD8, 0x87, 0x9A, 0x3D, 0xDA, 0xF8, 0xD8, 0xB1, 0xB9, 0xA4, 0x98, 0x85, 0x02, 0x2E, 0x56,
+ 0xA5, 0x81, 0x00, 0x0C, 0x14, 0xA3, 0x97, 0xB0, 0x8A, 0xF1, 0x2D, 0xD9, 0x28, 0xD8, 0x4D, 0xD9,
+ 0x48, 0xD8, 0x6D, 0xD9, 0x68, 0xD8, 0xB1, 0x84, 0x0D, 0xDA, 0x0E, 0xD8, 0xA3, 0x29, 0x83, 0xDA,
+ 0x2C, 0x0E, 0xD8, 0xA3, 0x84, 0x49, 0x83, 0xDA, 0x2C, 0x4C, 0x0E, 0xD8, 0xB8, 0xB0, 0x97, 0x86,
+ 0xA8, 0x31, 0x9B, 0x06, 0x99, 0x07, 0xAB, 0x97, 0x28, 0x88, 0x9B, 0xF0, 0x0C, 0x20, 0x14, 0x40,
+ 0xB9, 0xA3, 0x8A, 0xC3, 0xC5, 0xC7, 0x9A, 0xA3, 0x28, 0x50, 0x78, 0xF1, 0xB5, 0x93, 0x01, 0xD9,
+ 0xDF, 0xDF, 0xDF, 0xD8, 0xB8, 0xB4, 0xA8, 0x8C, 0x9C, 0xF0, 0x04, 0x28, 0x51, 0x79, 0x1D, 0x30,
+ 0x14, 0x38, 0xB2, 0x82, 0xAB, 0xD0, 0x98, 0x2C, 0x50, 0x50, 0x78, 0x78, 0x9B, 0xF1, 0x1A, 0xB0,
+ 0xF0, 0xB1, 0x83, 0x9C, 0xA8, 0x29, 0x51, 0x79, 0xB0, 0x8B, 0x29, 0x51, 0x79, 0xB1, 0x83, 0x24,
+
+ // bank 6, 256 bytes
+ 0x70, 0x59, 0xB0, 0x8B, 0x20, 0x58, 0x71, 0xB1, 0x83, 0x44, 0x69, 0x38, 0xB0, 0x8B, 0x39, 0x40,
+ 0x68, 0xB1, 0x83, 0x64, 0x48, 0x31, 0xB0, 0x8B, 0x30, 0x49, 0x60, 0xA5, 0x88, 0x20, 0x09, 0x71,
+ 0x58, 0x44, 0x68, 0x11, 0x39, 0x64, 0x49, 0x30, 0x19, 0xF1, 0xAC, 0x00, 0x2C, 0x54, 0x7C, 0xF0,
+ 0x8C, 0xA8, 0x04, 0x28, 0x50, 0x78, 0xF1, 0x88, 0x97, 0x26, 0xA8, 0x59, 0x98, 0xAC, 0x8C, 0x02,
+ 0x26, 0x46, 0x66, 0xF0, 0x89, 0x9C, 0xA8, 0x29, 0x51, 0x79, 0x24, 0x70, 0x59, 0x44, 0x69, 0x38,
+ 0x64, 0x48, 0x31, 0xA9, 0x88, 0x09, 0x20, 0x59, 0x70, 0xAB, 0x11, 0x38, 0x40, 0x69, 0xA8, 0x19,
+ 0x31, 0x48, 0x60, 0x8C, 0xA8, 0x3C, 0x41, 0x5C, 0x20, 0x7C, 0x00, 0xF1, 0x87, 0x98, 0x19, 0x86,
+ 0xA8, 0x6E, 0x76, 0x7E, 0xA9, 0x99, 0x88, 0x2D, 0x55, 0x7D, 0x9E, 0xB9, 0xA3, 0x8A, 0x22, 0x8A,
+ 0x6E, 0x8A, 0x56, 0x8A, 0x5E, 0x9F, 0xB1, 0x83, 0x06, 0x26, 0x46, 0x66, 0x0E, 0x2E, 0x4E, 0x6E,
+ 0x9D, 0xB8, 0xAD, 0x00, 0x2C, 0x54, 0x7C, 0xF2, 0xB1, 0x8C, 0xB4, 0x99, 0xB9, 0xA3, 0x2D, 0x55,
+ 0x7D, 0x81, 0x91, 0xAC, 0x38, 0xAD, 0x3A, 0xB5, 0x83, 0x91, 0xAC, 0x2D, 0xD9, 0x28, 0xD8, 0x4D,
+ 0xD9, 0x48, 0xD8, 0x6D, 0xD9, 0x68, 0xD8, 0x8C, 0x9D, 0xAE, 0x29, 0xD9, 0x04, 0xAE, 0xD8, 0x51,
+ 0xD9, 0x04, 0xAE, 0xD8, 0x79, 0xD9, 0x04, 0xD8, 0x81, 0xF3, 0x9D, 0xAD, 0x00, 0x8D, 0xAE, 0x19,
+ 0x81, 0xAD, 0xD9, 0x01, 0xD8, 0xF2, 0xAE, 0xDA, 0x26, 0xD8, 0x8E, 0x91, 0x29, 0x83, 0xA7, 0xD9,
+ 0xAD, 0xAD, 0xAD, 0xAD, 0xF3, 0x2A, 0xD8, 0xD8, 0xF1, 0xB0, 0xAC, 0x89, 0x91, 0x3E, 0x5E, 0x76,
+ 0xF3, 0xAC, 0x2E, 0x2E, 0xF1, 0xB1, 0x8C, 0x5A, 0x9C, 0xAC, 0x2C, 0x28, 0x28, 0x28, 0x9C, 0xAC,
+
+ // bank 7, 170 bytes (remainder)
+ 0x30, 0x18, 0xA8, 0x98, 0x81, 0x28, 0x34, 0x3C, 0x97, 0x24, 0xA7, 0x28, 0x34, 0x3C, 0x9C, 0x24,
+ 0xF2, 0xB0, 0x89, 0xAC, 0x91, 0x2C, 0x4C, 0x6C, 0x8A, 0x9B, 0x2D, 0xD9, 0xD8, 0xD8, 0x51, 0xD9,
+ 0xD8, 0xD8, 0x79, 0xD9, 0xD8, 0xD8, 0xF1, 0x9E, 0x88, 0xA3, 0x31, 0xDA, 0xD8, 0xD8, 0x91, 0x2D,
+ 0xD9, 0x28, 0xD8, 0x4D, 0xD9, 0x48, 0xD8, 0x6D, 0xD9, 0x68, 0xD8, 0xB1, 0x83, 0x93, 0x35, 0x3D,
+ 0x80, 0x25, 0xDA, 0xD8, 0xD8, 0x85, 0x69, 0xDA, 0xD8, 0xD8, 0xB4, 0x93, 0x81, 0xA3, 0x28, 0x34,
+ 0x3C, 0xF3, 0xAB, 0x8B, 0xA3, 0x91, 0xB6, 0x09, 0xB4, 0xD9, 0xAB, 0xDE, 0xB0, 0x87, 0x9C, 0xB9,
+ 0xA3, 0xDD, 0xF1, 0xA3, 0xA3, 0xA3, 0xA3, 0x95, 0xF1, 0xA3, 0xA3, 0xA3, 0x9D, 0xF1, 0xA3, 0xA3,
+ 0xA3, 0xA3, 0xF2, 0xA3, 0xB4, 0x90, 0x80, 0xF2, 0xA3, 0xA3, 0xA3, 0xA3, 0xA3, 0xA3, 0xA3, 0xA3,
+ 0xA3, 0xA3, 0xB2, 0xA3, 0xA3, 0xA3, 0xA3, 0xA3, 0xA3, 0xB0, 0x87, 0xB5, 0x99, 0xF1, 0xA3, 0xA3,
+ 0xA3, 0x98, 0xF1, 0xA3, 0xA3, 0xA3, 0xA3, 0x97, 0xA3, 0xA3, 0xA3, 0xA3, 0xF3, 0x9B, 0xA3, 0xA3,
+ 0xDC, 0xB9, 0xA7, 0xF1, 0x26, 0x26, 0x26, 0xD8, 0xD8, 0xFF
+};
+
+#ifndef MPU6050_DMP_FIFO_RATE_DIVISOR
+#define MPU6050_DMP_FIFO_RATE_DIVISOR 0x03
+#endif
+
+const unsigned char dmpConfig[MPU6050_DMP_CONFIG_SIZE] PROGMEM = {
+// BANK OFFSET LENGTH [DATA]
+ 0x02, 0xEC, 0x04, 0x00, 0x47, 0x7D, 0x1A, // ?
+ 0x03, 0x82, 0x03, 0x4C, 0xCD, 0x6C, // FCFG_1 inv_set_gyro_calibration
+ 0x03, 0xB2, 0x03, 0x36, 0x56, 0x76, // FCFG_3 inv_set_gyro_calibration
+ 0x00, 0x68, 0x04, 0x02, 0xCA, 0xE3, 0x09, // D_0_104 inv_set_gyro_calibration
+ 0x01, 0x0C, 0x04, 0x00, 0x00, 0x00, 0x00, // D_1_152 inv_set_accel_calibration
+ 0x03, 0x86, 0x03, 0x0C, 0xC9, 0x2C, // FCFG_2 inv_set_accel_calibration
+ 0x03, 0x90, 0x03, 0x26, 0x46, 0x66, // (continued)...FCFG_2 inv_set_accel_calibration
+ 0x00, 0x6C, 0x02, 0x40, 0x00, // D_0_108 inv_set_accel_calibration
+
+ 0x02, 0x40, 0x04, 0x00, 0x00, 0x00, 0x00, // CPASS_MTX_00 inv_set_compass_calibration
+ 0x02, 0x44, 0x04, 0x40, 0x00, 0x00, 0x00, // CPASS_MTX_01
+ 0x02, 0x48, 0x04, 0x00, 0x00, 0x00, 0x00, // CPASS_MTX_02
+ 0x02, 0x4C, 0x04, 0x40, 0x00, 0x00, 0x00, // CPASS_MTX_10
+ 0x02, 0x50, 0x04, 0x00, 0x00, 0x00, 0x00, // CPASS_MTX_11
+ 0x02, 0x54, 0x04, 0x00, 0x00, 0x00, 0x00, // CPASS_MTX_12
+ 0x02, 0x58, 0x04, 0x00, 0x00, 0x00, 0x00, // CPASS_MTX_20
+ 0x02, 0x5C, 0x04, 0x00, 0x00, 0x00, 0x00, // CPASS_MTX_21
+ 0x02, 0xBC, 0x04, 0xC0, 0x00, 0x00, 0x00, // CPASS_MTX_22
+
+ 0x01, 0xEC, 0x04, 0x00, 0x00, 0x40, 0x00, // D_1_236 inv_apply_endian_accel
+ 0x03, 0x86, 0x06, 0x0C, 0xC9, 0x2C, 0x97, 0x97, 0x97, // FCFG_2 inv_set_mpu_sensors
+ 0x04, 0x22, 0x03, 0x0D, 0x35, 0x5D, // CFG_MOTION_BIAS inv_turn_on_bias_from_no_motion
+ 0x00, 0xA3, 0x01, 0x00, // ?
+ 0x04, 0x29, 0x04, 0x87, 0x2D, 0x35, 0x3D, // FCFG_5 inv_set_bias_update
+ 0x07, 0x62, 0x05, 0xF1, 0x20, 0x28, 0x30, 0x38, // CFG_8 inv_send_quaternion
+ 0x07, 0x9F, 0x01, 0x30, // CFG_16 inv_set_footer
+ 0x07, 0x67, 0x01, 0x9A, // CFG_GYRO_SOURCE inv_send_gyro
+ 0x07, 0x68, 0x04, 0xF1, 0x28, 0x30, 0x38, // CFG_9 inv_send_gyro -> inv_construct3_fifo
+ 0x07, 0x62, 0x05, 0xF1, 0x20, 0x28, 0x30, 0x38, // ?
+ 0x02, 0x0C, 0x04, 0x00, 0x00, 0x00, 0x00, // ?
+ 0x07, 0x83, 0x06, 0xC2, 0xCA, 0xC4, 0xA3, 0xA3, 0xA3, // ?
+ // SPECIAL 0x01 = enable interrupts
+ 0x00, 0x00, 0x00, 0x01, // SET INT_ENABLE, SPECIAL INSTRUCTION
+ 0x07, 0xA7, 0x01, 0xFE, // ?
+ 0x07, 0x62, 0x05, 0xF1, 0x20, 0x28, 0x30, 0x38, // ?
+ 0x07, 0x67, 0x01, 0x9A, // ?
+ 0x07, 0x68, 0x04, 0xF1, 0x28, 0x30, 0x38, // CFG_12 inv_send_accel -> inv_construct3_fifo
+ 0x07, 0x8D, 0x04, 0xF1, 0x28, 0x30, 0x38, // ??? CFG_12 inv_send_mag -> inv_construct3_fifo
+ 0x02, 0x16, 0x02, 0x00, MPU6050_DMP_FIFO_RATE_DIVISOR // D_0_22 inv_set_fifo_rate
+
+ // This very last 0x03 WAS a 0x09, which drops the FIFO rate down to 20 Hz. 0x07 is 25 Hz,
+ // 0x01 is 100Hz. Going faster than 100Hz (0x00=200Hz) tends to result in very noisy data.
+ // DMP output frequency is calculated easily using this equation: (200Hz / (1 + value))
+
+ // It is important to make sure the host processor can keep up with reading and processing
+ // the FIFO output at the desired rate. Handling FIFO overflow cleanly is also a good idea.
+};
+
+const unsigned char dmpUpdates[MPU6050_DMP_UPDATES_SIZE] PROGMEM = {
+ 0x01, 0xB2, 0x02, 0xFF, 0xF5,
+ 0x01, 0x90, 0x04, 0x0A, 0x0D, 0x97, 0xC0,
+ 0x00, 0xA3, 0x01, 0x00,
+ 0x04, 0x29, 0x04, 0x87, 0x2D, 0x35, 0x3D,
+ 0x01, 0x6A, 0x02, 0x06, 0x00,
+ 0x01, 0x60, 0x08, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+ 0x00, 0x60, 0x04, 0x40, 0x00, 0x00, 0x00,
+ 0x02, 0x60, 0x0C, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+ 0x01, 0x08, 0x02, 0x01, 0x20,
+ 0x01, 0x0A, 0x02, 0x00, 0x4E,
+ 0x01, 0x02, 0x02, 0xFE, 0xB3,
+ 0x02, 0x6C, 0x04, 0x00, 0x00, 0x00, 0x00, // READ
+ 0x02, 0x6C, 0x04, 0xFA, 0xFE, 0x00, 0x00,
+ 0x02, 0x60, 0x0C, 0xFF, 0xFF, 0xCB, 0x4D, 0x00, 0x01, 0x08, 0xC1, 0xFF, 0xFF, 0xBC, 0x2C,
+ 0x02, 0xF4, 0x04, 0x00, 0x00, 0x00, 0x00,
+ 0x02, 0xF8, 0x04, 0x00, 0x00, 0x00, 0x00,
+ 0x02, 0xFC, 0x04, 0x00, 0x00, 0x00, 0x00,
+ 0x00, 0x60, 0x04, 0x40, 0x00, 0x00, 0x00,
+ 0x00, 0x60, 0x04, 0x00, 0x40, 0x00, 0x00
+};
+
+uint8_t MPU6050::dmpInitialize() {
+ // reset device
+ DEBUG_PRINTLN(F("\n\nResetting MPU6050..."));
+ reset();
+ delay(30); // wait after reset
+
+ // disable sleep mode
+ DEBUG_PRINTLN(F("Disabling sleep mode..."));
+ setSleepEnabled(false);
+
+ // get MPU product ID
+ DEBUG_PRINTLN(F("Getting product ID..."));
+ //uint8_t productID = 0; //getProductID();
+ DEBUG_PRINT(F("Product ID = "));
+ DEBUG_PRINT(productID);
+
+ // get MPU hardware revision
+ DEBUG_PRINTLN(F("Selecting user bank 16..."));
+ setMemoryBank(0x10, true, true);
+ DEBUG_PRINTLN(F("Selecting memory byte 6..."));
+ setMemoryStartAddress(0x06);
+ DEBUG_PRINTLN(F("Checking hardware revision..."));
+ uint8_t hwRevision = readMemoryByte();
+ DEBUG_PRINT(F("Revision @ user[16][6] = "));
+ DEBUG_PRINTLNF(hwRevision, HEX);
+ DEBUG_PRINTLN(F("Resetting memory bank selection to 0..."));
+ setMemoryBank(0, false, false);
+
+ // check OTP bank valid
+ DEBUG_PRINTLN(F("Reading OTP bank valid flag..."));
+ uint8_t otpValid = getOTPBankValid();
+ DEBUG_PRINT(F("OTP bank is "));
+ DEBUG_PRINTLN(otpValid ? F("valid!") : F("invalid!"));
+
+ // get X/Y/Z gyro offsets
+ DEBUG_PRINTLN(F("Reading gyro offset values..."));
+ int8_t xgOffset = getXGyroOffset();
+ int8_t ygOffset = getYGyroOffset();
+ int8_t zgOffset = getZGyroOffset();
+ DEBUG_PRINT(F("X gyro offset = "));
+ DEBUG_PRINTLN(xgOffset);
+ DEBUG_PRINT(F("Y gyro offset = "));
+ DEBUG_PRINTLN(ygOffset);
+ DEBUG_PRINT(F("Z gyro offset = "));
+ DEBUG_PRINTLN(zgOffset);
+
+ I2Cdev::readByte(devAddr, MPU6050_RA_USER_CTRL, buffer); // ?
+
+ DEBUG_PRINTLN(F("Enabling interrupt latch, clear on any read, AUX bypass enabled"));
+ I2Cdev::writeByte(devAddr, MPU6050_RA_INT_PIN_CFG, 0x32);
+
+ // enable MPU AUX I2C bypass mode
+ //DEBUG_PRINTLN(F("Enabling AUX I2C bypass mode..."));
+ //setI2CBypassEnabled(true);
+
+ DEBUG_PRINTLN(F("Setting magnetometer mode to power-down..."));
+ //mag -> setMode(0);
+ I2Cdev::writeByte(0x0E, 0x0A, 0x00);
+
+ DEBUG_PRINTLN(F("Setting magnetometer mode to fuse access..."));
+ //mag -> setMode(0x0F);
+ I2Cdev::writeByte(0x0E, 0x0A, 0x0F);
+
+ DEBUG_PRINTLN(F("Reading mag magnetometer factory calibration..."));
+ int8_t asax, asay, asaz;
+ //mag -> getAdjustment(&asax, &asay, &asaz);
+ I2Cdev::readBytes(0x0E, 0x10, 3, buffer);
+ asax = (int8_t)buffer[0];
+ asay = (int8_t)buffer[1];
+ asaz = (int8_t)buffer[2];
+ DEBUG_PRINT(F("Adjustment X/Y/Z = "));
+ DEBUG_PRINT(asax);
+ DEBUG_PRINT(F(" / "));
+ DEBUG_PRINT(asay);
+ DEBUG_PRINT(F(" / "));
+ DEBUG_PRINTLN(asaz);
+
+ DEBUG_PRINTLN(F("Setting magnetometer mode to power-down..."));
+ //mag -> setMode(0);
+ I2Cdev::writeByte(0x0E, 0x0A, 0x00);
+
+ // load DMP code into memory banks
+ DEBUG_PRINT(F("Writing DMP code to MPU memory banks ("));
+ DEBUG_PRINT(MPU6050_DMP_CODE_SIZE);
+ DEBUG_PRINTLN(F(" bytes)"));
+ if (writeProgMemoryBlock(dmpMemory, MPU6050_DMP_CODE_SIZE)) {
+ DEBUG_PRINTLN(F("Success! DMP code written and verified."));
+
+ DEBUG_PRINTLN(F("Configuring DMP and related settings..."));
+
+ // write DMP configuration
+ DEBUG_PRINT(F("Writing DMP configuration to MPU memory banks ("));
+ DEBUG_PRINT(MPU6050_DMP_CONFIG_SIZE);
+ DEBUG_PRINTLN(F(" bytes in config def)"));
+ if (writeProgDMPConfigurationSet(dmpConfig, MPU6050_DMP_CONFIG_SIZE)) {
+ DEBUG_PRINTLN(F("Success! DMP configuration written and verified."));
+
+ DEBUG_PRINTLN(F("Setting DMP and FIFO_OFLOW interrupts enabled..."));
+ setIntEnabled(1< setMode(1);
+ I2Cdev::writeByte(0x0E, 0x0A, 0x01);
+
+ // setup AK8975 (0x0E) as Slave 0 in read mode
+ DEBUG_PRINTLN(F("Setting up AK8975 read slave 0..."));
+ I2Cdev::writeByte(0x68, MPU6050_RA_I2C_SLV0_ADDR, 0x8E);
+ I2Cdev::writeByte(0x68, MPU6050_RA_I2C_SLV0_REG, 0x01);
+ I2Cdev::writeByte(0x68, MPU6050_RA_I2C_SLV0_CTRL, 0xDA);
+
+ // setup AK8975 (0x0E) as Slave 2 in write mode
+ DEBUG_PRINTLN(F("Setting up AK8975 write slave 2..."));
+ I2Cdev::writeByte(0x68, MPU6050_RA_I2C_SLV2_ADDR, 0x0E);
+ I2Cdev::writeByte(0x68, MPU6050_RA_I2C_SLV2_REG, 0x0A);
+ I2Cdev::writeByte(0x68, MPU6050_RA_I2C_SLV2_CTRL, 0x81);
+ I2Cdev::writeByte(0x68, MPU6050_RA_I2C_SLV2_DO, 0x01);
+
+ // setup I2C timing/delay control
+ DEBUG_PRINTLN(F("Setting up slave access delay..."));
+ I2Cdev::writeByte(0x68, MPU6050_RA_I2C_SLV4_CTRL, 0x18);
+ I2Cdev::writeByte(0x68, MPU6050_RA_I2C_MST_DELAY_CTRL, 0x05);
+
+ // enable interrupts
+ DEBUG_PRINTLN(F("Enabling default interrupt behavior/no bypass..."));
+ I2Cdev::writeByte(0x68, MPU6050_RA_INT_PIN_CFG, 0x00);
+
+ // enable I2C master mode and reset DMP/FIFO
+ DEBUG_PRINTLN(F("Enabling I2C master mode..."));
+ I2Cdev::writeByte(0x68, MPU6050_RA_USER_CTRL, 0x20);
+ DEBUG_PRINTLN(F("Resetting FIFO..."));
+ I2Cdev::writeByte(0x68, MPU6050_RA_USER_CTRL, 0x24);
+ DEBUG_PRINTLN(F("Rewriting I2C master mode enabled because...I don't know"));
+ I2Cdev::writeByte(0x68, MPU6050_RA_USER_CTRL, 0x20);
+ DEBUG_PRINTLN(F("Enabling and resetting DMP/FIFO..."));
+ I2Cdev::writeByte(0x68, MPU6050_RA_USER_CTRL, 0xE8);
+
+ DEBUG_PRINTLN(F("Writing final memory update 5/19 (function unknown)..."));
+ for (j = 0; j < 4 || j < dmpUpdate[2] + 3; j++, pos++) dmpUpdate[j] = pgm_read_byte(&dmpUpdates[pos]);
+ writeMemoryBlock(dmpUpdate + 3, dmpUpdate[2], dmpUpdate[0], dmpUpdate[1]);
+ DEBUG_PRINTLN(F("Writing final memory update 6/19 (function unknown)..."));
+ for (j = 0; j < 4 || j < dmpUpdate[2] + 3; j++, pos++) dmpUpdate[j] = pgm_read_byte(&dmpUpdates[pos]);
+ writeMemoryBlock(dmpUpdate + 3, dmpUpdate[2], dmpUpdate[0], dmpUpdate[1]);
+ DEBUG_PRINTLN(F("Writing final memory update 7/19 (function unknown)..."));
+ for (j = 0; j < 4 || j < dmpUpdate[2] + 3; j++, pos++) dmpUpdate[j] = pgm_read_byte(&dmpUpdates[pos]);
+ writeMemoryBlock(dmpUpdate + 3, dmpUpdate[2], dmpUpdate[0], dmpUpdate[1]);
+ DEBUG_PRINTLN(F("Writing final memory update 8/19 (function unknown)..."));
+ for (j = 0; j < 4 || j < dmpUpdate[2] + 3; j++, pos++) dmpUpdate[j] = pgm_read_byte(&dmpUpdates[pos]);
+ writeMemoryBlock(dmpUpdate + 3, dmpUpdate[2], dmpUpdate[0], dmpUpdate[1]);
+ DEBUG_PRINTLN(F("Writing final memory update 9/19 (function unknown)..."));
+ for (j = 0; j < 4 || j < dmpUpdate[2] + 3; j++, pos++) dmpUpdate[j] = pgm_read_byte(&dmpUpdates[pos]);
+ writeMemoryBlock(dmpUpdate + 3, dmpUpdate[2], dmpUpdate[0], dmpUpdate[1]);
+ DEBUG_PRINTLN(F("Writing final memory update 10/19 (function unknown)..."));
+ for (j = 0; j < 4 || j < dmpUpdate[2] + 3; j++, pos++) dmpUpdate[j] = pgm_read_byte(&dmpUpdates[pos]);
+ writeMemoryBlock(dmpUpdate + 3, dmpUpdate[2], dmpUpdate[0], dmpUpdate[1]);
+ DEBUG_PRINTLN(F("Writing final memory update 11/19 (function unknown)..."));
+ for (j = 0; j < 4 || j < dmpUpdate[2] + 3; j++, pos++) dmpUpdate[j] = pgm_read_byte(&dmpUpdates[pos]);
+ writeMemoryBlock(dmpUpdate + 3, dmpUpdate[2], dmpUpdate[0], dmpUpdate[1]);
+
+ DEBUG_PRINTLN(F("Reading final memory update 12/19 (function unknown)..."));
+ for (j = 0; j < 4 || j < dmpUpdate[2] + 3; j++, pos++) dmpUpdate[j] = pgm_read_byte(&dmpUpdates[pos]);
+ readMemoryBlock(dmpUpdate + 3, dmpUpdate[2], dmpUpdate[0], dmpUpdate[1]);
+ #ifdef DEBUG
+ DEBUG_PRINT(F("Read bytes: "));
+ for (j = 0; j < 4; j++) {
+ DEBUG_PRINTF(dmpUpdate[3 + j], HEX);
+ DEBUG_PRINT(" ");
+ }
+ DEBUG_PRINTLN("");
+ #endif
+
+ DEBUG_PRINTLN(F("Writing final memory update 13/19 (function unknown)..."));
+ for (j = 0; j < 4 || j < dmpUpdate[2] + 3; j++, pos++) dmpUpdate[j] = pgm_read_byte(&dmpUpdates[pos]);
+ writeMemoryBlock(dmpUpdate + 3, dmpUpdate[2], dmpUpdate[0], dmpUpdate[1]);
+ DEBUG_PRINTLN(F("Writing final memory update 14/19 (function unknown)..."));
+ for (j = 0; j < 4 || j < dmpUpdate[2] + 3; j++, pos++) dmpUpdate[j] = pgm_read_byte(&dmpUpdates[pos]);
+ writeMemoryBlock(dmpUpdate + 3, dmpUpdate[2], dmpUpdate[0], dmpUpdate[1]);
+ DEBUG_PRINTLN(F("Writing final memory update 15/19 (function unknown)..."));
+ for (j = 0; j < 4 || j < dmpUpdate[2] + 3; j++, pos++) dmpUpdate[j] = pgm_read_byte(&dmpUpdates[pos]);
+ writeMemoryBlock(dmpUpdate + 3, dmpUpdate[2], dmpUpdate[0], dmpUpdate[1]);
+ DEBUG_PRINTLN(F("Writing final memory update 16/19 (function unknown)..."));
+ for (j = 0; j < 4 || j < dmpUpdate[2] + 3; j++, pos++) dmpUpdate[j] = pgm_read_byte(&dmpUpdates[pos]);
+ writeMemoryBlock(dmpUpdate + 3, dmpUpdate[2], dmpUpdate[0], dmpUpdate[1]);
+ DEBUG_PRINTLN(F("Writing final memory update 17/19 (function unknown)..."));
+ for (j = 0; j < 4 || j < dmpUpdate[2] + 3; j++, pos++) dmpUpdate[j] = pgm_read_byte(&dmpUpdates[pos]);
+ writeMemoryBlock(dmpUpdate + 3, dmpUpdate[2], dmpUpdate[0], dmpUpdate[1]);
+
+ DEBUG_PRINTLN(F("Waiting for FIRO count >= 46..."));
+ while ((fifoCount = getFIFOCount()) < 46);
+ DEBUG_PRINTLN(F("Reading FIFO..."));
+ getFIFOBytes(fifoBuffer, min(fifoCount, 128)); // safeguard only 128 bytes
+ DEBUG_PRINTLN(F("Reading interrupt status..."));
+ getIntStatus();
+
+ DEBUG_PRINTLN(F("Writing final memory update 18/19 (function unknown)..."));
+ for (j = 0; j < 4 || j < dmpUpdate[2] + 3; j++, pos++) dmpUpdate[j] = pgm_read_byte(&dmpUpdates[pos]);
+ writeMemoryBlock(dmpUpdate + 3, dmpUpdate[2], dmpUpdate[0], dmpUpdate[1]);
+
+ DEBUG_PRINTLN(F("Waiting for FIRO count >= 48..."));
+ while ((fifoCount = getFIFOCount()) < 48);
+ DEBUG_PRINTLN(F("Reading FIFO..."));
+ getFIFOBytes(fifoBuffer, min(fifoCount, 128)); // safeguard only 128 bytes
+ DEBUG_PRINTLN(F("Reading interrupt status..."));
+ getIntStatus();
+ DEBUG_PRINTLN(F("Waiting for FIRO count >= 48..."));
+ while ((fifoCount = getFIFOCount()) < 48);
+ DEBUG_PRINTLN(F("Reading FIFO..."));
+ getFIFOBytes(fifoBuffer, min(fifoCount, 128)); // safeguard only 128 bytes
+ DEBUG_PRINTLN(F("Reading interrupt status..."));
+ getIntStatus();
+
+ DEBUG_PRINTLN(F("Writing final memory update 19/19 (function unknown)..."));
+ for (j = 0; j < 4 || j < dmpUpdate[2] + 3; j++, pos++) dmpUpdate[j] = pgm_read_byte(&dmpUpdates[pos]);
+ writeMemoryBlock(dmpUpdate + 3, dmpUpdate[2], dmpUpdate[0], dmpUpdate[1]);
+
+ DEBUG_PRINTLN(F("Disabling DMP (you turn it on later)..."));
+ setDMPEnabled(false);
+
+ DEBUG_PRINTLN(F("Setting up internal 48-byte (default) DMP packet buffer..."));
+ dmpPacketSize = 48;
+ /*if ((dmpPacketBuffer = (uint8_t *)malloc(42)) == 0) {
+ return 3; // TODO: proper error code for no memory
+ }*/
+
+ DEBUG_PRINTLN(F("Resetting FIFO and clearing INT status one last time..."));
+ resetFIFO();
+ getIntStatus();
+ } else {
+ DEBUG_PRINTLN(F("ERROR! DMP configuration verification failed."));
+ return 2; // configuration block loading failed
+ }
+ } else {
+ DEBUG_PRINTLN(F("ERROR! DMP code verification failed."));
+ return 1; // main binary block loading failed
+ }
+ return 0; // success
+}
+
+bool MPU6050::dmpPacketAvailable() {
+ return getFIFOCount() >= dmpGetFIFOPacketSize();
+}
+
+// uint8_t MPU6050::dmpSetFIFORate(uint8_t fifoRate);
+// uint8_t MPU6050::dmpGetFIFORate();
+// uint8_t MPU6050::dmpGetSampleStepSizeMS();
+// uint8_t MPU6050::dmpGetSampleFrequency();
+// int32_t MPU6050::dmpDecodeTemperature(int8_t tempReg);
+
+//uint8_t MPU6050::dmpRegisterFIFORateProcess(inv_obj_func func, int16_t priority);
+//uint8_t MPU6050::dmpUnregisterFIFORateProcess(inv_obj_func func);
+//uint8_t MPU6050::dmpRunFIFORateProcesses();
+
+// uint8_t MPU6050::dmpSendQuaternion(uint_fast16_t accuracy);
+// uint8_t MPU6050::dmpSendGyro(uint_fast16_t elements, uint_fast16_t accuracy);
+// uint8_t MPU6050::dmpSendAccel(uint_fast16_t elements, uint_fast16_t accuracy);
+// uint8_t MPU6050::dmpSendLinearAccel(uint_fast16_t elements, uint_fast16_t accuracy);
+// uint8_t MPU6050::dmpSendLinearAccelInWorld(uint_fast16_t elements, uint_fast16_t accuracy);
+// uint8_t MPU6050::dmpSendControlData(uint_fast16_t elements, uint_fast16_t accuracy);
+// uint8_t MPU6050::dmpSendSensorData(uint_fast16_t elements, uint_fast16_t accuracy);
+// uint8_t MPU6050::dmpSendExternalSensorData(uint_fast16_t elements, uint_fast16_t accuracy);
+// uint8_t MPU6050::dmpSendGravity(uint_fast16_t elements, uint_fast16_t accuracy);
+// uint8_t MPU6050::dmpSendPacketNumber(uint_fast16_t accuracy);
+// uint8_t MPU6050::dmpSendQuantizedAccel(uint_fast16_t elements, uint_fast16_t accuracy);
+// uint8_t MPU6050::dmpSendEIS(uint_fast16_t elements, uint_fast16_t accuracy);
+
+uint8_t MPU6050::dmpGetAccel(int32_t *data, const uint8_t* packet) {
+ // TODO: accommodate different arrangements of sent data (ONLY default supported now)
+ if (packet == 0) packet = dmpPacketBuffer;
+ data[0] = (((uint32_t)packet[34] << 24) | ((uint32_t)packet[35] << 16) | ((uint32_t)packet[36] << 8) | packet[37]);
+ data[1] = (((uint32_t)packet[38] << 24) | ((uint32_t)packet[39] << 16) | ((uint32_t)packet[40] << 8) | packet[41]);
+ data[2] = (((uint32_t)packet[42] << 24) | ((uint32_t)packet[43] << 16) | ((uint32_t)packet[44] << 8) | packet[45]);
+ return 0;
+}
+uint8_t MPU6050::dmpGetAccel(int16_t *data, const uint8_t* packet) {
+ // TODO: accommodate different arrangements of sent data (ONLY default supported now)
+ if (packet == 0) packet = dmpPacketBuffer;
+ data[0] = (packet[34] << 8) | packet[35];
+ data[1] = (packet[38] << 8) | packet[39];
+ data[2] = (packet[42] << 8) | packet[43];
+ return 0;
+}
+uint8_t MPU6050::dmpGetAccel(VectorInt16 *v, const uint8_t* packet) {
+ // TODO: accommodate different arrangements of sent data (ONLY default supported now)
+ if (packet == 0) packet = dmpPacketBuffer;
+ v -> x = (packet[34] << 8) | packet[35];
+ v -> y = (packet[38] << 8) | packet[39];
+ v -> z = (packet[42] << 8) | packet[43];
+ return 0;
+}
+uint8_t MPU6050::dmpGetQuaternion(int32_t *data, const uint8_t* packet) {
+ // TODO: accommodate different arrangements of sent data (ONLY default supported now)
+ if (packet == 0) packet = dmpPacketBuffer;
+ data[0] = (((uint32_t)packet[0] << 24) | ((uint32_t)packet[1] << 16) | ((uint32_t)packet[2] << 8) | packet[3]);
+ data[1] = (((uint32_t)packet[4] << 24) | ((uint32_t)packet[5] << 16) | ((uint32_t)packet[6] << 8) | packet[7]);
+ data[2] = (((uint32_t)packet[8] << 24) | ((uint32_t)packet[9] << 16) | ((uint32_t)packet[10] << 8) | packet[11]);
+ data[3] = (((uint32_t)packet[12] << 24) | ((uint32_t)packet[13] << 16) | ((uint32_t)packet[14] << 8) | packet[15]);
+ return 0;
+}
+uint8_t MPU6050::dmpGetQuaternion(int16_t *data, const uint8_t* packet) {
+ // TODO: accommodate different arrangements of sent data (ONLY default supported now)
+ if (packet == 0) packet = dmpPacketBuffer;
+ data[0] = ((packet[0] << 8) | packet[1]);
+ data[1] = ((packet[4] << 8) | packet[5]);
+ data[2] = ((packet[8] << 8) | packet[9]);
+ data[3] = ((packet[12] << 8) | packet[13]);
+ return 0;
+}
+uint8_t MPU6050::dmpGetQuaternion(Quaternion *q, const uint8_t* packet) {
+ // TODO: accommodate different arrangements of sent data (ONLY default supported now)
+ int16_t qI[4];
+ uint8_t status = dmpGetQuaternion(qI, packet);
+ if (status == 0) {
+ q -> w = (float)qI[0] / 16384.0f;
+ q -> x = (float)qI[1] / 16384.0f;
+ q -> y = (float)qI[2] / 16384.0f;
+ q -> z = (float)qI[3] / 16384.0f;
+ return 0;
+ }
+ return status; // int16 return value, indicates error if this line is reached
+}
+// uint8_t MPU6050::dmpGet6AxisQuaternion(long *data, const uint8_t* packet);
+// uint8_t MPU6050::dmpGetRelativeQuaternion(long *data, const uint8_t* packet);
+uint8_t MPU6050::dmpGetGyro(int32_t *data, const uint8_t* packet) {
+ // TODO: accommodate different arrangements of sent data (ONLY default supported now)
+ if (packet == 0) packet = dmpPacketBuffer;
+ data[0] = (((uint32_t)packet[16] << 24) | ((uint32_t)packet[17] << 16) | ((uint32_t)packet[18] << 8) | packet[19]);
+ data[1] = (((uint32_t)packet[20] << 24) | ((uint32_t)packet[21] << 16) | ((uint32_t)packet[22] << 8) | packet[23]);
+ data[2] = (((uint32_t)packet[24] << 24) | ((uint32_t)packet[25] << 16) | ((uint32_t)packet[26] << 8) | packet[27]);
+ return 0;
+}
+uint8_t MPU6050::dmpGetGyro(int16_t *data, const uint8_t* packet) {
+ // TODO: accommodate different arrangements of sent data (ONLY default supported now)
+ if (packet == 0) packet = dmpPacketBuffer;
+ data[0] = (packet[16] << 8) | packet[17];
+ data[1] = (packet[20] << 8) | packet[21];
+ data[2] = (packet[24] << 8) | packet[25];
+ return 0;
+}
+uint8_t MPU6050::dmpGetMag(int16_t *data, const uint8_t* packet) {
+ // TODO: accommodate different arrangements of sent data (ONLY default supported now)
+ if (packet == 0) packet = dmpPacketBuffer;
+ data[0] = (packet[28] << 8) | packet[29];
+ data[1] = (packet[30] << 8) | packet[31];
+ data[2] = (packet[32] << 8) | packet[33];
+ return 0;
+}
+// uint8_t MPU6050::dmpSetLinearAccelFilterCoefficient(float coef);
+// uint8_t MPU6050::dmpGetLinearAccel(long *data, const uint8_t* packet);
+uint8_t MPU6050::dmpGetLinearAccel(VectorInt16 *v, VectorInt16 *vRaw, VectorFloat *gravity) {
+ // get rid of the gravity component (+1g = +4096 in standard DMP FIFO packet)
+ v -> x = vRaw -> x - gravity -> x*4096;
+ v -> y = vRaw -> y - gravity -> y*4096;
+ v -> z = vRaw -> z - gravity -> z*4096;
+ return 0;
+}
+// uint8_t MPU6050::dmpGetLinearAccelInWorld(long *data, const uint8_t* packet);
+uint8_t MPU6050::dmpGetLinearAccelInWorld(VectorInt16 *v, VectorInt16 *vReal, Quaternion *q) {
+ // rotate measured 3D acceleration vector into original state
+ // frame of reference based on orientation quaternion
+ memcpy(v, vReal, sizeof(VectorInt16));
+ v -> rotate(q);
+ return 0;
+}
+// uint8_t MPU6050::dmpGetGyroAndAccelSensor(long *data, const uint8_t* packet);
+// uint8_t MPU6050::dmpGetGyroSensor(long *data, const uint8_t* packet);
+// uint8_t MPU6050::dmpGetControlData(long *data, const uint8_t* packet);
+// uint8_t MPU6050::dmpGetTemperature(long *data, const uint8_t* packet);
+// uint8_t MPU6050::dmpGetGravity(long *data, const uint8_t* packet);
+uint8_t MPU6050::dmpGetGravity(int16_t *data, const uint8_t* packet) {
+ /* +1g corresponds to +8192, sensitivity is 2g. */
+ int16_t qI[4];
+ uint8_t status = dmpGetQuaternion(qI, packet);
+ data[0] = ((int32_t)qI[1] * qI[3] - (int32_t)qI[0] * qI[2]) / 16384;
+ data[1] = ((int32_t)qI[0] * qI[1] + (int32_t)qI[2] * qI[3]) / 16384;
+ data[2] = ((int32_t)qI[0] * qI[0] - (int32_t)qI[1] * qI[1]
+ - (int32_t)qI[2] * qI[2] + (int32_t)qI[3] * qI[3]) / (2 * 16384);
+ return status;
+}
+
+uint8_t MPU6050::dmpGetGravity(VectorFloat *v, Quaternion *q) {
+ v -> x = 2 * (q -> x*q -> z - q -> w*q -> y);
+ v -> y = 2 * (q -> w*q -> x + q -> y*q -> z);
+ v -> z = q -> w*q -> w - q -> x*q -> x - q -> y*q -> y + q -> z*q -> z;
+ return 0;
+}
+// uint8_t MPU6050::dmpGetUnquantizedAccel(long *data, const uint8_t* packet);
+// uint8_t MPU6050::dmpGetQuantizedAccel(long *data, const uint8_t* packet);
+// uint8_t MPU6050::dmpGetExternalSensorData(long *data, int size, const uint8_t* packet);
+// uint8_t MPU6050::dmpGetEIS(long *data, const uint8_t* packet);
+
+uint8_t MPU6050::dmpGetEuler(float *data, Quaternion *q) {
+ data[0] = atan2(2*q -> x*q -> y - 2*q -> w*q -> z, 2*q -> w*q -> w + 2*q -> x*q -> x - 1); // psi
+ data[1] = -asin(2*q -> x*q -> z + 2*q -> w*q -> y); // theta
+ data[2] = atan2(2*q -> y*q -> z - 2*q -> w*q -> x, 2*q -> w*q -> w + 2*q -> z*q -> z - 1); // phi
+ return 0;
+}
+
+#ifdef USE_OLD_DMPGETYAWPITCHROLL
+uint8_t MPU6050::dmpGetYawPitchRoll(float *data, Quaternion *q, VectorFloat *gravity) {
+ // yaw: (about Z axis)
+ data[0] = atan2(2*q -> x*q -> y - 2*q -> w*q -> z, 2*q -> w*q -> w + 2*q -> x*q -> x - 1);
+ // pitch: (nose up/down, about Y axis)
+ data[1] = atan(gravity -> x / sqrt(gravity -> y*gravity -> y + gravity -> z*gravity -> z));
+ // roll: (tilt left/right, about X axis)
+ data[2] = atan(gravity -> y / sqrt(gravity -> x*gravity -> x + gravity -> z*gravity -> z));
+ return 0;
+}
+#else
+uint8_t MPU6050::dmpGetYawPitchRoll(float *data, Quaternion *q, VectorFloat *gravity) {
+ // yaw: (about Z axis)
+ data[0] = atan2(2*q -> x*q -> y - 2*q -> w*q -> z, 2*q -> w*q -> w + 2*q -> x*q -> x - 1);
+ // pitch: (nose up/down, about Y axis)
+ data[1] = atan2(gravity -> x , sqrt(gravity -> y*gravity -> y + gravity -> z*gravity -> z));
+ // roll: (tilt left/right, about X axis)
+ data[2] = atan2(gravity -> y , gravity -> z);
+ if(gravity->z<0) {
+ if(data[1]>0) {
+ data[1] = PI - data[1];
+ } else {
+ data[1] = -PI - data[1];
+ }
+ }
+ return 0;
+}
+#endif
+
+// uint8_t MPU6050::dmpGetAccelFloat(float *data, const uint8_t* packet);
+// uint8_t MPU6050::dmpGetQuaternionFloat(float *data, const uint8_t* packet);
+
+uint8_t MPU6050::dmpProcessFIFOPacket(const unsigned char *dmpData) {
+ /*for (uint8_t k = 0; k < dmpPacketSize; k++) {
+ if (dmpData[k] < 0x10) Serial.print("0");
+ Serial.print(dmpData[k], HEX);
+ Serial.print(" ");
+ }
+ Serial.print("\n");*/
+ //Serial.println((uint16_t)dmpPacketBuffer);
+ return 0;
+}
+uint8_t MPU6050::dmpReadAndProcessFIFOPacket(uint8_t numPackets, uint8_t *processed) {
+ uint8_t status;
+ uint8_t buf[dmpPacketSize];
+ for (uint8_t i = 0; i < numPackets; i++) {
+ // read packet from FIFO
+ getFIFOBytes(buf, dmpPacketSize);
+
+ // process packet
+ if ((status = dmpProcessFIFOPacket(buf)) > 0) return status;
+
+ // increment external process count variable, if supplied
+ if (processed != 0) *processed++;
+ }
+ return 0;
+}
+
+// uint8_t MPU6050::dmpSetFIFOProcessedCallback(void (*func) (void));
+
+// uint8_t MPU6050::dmpInitFIFOParam();
+// uint8_t MPU6050::dmpCloseFIFO();
+// uint8_t MPU6050::dmpSetGyroDataSource(uint_fast8_t source);
+// uint8_t MPU6050::dmpDecodeQuantizedAccel();
+// uint32_t MPU6050::dmpGetGyroSumOfSquare();
+// uint32_t MPU6050::dmpGetAccelSumOfSquare();
+// void MPU6050::dmpOverrideQuaternion(long *q);
+uint16_t MPU6050::dmpGetFIFOPacketSize() {
+ return dmpPacketSize;
+}
+
+#endif /* _MPU6050_9AXIS_MOTIONAPPS41_H_ */
diff --git a/Versions/dRehmFlight_ESP32_BETA_1.3/src/MPU6050/helper_3dmath.h b/Versions/dRehmFlight_ESP32_BETA_1.3/src/MPU6050/helper_3dmath.h
new file mode 100644
index 00000000..9ed260ec
--- /dev/null
+++ b/Versions/dRehmFlight_ESP32_BETA_1.3/src/MPU6050/helper_3dmath.h
@@ -0,0 +1,216 @@
+// I2C device class (I2Cdev) demonstration Arduino sketch for MPU6050 class, 3D math helper
+// 6/5/2012 by Jeff Rowberg
+// Updates should (hopefully) always be available at https://github.com/jrowberg/i2cdevlib
+//
+// Changelog:
+// 2012-06-05 - add 3D math helper file to DMP6 example sketch
+
+/* ============================================
+I2Cdev device library code is placed under the MIT license
+Copyright (c) 2012 Jeff Rowberg
+
+Permission is hereby granted, free of charge, to any person obtaining a copy
+of this software and associated documentation files (the "Software"), to deal
+in the Software without restriction, including without limitation the rights
+to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+copies of the Software, and to permit persons to whom the Software is
+furnished to do so, subject to the following conditions:
+
+The above copyright notice and this permission notice shall be included in
+all copies or substantial portions of the Software.
+
+THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+THE SOFTWARE.
+===============================================
+*/
+
+#ifndef _HELPER_3DMATH_H_
+#define _HELPER_3DMATH_H_
+
+class Quaternion {
+ public:
+ float w;
+ float x;
+ float y;
+ float z;
+
+ Quaternion() {
+ w = 1.0f;
+ x = 0.0f;
+ y = 0.0f;
+ z = 0.0f;
+ }
+
+ Quaternion(float nw, float nx, float ny, float nz) {
+ w = nw;
+ x = nx;
+ y = ny;
+ z = nz;
+ }
+
+ Quaternion getProduct(Quaternion q) {
+ // Quaternion multiplication is defined by:
+ // (Q1 * Q2).w = (w1w2 - x1x2 - y1y2 - z1z2)
+ // (Q1 * Q2).x = (w1x2 + x1w2 + y1z2 - z1y2)
+ // (Q1 * Q2).y = (w1y2 - x1z2 + y1w2 + z1x2)
+ // (Q1 * Q2).z = (w1z2 + x1y2 - y1x2 + z1w2
+ return Quaternion(
+ w*q.w - x*q.x - y*q.y - z*q.z, // new w
+ w*q.x + x*q.w + y*q.z - z*q.y, // new x
+ w*q.y - x*q.z + y*q.w + z*q.x, // new y
+ w*q.z + x*q.y - y*q.x + z*q.w); // new z
+ }
+
+ Quaternion getConjugate() {
+ return Quaternion(w, -x, -y, -z);
+ }
+
+ float getMagnitude() {
+ return sqrt(w*w + x*x + y*y + z*z);
+ }
+
+ void normalize() {
+ float m = getMagnitude();
+ w /= m;
+ x /= m;
+ y /= m;
+ z /= m;
+ }
+
+ Quaternion getNormalized() {
+ Quaternion r(w, x, y, z);
+ r.normalize();
+ return r;
+ }
+};
+
+class VectorInt16 {
+ public:
+ int16_t x;
+ int16_t y;
+ int16_t z;
+
+ VectorInt16() {
+ x = 0;
+ y = 0;
+ z = 0;
+ }
+
+ VectorInt16(int16_t nx, int16_t ny, int16_t nz) {
+ x = nx;
+ y = ny;
+ z = nz;
+ }
+
+ float getMagnitude() {
+ return sqrt(x*x + y*y + z*z);
+ }
+
+ void normalize() {
+ float m = getMagnitude();
+ x /= m;
+ y /= m;
+ z /= m;
+ }
+
+ VectorInt16 getNormalized() {
+ VectorInt16 r(x, y, z);
+ r.normalize();
+ return r;
+ }
+
+ void rotate(Quaternion *q) {
+ // http://www.cprogramming.com/tutorial/3d/quaternions.html
+ // http://www.euclideanspace.com/maths/algebra/realNormedAlgebra/quaternions/transforms/index.htm
+ // http://content.gpwiki.org/index.php/OpenGL:Tutorials:Using_Quaternions_to_represent_rotation
+ // ^ or: http://webcache.googleusercontent.com/search?q=cache:xgJAp3bDNhQJ:content.gpwiki.org/index.php/OpenGL:Tutorials:Using_Quaternions_to_represent_rotation&hl=en&gl=us&strip=1
+
+ // P_out = q * P_in * conj(q)
+ // - P_out is the output vector
+ // - q is the orientation quaternion
+ // - P_in is the input vector (a*aReal)
+ // - conj(q) is the conjugate of the orientation quaternion (q=[w,x,y,z], q*=[w,-x,-y,-z])
+ Quaternion p(0, x, y, z);
+
+ // quaternion multiplication: q * p, stored back in p
+ p = q -> getProduct(p);
+
+ // quaternion multiplication: p * conj(q), stored back in p
+ p = p.getProduct(q -> getConjugate());
+
+ // p quaternion is now [0, x', y', z']
+ x = p.x;
+ y = p.y;
+ z = p.z;
+ }
+
+ VectorInt16 getRotated(Quaternion *q) {
+ VectorInt16 r(x, y, z);
+ r.rotate(q);
+ return r;
+ }
+};
+
+class VectorFloat {
+ public:
+ float x;
+ float y;
+ float z;
+
+ VectorFloat() {
+ x = 0;
+ y = 0;
+ z = 0;
+ }
+
+ VectorFloat(float nx, float ny, float nz) {
+ x = nx;
+ y = ny;
+ z = nz;
+ }
+
+ float getMagnitude() {
+ return sqrt(x*x + y*y + z*z);
+ }
+
+ void normalize() {
+ float m = getMagnitude();
+ x /= m;
+ y /= m;
+ z /= m;
+ }
+
+ VectorFloat getNormalized() {
+ VectorFloat r(x, y, z);
+ r.normalize();
+ return r;
+ }
+
+ void rotate(Quaternion *q) {
+ Quaternion p(0, x, y, z);
+
+ // quaternion multiplication: q * p, stored back in p
+ p = q -> getProduct(p);
+
+ // quaternion multiplication: p * conj(q), stored back in p
+ p = p.getProduct(q -> getConjugate());
+
+ // p quaternion is now [0, x', y', z']
+ x = p.x;
+ y = p.y;
+ z = p.z;
+ }
+
+ VectorFloat getRotated(Quaternion *q) {
+ VectorFloat r(x, y, z);
+ r.rotate(q);
+ return r;
+ }
+};
+
+#endif /* _HELPER_3DMATH_H_ */
\ No newline at end of file
diff --git a/Versions/dRehmFlight_ESP32_BETA_1.3/src/MPU9250/MPU9250.cpp b/Versions/dRehmFlight_ESP32_BETA_1.3/src/MPU9250/MPU9250.cpp
new file mode 100644
index 00000000..7d2722a8
--- /dev/null
+++ b/Versions/dRehmFlight_ESP32_BETA_1.3/src/MPU9250/MPU9250.cpp
@@ -0,0 +1,1202 @@
+/*
+MPU9250.cpp
+Brian R Taylor
[email protected]
+Copyright (c) 2017 Bolder Flight Systems
+Permission is hereby granted, free of charge, to any person obtaining a copy of this software
+and associated documentation files (the "Software"), to deal in the Software without restriction,
+including without limitation the rights to use, copy, modify, merge, publish, distribute,
+sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is
+furnished to do so, subject to the following conditions:
+The above copyright notice and this permission notice shall be included in all copies or
+substantial portions of the Software.
+THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING
+BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM,
+DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
+*/
+
+#include "Arduino.h"
+#include "MPU9250.h"
+
+/* MPU9250 object, input the I2C bus and address */
+MPU9250::MPU9250(TwoWire &bus,uint8_t address){
+ _i2c = &bus; // I2C bus
+ _address = address; // I2C address
+ _useSPI = false; // set to use I2C
+}
+
+/* MPU9250 object, input the SPI bus and chip select pin */
+MPU9250::MPU9250(SPIClass &bus,uint8_t csPin){
+ _spi = &bus; // SPI bus
+ _csPin = csPin; // chip select pin
+ _useSPI = true; // set to use SPI
+}
+
+/* starts communication with the MPU-9250 */
+int MPU9250::begin(){
+ if( _useSPI ) { // using SPI for communication
+ // use low speed SPI for register setting
+ _useSPIHS = false;
+ // setting CS pin to output
+ pinMode(_csPin,OUTPUT);
+ // setting CS pin high
+ digitalWrite(_csPin,HIGH);
+ // begin SPI communication
+ _spi->begin();
+ } else { // using I2C for communication
+ // starting the I2C bus
+ _i2c->begin();
+ // setting the I2C clock
+ _i2c->setClock(_i2cRate);
+ }
+ // select clock source to gyro
+ if(writeRegister(PWR_MGMNT_1,CLOCK_SEL_PLL) < 0){
+ return -1;
+ }
+ // enable I2C master mode
+ if(writeRegister(USER_CTRL,I2C_MST_EN) < 0){
+ return -2;
+ }
+ // set the I2C bus speed to 400 kHz
+ if(writeRegister(I2C_MST_CTRL,I2C_MST_CLK) < 0){
+ return -3;
+ }
+ // set AK8963 to Power Down
+ writeAK8963Register(AK8963_CNTL1,AK8963_PWR_DOWN);
+ // reset the MPU9250
+ writeRegister(PWR_MGMNT_1,PWR_RESET);
+ // wait for MPU-9250 to come back up
+ delay(1);
+ // reset the AK8963
+ writeAK8963Register(AK8963_CNTL2,AK8963_RESET);
+ // select clock source to gyro
+ if(writeRegister(PWR_MGMNT_1,CLOCK_SEL_PLL) < 0){
+ return -4;
+ }
+ // check the WHO AM I byte, expected value is 0x71 (decimal 113) or 0x73 (decimal 115)
+ if((whoAmI() != 113)&&(whoAmI() != 115)){
+ return -5;
+ }
+ // enable accelerometer and gyro
+ if(writeRegister(PWR_MGMNT_2,SEN_ENABLE) < 0){
+ return -6;
+ }
+ // setting accel range to 16G as default
+ if(writeRegister(ACCEL_CONFIG,ACCEL_FS_SEL_16G) < 0){
+ return -7;
+ }
+ _accelScale = G * 16.0f/32767.5f; // setting the accel scale to 16G
+ _accelRange = ACCEL_RANGE_16G;
+ // setting the gyro range to 2000DPS as default
+ if(writeRegister(GYRO_CONFIG,GYRO_FS_SEL_2000DPS) < 0){
+ return -8;
+ }
+ _gyroScale = 2000.0f/32767.5f * _d2r; // setting the gyro scale to 2000DPS
+ _gyroRange = GYRO_RANGE_2000DPS;
+ // setting bandwidth to 184Hz as default
+ if(writeRegister(ACCEL_CONFIG2,ACCEL_DLPF_184) < 0){
+ return -9;
+ }
+ if(writeRegister(CONFIG,GYRO_DLPF_184) < 0){ // setting gyro bandwidth to 184Hz
+ return -10;
+ }
+ _bandwidth = DLPF_BANDWIDTH_184HZ;
+ // setting the sample rate divider to 0 as default
+ if(writeRegister(SMPDIV,0x00) < 0){
+ return -11;
+ }
+ _srd = 0;
+ // enable I2C master mode
+ if(writeRegister(USER_CTRL,I2C_MST_EN) < 0){
+ return -12;
+ }
+ // set the I2C bus speed to 400 kHz
+ if( writeRegister(I2C_MST_CTRL,I2C_MST_CLK) < 0){
+ return -13;
+ }
+ // check AK8963 WHO AM I register, expected value is 0x48 (decimal 72)
+ if( whoAmIAK8963() != 72 ){
+ return -14;
+ }
+ /* get the magnetometer calibration */
+ // set AK8963 to Power Down
+ if(writeAK8963Register(AK8963_CNTL1,AK8963_PWR_DOWN) < 0){
+ return -15;
+ }
+ delay(100); // long wait between AK8963 mode changes
+ // set AK8963 to FUSE ROM access
+ if(writeAK8963Register(AK8963_CNTL1,AK8963_FUSE_ROM) < 0){
+ return -16;
+ }
+ delay(100); // long wait between AK8963 mode changes
+ // read the AK8963 ASA registers and compute magnetometer scale factors
+ readAK8963Registers(AK8963_ASA,3,_buffer);
+ _magScaleX = ((((float)_buffer[0]) - 128.0f)/(256.0f) + 1.0f) * 4912.0f / 32760.0f; // micro Tesla
+ _magScaleY = ((((float)_buffer[1]) - 128.0f)/(256.0f) + 1.0f) * 4912.0f / 32760.0f; // micro Tesla
+ _magScaleZ = ((((float)_buffer[2]) - 128.0f)/(256.0f) + 1.0f) * 4912.0f / 32760.0f; // micro Tesla
+ // set AK8963 to Power Down
+ if(writeAK8963Register(AK8963_CNTL1,AK8963_PWR_DOWN) < 0){
+ return -17;
+ }
+ delay(100); // long wait between AK8963 mode changes
+ // set AK8963 to 16 bit resolution, 100 Hz update rate
+ if(writeAK8963Register(AK8963_CNTL1,AK8963_CNT_MEAS2) < 0){
+ return -18;
+ }
+ delay(100); // long wait between AK8963 mode changes
+ // select clock source to gyro
+ if(writeRegister(PWR_MGMNT_1,CLOCK_SEL_PLL) < 0){
+ return -19;
+ }
+ // instruct the MPU9250 to get 7 bytes of data from the AK8963 at the sample rate
+ readAK8963Registers(AK8963_HXL,7,_buffer);
+ // estimate gyro bias
+ if (calibrateGyro() < 0) {
+ return -20;
+ }
+ // successful init, return 1
+ return 1;
+}
+
+/* sets the accelerometer full scale range to values other than default */
+int MPU9250::setAccelRange(AccelRange range) {
+ // use low speed SPI for register setting
+ _useSPIHS = false;
+ switch(range) {
+ case ACCEL_RANGE_2G: {
+ // setting the accel range to 2G
+ if(writeRegister(ACCEL_CONFIG,ACCEL_FS_SEL_2G) < 0){
+ return -1;
+ }
+ _accelScale = G * 2.0f/32767.5f; // setting the accel scale to 2G
+ break;
+ }
+ case ACCEL_RANGE_4G: {
+ // setting the accel range to 4G
+ if(writeRegister(ACCEL_CONFIG,ACCEL_FS_SEL_4G) < 0){
+ return -1;
+ }
+ _accelScale = G * 4.0f/32767.5f; // setting the accel scale to 4G
+ break;
+ }
+ case ACCEL_RANGE_8G: {
+ // setting the accel range to 8G
+ if(writeRegister(ACCEL_CONFIG,ACCEL_FS_SEL_8G) < 0){
+ return -1;
+ }
+ _accelScale = G * 8.0f/32767.5f; // setting the accel scale to 8G
+ break;
+ }
+ case ACCEL_RANGE_16G: {
+ // setting the accel range to 16G
+ if(writeRegister(ACCEL_CONFIG,ACCEL_FS_SEL_16G) < 0){
+ return -1;
+ }
+ _accelScale = G * 16.0f/32767.5f; // setting the accel scale to 16G
+ break;
+ }
+ }
+ _accelRange = range;
+ return 1;
+}
+
+/* sets the gyro full scale range to values other than default */
+int MPU9250::setGyroRange(GyroRange range) {
+ // use low speed SPI for register setting
+ _useSPIHS = false;
+ switch(range) {
+ case GYRO_RANGE_250DPS: {
+ // setting the gyro range to 250DPS
+ if(writeRegister(GYRO_CONFIG,GYRO_FS_SEL_250DPS) < 0){
+ return -1;
+ }
+ _gyroScale = 250.0f/32767.5f * _d2r; // setting the gyro scale to 250DPS
+ break;
+ }
+ case GYRO_RANGE_500DPS: {
+ // setting the gyro range to 500DPS
+ if(writeRegister(GYRO_CONFIG,GYRO_FS_SEL_500DPS) < 0){
+ return -1;
+ }
+ _gyroScale = 500.0f/32767.5f * _d2r; // setting the gyro scale to 500DPS
+ break;
+ }
+ case GYRO_RANGE_1000DPS: {
+ // setting the gyro range to 1000DPS
+ if(writeRegister(GYRO_CONFIG,GYRO_FS_SEL_1000DPS) < 0){
+ return -1;
+ }
+ _gyroScale = 1000.0f/32767.5f * _d2r; // setting the gyro scale to 1000DPS
+ break;
+ }
+ case GYRO_RANGE_2000DPS: {
+ // setting the gyro range to 2000DPS
+ if(writeRegister(GYRO_CONFIG,GYRO_FS_SEL_2000DPS) < 0){
+ return -1;
+ }
+ _gyroScale = 2000.0f/32767.5f * _d2r; // setting the gyro scale to 2000DPS
+ break;
+ }
+ }
+ _gyroRange = range;
+ return 1;
+}
+
+/* sets the DLPF bandwidth to values other than default */
+int MPU9250::setDlpfBandwidth(DlpfBandwidth bandwidth) {
+ // use low speed SPI for register setting
+ _useSPIHS = false;
+ switch(bandwidth) {
+ case DLPF_BANDWIDTH_184HZ: {
+ if(writeRegister(ACCEL_CONFIG2,ACCEL_DLPF_184) < 0){ // setting accel bandwidth to 184Hz
+ return -1;
+ }
+ if(writeRegister(CONFIG,GYRO_DLPF_184) < 0){ // setting gyro bandwidth to 184Hz
+ return -2;
+ }
+ break;
+ }
+ case DLPF_BANDWIDTH_92HZ: {
+ if(writeRegister(ACCEL_CONFIG2,ACCEL_DLPF_92) < 0){ // setting accel bandwidth to 92Hz
+ return -1;
+ }
+ if(writeRegister(CONFIG,GYRO_DLPF_92) < 0){ // setting gyro bandwidth to 92Hz
+ return -2;
+ }
+ break;
+ }
+ case DLPF_BANDWIDTH_41HZ: {
+ if(writeRegister(ACCEL_CONFIG2,ACCEL_DLPF_41) < 0){ // setting accel bandwidth to 41Hz
+ return -1;
+ }
+ if(writeRegister(CONFIG,GYRO_DLPF_41) < 0){ // setting gyro bandwidth to 41Hz
+ return -2;
+ }
+ break;
+ }
+ case DLPF_BANDWIDTH_20HZ: {
+ if(writeRegister(ACCEL_CONFIG2,ACCEL_DLPF_20) < 0){ // setting accel bandwidth to 20Hz
+ return -1;
+ }
+ if(writeRegister(CONFIG,GYRO_DLPF_20) < 0){ // setting gyro bandwidth to 20Hz
+ return -2;
+ }
+ break;
+ }
+ case DLPF_BANDWIDTH_10HZ: {
+ if(writeRegister(ACCEL_CONFIG2,ACCEL_DLPF_10) < 0){ // setting accel bandwidth to 10Hz
+ return -1;
+ }
+ if(writeRegister(CONFIG,GYRO_DLPF_10) < 0){ // setting gyro bandwidth to 10Hz
+ return -2;
+ }
+ break;
+ }
+ case DLPF_BANDWIDTH_5HZ: {
+ if(writeRegister(ACCEL_CONFIG2,ACCEL_DLPF_5) < 0){ // setting accel bandwidth to 5Hz
+ return -1;
+ }
+ if(writeRegister(CONFIG,GYRO_DLPF_5) < 0){ // setting gyro bandwidth to 5Hz
+ return -2;
+ }
+ break;
+ }
+ }
+ _bandwidth = bandwidth;
+ return 1;
+}
+
+/* sets the sample rate divider to values other than default */
+int MPU9250::setSrd(uint8_t srd) {
+ // use low speed SPI for register setting
+ _useSPIHS = false;
+ /* setting the sample rate divider to 19 to facilitate setting up magnetometer */
+ if(writeRegister(SMPDIV,19) < 0){ // setting the sample rate divider
+ return -1;
+ }
+ if(srd > 9){
+ // set AK8963 to Power Down
+ if(writeAK8963Register(AK8963_CNTL1,AK8963_PWR_DOWN) < 0){
+ return -2;
+ }
+ delay(100); // long wait between AK8963 mode changes
+ // set AK8963 to 16 bit resolution, 8 Hz update rate
+ if(writeAK8963Register(AK8963_CNTL1,AK8963_CNT_MEAS1) < 0){
+ return -3;
+ }
+ delay(100); // long wait between AK8963 mode changes
+ // instruct the MPU9250 to get 7 bytes of data from the AK8963 at the sample rate
+ readAK8963Registers(AK8963_HXL,7,_buffer);
+ } else {
+ // set AK8963 to Power Down
+ if(writeAK8963Register(AK8963_CNTL1,AK8963_PWR_DOWN) < 0){
+ return -2;
+ }
+ delay(100); // long wait between AK8963 mode changes
+ // set AK8963 to 16 bit resolution, 100 Hz update rate
+ if(writeAK8963Register(AK8963_CNTL1,AK8963_CNT_MEAS2) < 0){
+ return -3;
+ }
+ delay(100); // long wait between AK8963 mode changes
+ // instruct the MPU9250 to get 7 bytes of data from the AK8963 at the sample rate
+ readAK8963Registers(AK8963_HXL,7,_buffer);
+ }
+ /* setting the sample rate divider */
+ if(writeRegister(SMPDIV,srd) < 0){ // setting the sample rate divider
+ return -4;
+ }
+ _srd = srd;
+ return 1;
+}
+
+/* enables the data ready interrupt */
+int MPU9250::enableDataReadyInterrupt() {
+ // use low speed SPI for register setting
+ _useSPIHS = false;
+ /* setting the interrupt */
+ if (writeRegister(INT_PIN_CFG,INT_PULSE_50US) < 0){ // setup interrupt, 50 us pulse
+ return -1;
+ }
+ if (writeRegister(INT_ENABLE,INT_RAW_RDY_EN) < 0){ // set to data ready
+ return -2;
+ }
+ return 1;
+}
+
+/* disables the data ready interrupt */
+int MPU9250::disableDataReadyInterrupt() {
+ // use low speed SPI for register setting
+ _useSPIHS = false;
+ if(writeRegister(INT_ENABLE,INT_DISABLE) < 0){ // disable interrupt
+ return -1;
+ }
+ return 1;
+}
+
+/* configures and enables wake on motion, low power mode */
+int MPU9250::enableWakeOnMotion(float womThresh_mg,LpAccelOdr odr) {
+ // use low speed SPI for register setting
+ _useSPIHS = false;
+ // set AK8963 to Power Down
+ writeAK8963Register(AK8963_CNTL1,AK8963_PWR_DOWN);
+ // reset the MPU9250
+ writeRegister(PWR_MGMNT_1,PWR_RESET);
+ // wait for MPU-9250 to come back up
+ delay(1);
+ if(writeRegister(PWR_MGMNT_1,0x00) < 0){ // cycle 0, sleep 0, standby 0
+ return -1;
+ }
+ if(writeRegister(PWR_MGMNT_2,DIS_GYRO) < 0){ // disable gyro measurements
+ return -2;
+ }
+ if(writeRegister(ACCEL_CONFIG2,ACCEL_DLPF_184) < 0){ // setting accel bandwidth to 184Hz
+ return -3;
+ }
+ if(writeRegister(INT_ENABLE,INT_WOM_EN) < 0){ // enabling interrupt to wake on motion
+ return -4;
+ }
+ if(writeRegister(MOT_DETECT_CTRL,(ACCEL_INTEL_EN | ACCEL_INTEL_MODE)) < 0){ // enabling accel hardware intelligence
+ return -5;
+ }
+ _womThreshold = map(womThresh_mg, 0, 1020, 0, 255);
+ if(writeRegister(WOM_THR,_womThreshold) < 0){ // setting wake on motion threshold
+ return -6;
+ }
+ if(writeRegister(LP_ACCEL_ODR,(uint8_t)odr) < 0){ // set frequency of wakeup
+ return -7;
+ }
+ if(writeRegister(PWR_MGMNT_1,PWR_CYCLE) < 0){ // switch to accel low power mode
+ return -8;
+ }
+ return 1;
+}
+
+/* configures and enables the FIFO buffer */
+int MPU9250FIFO::enableFifo(bool accel,bool gyro,bool mag,bool temp) {
+ // use low speed SPI for register setting
+ _useSPIHS = false;
+ if(writeRegister(USER_CTRL, (0x40 | I2C_MST_EN)) < 0){
+ return -1;
+ }
+ if(writeRegister(FIFO_EN,(accel*FIFO_ACCEL)|(gyro*FIFO_GYRO)|(mag*FIFO_MAG)|(temp*FIFO_TEMP)) < 0){
+ return -2;
+ }
+ _enFifoAccel = accel;
+ _enFifoGyro = gyro;
+ _enFifoMag = mag;
+ _enFifoTemp = temp;
+ _fifoFrameSize = accel*6 + gyro*6 + mag*7 + temp*2;
+ return 1;
+}
+
+/* reads the most current data from MPU9250 and stores in buffer */
+int MPU9250::readSensor() {
+ _useSPIHS = true; // use the high speed SPI for data readout
+ // grab the data from the MPU9250
+ if (readRegisters(ACCEL_OUT, 21, _buffer) < 0) {
+ return -1;
+ }
+ // combine into 16 bit values
+ _axcounts = (((int16_t)_buffer[0]) << 8) | _buffer[1];
+ _aycounts = (((int16_t)_buffer[2]) << 8) | _buffer[3];
+ _azcounts = (((int16_t)_buffer[4]) << 8) | _buffer[5];
+ _tcounts = (((int16_t)_buffer[6]) << 8) | _buffer[7];
+ _gxcounts = (((int16_t)_buffer[8]) << 8) | _buffer[9];
+ _gycounts = (((int16_t)_buffer[10]) << 8) | _buffer[11];
+ _gzcounts = (((int16_t)_buffer[12]) << 8) | _buffer[13];
+ _hxcounts = (((int16_t)_buffer[15]) << 8) | _buffer[14];
+ _hycounts = (((int16_t)_buffer[17]) << 8) | _buffer[16];
+ _hzcounts = (((int16_t)_buffer[19]) << 8) | _buffer[18];
+ // transform and convert to float values
+ _ax = (((float)(tX[0]*_axcounts + tX[1]*_aycounts + tX[2]*_azcounts) * _accelScale) - _axb)*_axs;
+ _ay = (((float)(tY[0]*_axcounts + tY[1]*_aycounts + tY[2]*_azcounts) * _accelScale) - _ayb)*_ays;
+ _az = (((float)(tZ[0]*_axcounts + tZ[1]*_aycounts + tZ[2]*_azcounts) * _accelScale) - _azb)*_azs;
+ _gx = ((float)(tX[0]*_gxcounts + tX[1]*_gycounts + tX[2]*_gzcounts) * _gyroScale) - _gxb;
+ _gy = ((float)(tY[0]*_gxcounts + tY[1]*_gycounts + tY[2]*_gzcounts) * _gyroScale) - _gyb;
+ _gz = ((float)(tZ[0]*_gxcounts + tZ[1]*_gycounts + tZ[2]*_gzcounts) * _gyroScale) - _gzb;
+ _hx = (((float)(_hxcounts) * _magScaleX) - _hxb)*_hxs;
+ _hy = (((float)(_hycounts) * _magScaleY) - _hyb)*_hys;
+ _hz = (((float)(_hzcounts) * _magScaleZ) - _hzb)*_hzs;
+ _t = ((((float) _tcounts) - _tempOffset)/_tempScale) + _tempOffset;
+ return 1;
+}
+
+/* returns the accelerometer measurement in the x direction, m/s/s */
+float MPU9250::getAccelX_mss() {
+ return _ax;
+}
+
+/* returns the accelerometer measurement in the y direction, m/s/s */
+float MPU9250::getAccelY_mss() {
+ return _ay;
+}
+
+/* returns the accelerometer measurement in the z direction, m/s/s */
+float MPU9250::getAccelZ_mss() {
+ return _az;
+}
+
+/* returns the gyroscope measurement in the x direction, rad/s */
+float MPU9250::getGyroX_rads() {
+ return _gx;
+}
+
+/* returns the gyroscope measurement in the y direction, rad/s */
+float MPU9250::getGyroY_rads() {
+ return _gy;
+}
+
+/* returns the gyroscope measurement in the z direction, rad/s */
+float MPU9250::getGyroZ_rads() {
+ return _gz;
+}
+
+/* returns the magnetometer measurement in the x direction, uT */
+float MPU9250::getMagX_uT() {
+ return _hx;
+}
+
+/* returns the magnetometer measurement in the y direction, uT */
+float MPU9250::getMagY_uT() {
+ return _hy;
+}
+
+/* returns the magnetometer measurement in the z direction, uT */
+float MPU9250::getMagZ_uT() {
+ return _hz;
+}
+
+/* returns the die temperature, C */
+float MPU9250::getTemperature_C() {
+ return _t;
+}
+
+/* reads data from the MPU9250 FIFO and stores in buffer */
+int MPU9250FIFO::readFifo() {
+ _useSPIHS = true; // use the high speed SPI for data readout
+ // get the fifo size
+ readRegisters(FIFO_COUNT, 2, _buffer);
+ _fifoSize = (((uint16_t) (_buffer[0]&0x0F)) <<8) + (((uint16_t) _buffer[1]));
+ // read and parse the buffer
+ for (size_t i=0; i < _fifoSize/_fifoFrameSize; i++) {
+ // grab the data from the MPU9250
+ if (readRegisters(FIFO_READ,_fifoFrameSize,_buffer) < 0) {
+ return -1;
+ }
+ if (_enFifoAccel) {
+ // combine into 16 bit values
+ _axcounts = (((int16_t)_buffer[0]) << 8) | _buffer[1];
+ _aycounts = (((int16_t)_buffer[2]) << 8) | _buffer[3];
+ _azcounts = (((int16_t)_buffer[4]) << 8) | _buffer[5];
+ // transform and convert to float values
+ _axFifo[i] = (((float)(tX[0]*_axcounts + tX[1]*_aycounts + tX[2]*_azcounts) * _accelScale)-_axb)*_axs;
+ _ayFifo[i] = (((float)(tY[0]*_axcounts + tY[1]*_aycounts + tY[2]*_azcounts) * _accelScale)-_ayb)*_ays;
+ _azFifo[i] = (((float)(tZ[0]*_axcounts + tZ[1]*_aycounts + tZ[2]*_azcounts) * _accelScale)-_azb)*_azs;
+ _aSize = _fifoSize/_fifoFrameSize;
+ }
+ if (_enFifoTemp) {
+ // combine into 16 bit values
+ _tcounts = (((int16_t)_buffer[0 + _enFifoAccel*6]) << 8) | _buffer[1 + _enFifoAccel*6];
+ // transform and convert to float values
+ _tFifo[i] = ((((float) _tcounts) - _tempOffset)/_tempScale) + _tempOffset;
+ _tSize = _fifoSize/_fifoFrameSize;
+ }
+ if (_enFifoGyro) {
+ // combine into 16 bit values
+ _gxcounts = (((int16_t)_buffer[0 + _enFifoAccel*6 + _enFifoTemp*2]) << 8) | _buffer[1 + _enFifoAccel*6 + _enFifoTemp*2];
+ _gycounts = (((int16_t)_buffer[2 + _enFifoAccel*6 + _enFifoTemp*2]) << 8) | _buffer[3 + _enFifoAccel*6 + _enFifoTemp*2];
+ _gzcounts = (((int16_t)_buffer[4 + _enFifoAccel*6 + _enFifoTemp*2]) << 8) | _buffer[5 + _enFifoAccel*6 + _enFifoTemp*2];
+ // transform and convert to float values
+ _gxFifo[i] = ((float)(tX[0]*_gxcounts + tX[1]*_gycounts + tX[2]*_gzcounts) * _gyroScale) - _gxb;
+ _gyFifo[i] = ((float)(tY[0]*_gxcounts + tY[1]*_gycounts + tY[2]*_gzcounts) * _gyroScale) - _gyb;
+ _gzFifo[i] = ((float)(tZ[0]*_gxcounts + tZ[1]*_gycounts + tZ[2]*_gzcounts) * _gyroScale) - _gzb;
+ _gSize = _fifoSize/_fifoFrameSize;
+ }
+ if (_enFifoMag) {
+ // combine into 16 bit values
+ _hxcounts = (((int16_t)_buffer[1 + _enFifoAccel*6 + _enFifoTemp*2 + _enFifoGyro*6]) << 8) | _buffer[0 + _enFifoAccel*6 + _enFifoTemp*2 + _enFifoGyro*6];
+ _hycounts = (((int16_t)_buffer[3 + _enFifoAccel*6 + _enFifoTemp*2 + _enFifoGyro*6]) << 8) | _buffer[2 + _enFifoAccel*6 + _enFifoTemp*2 + _enFifoGyro*6];
+ _hzcounts = (((int16_t)_buffer[5 + _enFifoAccel*6 + _enFifoTemp*2 + _enFifoGyro*6]) << 8) | _buffer[4 + _enFifoAccel*6 + _enFifoTemp*2 + _enFifoGyro*6];
+ // transform and convert to float values
+ _hxFifo[i] = (((float)(_hxcounts) * _magScaleX) - _hxb)*_hxs;
+ _hyFifo[i] = (((float)(_hycounts) * _magScaleY) - _hyb)*_hys;
+ _hzFifo[i] = (((float)(_hzcounts) * _magScaleZ) - _hzb)*_hzs;
+ _hSize = _fifoSize/_fifoFrameSize;
+ }
+ }
+ return 1;
+}
+
+/* returns the accelerometer FIFO size and data in the x direction, m/s/s */
+void MPU9250FIFO::getFifoAccelX_mss(size_t *size,float* data) {
+ *size = _aSize;
+ memcpy(data,_axFifo,_aSize*sizeof(float));
+}
+
+/* returns the accelerometer FIFO size and data in the y direction, m/s/s */
+void MPU9250FIFO::getFifoAccelY_mss(size_t *size,float* data) {
+ *size = _aSize;
+ memcpy(data,_ayFifo,_aSize*sizeof(float));
+}
+
+/* returns the accelerometer FIFO size and data in the z direction, m/s/s */
+void MPU9250FIFO::getFifoAccelZ_mss(size_t *size,float* data) {
+ *size = _aSize;
+ memcpy(data,_azFifo,_aSize*sizeof(float));
+}
+
+/* returns the gyroscope FIFO size and data in the x direction, rad/s */
+void MPU9250FIFO::getFifoGyroX_rads(size_t *size,float* data) {
+ *size = _gSize;
+ memcpy(data,_gxFifo,_gSize*sizeof(float));
+}
+
+/* returns the gyroscope FIFO size and data in the y direction, rad/s */
+void MPU9250FIFO::getFifoGyroY_rads(size_t *size,float* data) {
+ *size = _gSize;
+ memcpy(data,_gyFifo,_gSize*sizeof(float));
+}
+
+/* returns the gyroscope FIFO size and data in the z direction, rad/s */
+void MPU9250FIFO::getFifoGyroZ_rads(size_t *size,float* data) {
+ *size = _gSize;
+ memcpy(data,_gzFifo,_gSize*sizeof(float));
+}
+
+/* returns the magnetometer FIFO size and data in the x direction, uT */
+void MPU9250FIFO::getFifoMagX_uT(size_t *size,float* data) {
+ *size = _hSize;
+ memcpy(data,_hxFifo,_hSize*sizeof(float));
+}
+
+/* returns the magnetometer FIFO size and data in the y direction, uT */
+void MPU9250FIFO::getFifoMagY_uT(size_t *size,float* data) {
+ *size = _hSize;
+ memcpy(data,_hyFifo,_hSize*sizeof(float));
+}
+
+/* returns the magnetometer FIFO size and data in the z direction, uT */
+void MPU9250FIFO::getFifoMagZ_uT(size_t *size,float* data) {
+ *size = _hSize;
+ memcpy(data,_hzFifo,_hSize*sizeof(float));
+}
+
+/* returns the die temperature FIFO size and data, C */
+void MPU9250FIFO::getFifoTemperature_C(size_t *size,float* data) {
+ *size = _tSize;
+ memcpy(data,_tFifo,_tSize*sizeof(float));
+}
+
+/* estimates the gyro biases */
+int MPU9250::calibrateGyro() {
+ // set the range, bandwidth, and srd
+ if (setGyroRange(GYRO_RANGE_250DPS) < 0) {
+ return -1;
+ }
+ if (setDlpfBandwidth(DLPF_BANDWIDTH_20HZ) < 0) {
+ return -2;
+ }
+ if (setSrd(19) < 0) {
+ return -3;
+ }
+
+ // take samples and find bias
+ _gxbD = 0;
+ _gybD = 0;
+ _gzbD = 0;
+ for (size_t i=0; i < _numSamples; i++) {
+ readSensor();
+ _gxbD += (getGyroX_rads() + _gxb)/((double)_numSamples);
+ _gybD += (getGyroY_rads() + _gyb)/((double)_numSamples);
+ _gzbD += (getGyroZ_rads() + _gzb)/((double)_numSamples);
+ delay(20);
+ }
+ _gxb = (float)_gxbD;
+ _gyb = (float)_gybD;
+ _gzb = (float)_gzbD;
+
+ // set the range, bandwidth, and srd back to what they were
+ if (setGyroRange(_gyroRange) < 0) {
+ return -4;
+ }
+ if (setDlpfBandwidth(_bandwidth) < 0) {
+ return -5;
+ }
+ if (setSrd(_srd) < 0) {
+ return -6;
+ }
+ return 1;
+}
+
+/* returns the gyro bias in the X direction, rad/s */
+float MPU9250::getGyroBiasX_rads() {
+ return _gxb;
+}
+
+/* returns the gyro bias in the Y direction, rad/s */
+float MPU9250::getGyroBiasY_rads() {
+ return _gyb;
+}
+
+/* returns the gyro bias in the Z direction, rad/s */
+float MPU9250::getGyroBiasZ_rads() {
+ return _gzb;
+}
+
+/* sets the gyro bias in the X direction to bias, rad/s */
+void MPU9250::setGyroBiasX_rads(float bias) {
+ _gxb = bias;
+}
+
+/* sets the gyro bias in the Y direction to bias, rad/s */
+void MPU9250::setGyroBiasY_rads(float bias) {
+ _gyb = bias;
+}
+
+/* sets the gyro bias in the Z direction to bias, rad/s */
+void MPU9250::setGyroBiasZ_rads(float bias) {
+ _gzb = bias;
+}
+
+/* finds bias and scale factor calibration for the accelerometer,
+this should be run for each axis in each direction (6 total) to find
+the min and max values along each */
+int MPU9250::calibrateAccel() {
+ // set the range, bandwidth, and srd
+ if (setAccelRange(ACCEL_RANGE_2G) < 0) {
+ return -1;
+ }
+ if (setDlpfBandwidth(DLPF_BANDWIDTH_20HZ) < 0) {
+ return -2;
+ }
+ if (setSrd(19) < 0) {
+ return -3;
+ }
+
+ // take samples and find min / max
+ _axbD = 0;
+ _aybD = 0;
+ _azbD = 0;
+ for (size_t i=0; i < _numSamples; i++) {
+ readSensor();
+ _axbD += (getAccelX_mss()/_axs + _axb)/((double)_numSamples);
+ _aybD += (getAccelY_mss()/_ays + _ayb)/((double)_numSamples);
+ _azbD += (getAccelZ_mss()/_azs + _azb)/((double)_numSamples);
+ delay(20);
+ }
+ if (_axbD > 9.0f) {
+ _axmax = (float)_axbD;
+ }
+ if (_aybD > 9.0f) {
+ _aymax = (float)_aybD;
+ }
+ if (_azbD > 9.0f) {
+ _azmax = (float)_azbD;
+ }
+ if (_axbD < -9.0f) {
+ _axmin = (float)_axbD;
+ }
+ if (_aybD < -9.0f) {
+ _aymin = (float)_aybD;
+ }
+ if (_azbD < -9.0f) {
+ _azmin = (float)_azbD;
+ }
+
+ // find bias and scale factor
+ if ((abs(_axmin) > 9.0f) && (abs(_axmax) > 9.0f)) {
+ _axb = (_axmin + _axmax) / 2.0f;
+ _axs = G/((abs(_axmin) + abs(_axmax)) / 2.0f);
+ }
+ if ((abs(_aymin) > 9.0f) && (abs(_aymax) > 9.0f)) {
+ _ayb = (_aymin + _aymax) / 2.0f;
+ _ays = G/((abs(_aymin) + abs(_aymax)) / 2.0f);
+ }
+ if ((abs(_azmin) > 9.0f) && (abs(_azmax) > 9.0f)) {
+ _azb = (_azmin + _azmax) / 2.0f;
+ _azs = G/((abs(_azmin) + abs(_azmax)) / 2.0f);
+ }
+
+ // set the range, bandwidth, and srd back to what they were
+ if (setAccelRange(_accelRange) < 0) {
+ return -4;
+ }
+ if (setDlpfBandwidth(_bandwidth) < 0) {
+ return -5;
+ }
+ if (setSrd(_srd) < 0) {
+ return -6;
+ }
+ return 1;
+}
+
+/* returns the accelerometer bias in the X direction, m/s/s */
+float MPU9250::getAccelBiasX_mss() {
+ return _axb;
+}
+
+/* returns the accelerometer scale factor in the X direction */
+float MPU9250::getAccelScaleFactorX() {
+ return _axs;
+}
+
+/* returns the accelerometer bias in the Y direction, m/s/s */
+float MPU9250::getAccelBiasY_mss() {
+ return _ayb;
+}
+
+/* returns the accelerometer scale factor in the Y direction */
+float MPU9250::getAccelScaleFactorY() {
+ return _ays;
+}
+
+/* returns the accelerometer bias in the Z direction, m/s/s */
+float MPU9250::getAccelBiasZ_mss() {
+ return _azb;
+}
+
+/* returns the accelerometer scale factor in the Z direction */
+float MPU9250::getAccelScaleFactorZ() {
+ return _azs;
+}
+
+/* sets the accelerometer bias (m/s/s) and scale factor in the X direction */
+void MPU9250::setAccelCalX(float bias,float scaleFactor) {
+ _axb = bias;
+ _axs = scaleFactor;
+}
+
+/* sets the accelerometer bias (m/s/s) and scale factor in the Y direction */
+void MPU9250::setAccelCalY(float bias,float scaleFactor) {
+ _ayb = bias;
+ _ays = scaleFactor;
+}
+
+/* sets the accelerometer bias (m/s/s) and scale factor in the Z direction */
+void MPU9250::setAccelCalZ(float bias,float scaleFactor) {
+ _azb = bias;
+ _azs = scaleFactor;
+}
+
+/* finds bias and scale factor calibration for the magnetometer,
+the sensor should be rotated in a figure 8 motion until complete */
+int MPU9250::calibrateMag() {
+ // set the srd
+ if (setSrd(19) < 0) {
+ return -1;
+ }
+
+ // get a starting set of data
+ readSensor();
+ _hxmax = getMagX_uT();
+ _hxmin = getMagX_uT();
+ _hymax = getMagY_uT();
+ _hymin = getMagY_uT();
+ _hzmax = getMagZ_uT();
+ _hzmin = getMagZ_uT();
+
+ // collect data to find max / min in each channel
+ _counter = 0;
+ while (_counter < _maxCounts) {
+ _delta = 0.0f;
+ _framedelta = 0.0f;
+ readSensor();
+ _hxfilt = (_hxfilt*((float)_coeff-1)+(getMagX_uT()/_hxs+_hxb))/((float)_coeff);
+ _hyfilt = (_hyfilt*((float)_coeff-1)+(getMagY_uT()/_hys+_hyb))/((float)_coeff);
+ _hzfilt = (_hzfilt*((float)_coeff-1)+(getMagZ_uT()/_hzs+_hzb))/((float)_coeff);
+ if (_hxfilt > _hxmax) {
+ _delta = _hxfilt - _hxmax;
+ _hxmax = _hxfilt;
+ }
+ if (_delta > _framedelta) {
+ _framedelta = _delta;
+ }
+ if (_hyfilt > _hymax) {
+ _delta = _hyfilt - _hymax;
+ _hymax = _hyfilt;
+ }
+ if (_delta > _framedelta) {
+ _framedelta = _delta;
+ }
+ if (_hzfilt > _hzmax) {
+ _delta = _hzfilt - _hzmax;
+ _hzmax = _hzfilt;
+ }
+ if (_delta > _framedelta) {
+ _framedelta = _delta;
+ }
+ if (_hxfilt < _hxmin) {
+ _delta = abs(_hxfilt - _hxmin);
+ _hxmin = _hxfilt;
+ }
+ if (_delta > _framedelta) {
+ _framedelta = _delta;
+ }
+ if (_hyfilt < _hymin) {
+ _delta = abs(_hyfilt - _hymin);
+ _hymin = _hyfilt;
+ }
+ if (_delta > _framedelta) {
+ _framedelta = _delta;
+ }
+ if (_hzfilt < _hzmin) {
+ _delta = abs(_hzfilt - _hzmin);
+ _hzmin = _hzfilt;
+ }
+ if (_delta > _framedelta) {
+ _framedelta = _delta;
+ }
+ if (_framedelta > _deltaThresh) {
+ _counter = 0;
+ } else {
+ _counter++;
+ }
+ delay(20);
+ }
+
+ // find the magnetometer bias
+ _hxb = (_hxmax + _hxmin) / 2.0f;
+ _hyb = (_hymax + _hymin) / 2.0f;
+ _hzb = (_hzmax + _hzmin) / 2.0f;
+
+ // find the magnetometer scale factor
+ _hxs = (_hxmax - _hxmin) / 2.0f;
+ _hys = (_hymax - _hymin) / 2.0f;
+ _hzs = (_hzmax - _hzmin) / 2.0f;
+ _avgs = (_hxs + _hys + _hzs) / 3.0f;
+ _hxs = _avgs/_hxs;
+ _hys = _avgs/_hys;
+ _hzs = _avgs/_hzs;
+
+ // set the srd back to what it was
+ if (setSrd(_srd) < 0) {
+ return -2;
+ }
+ return 1;
+}
+
+/* returns the magnetometer bias in the X direction, uT */
+float MPU9250::getMagBiasX_uT() {
+ return _hxb;
+}
+
+/* returns the magnetometer scale factor in the X direction */
+float MPU9250::getMagScaleFactorX() {
+ return _hxs;
+}
+
+/* returns the magnetometer bias in the Y direction, uT */
+float MPU9250::getMagBiasY_uT() {
+ return _hyb;
+}
+
+/* returns the magnetometer scale factor in the Y direction */
+float MPU9250::getMagScaleFactorY() {
+ return _hys;
+}
+
+/* returns the magnetometer bias in the Z direction, uT */
+float MPU9250::getMagBiasZ_uT() {
+ return _hzb;
+}
+
+/* returns the magnetometer scale factor in the Z direction */
+float MPU9250::getMagScaleFactorZ() {
+ return _hzs;
+}
+
+/* sets the magnetometer bias (uT) and scale factor in the X direction */
+void MPU9250::setMagCalX(float bias,float scaleFactor) {
+ _hxb = bias;
+ _hxs = scaleFactor;
+}
+
+/* sets the magnetometer bias (uT) and scale factor in the Y direction */
+void MPU9250::setMagCalY(float bias,float scaleFactor) {
+ _hyb = bias;
+ _hys = scaleFactor;
+}
+
+/* sets the magnetometer bias (uT) and scale factor in the Z direction */
+void MPU9250::setMagCalZ(float bias,float scaleFactor) {
+ _hzb = bias;
+ _hzs = scaleFactor;
+}
+
+#if defined(__IMXRT1062__)
+/* writes a byte to MPU9250 register given a register address and data */
+int MPU9250::writeRegister(uint8_t subAddress, uint8_t data){
+ /* write data to device */
+ if( _useSPI ){
+ _spi->beginTransaction(SPISettings(SPI_LS_CLOCK, MSBFIRST, SPI_MODE3)); // begin the transaction
+ digitalWriteFast(_csPin,LOW); // select the MPU9250 chip
+ delayNanoseconds(200);
+ _spi->transfer(subAddress); // write the register address
+ _spi->transfer(data); // write the data
+ digitalWriteFast(_csPin,HIGH); // deselect the MPU9250 chip
+ delayNanoseconds(200);
+ _spi->endTransaction(); // end the transaction
+ }
+ else{
+ _i2c->beginTransmission(_address); // open the device
+ _i2c->write(subAddress); // write the register address
+ _i2c->write(data); // write the data
+ _i2c->endTransmission();
+ }
+
+ delay(10);
+
+ /* read back the register */
+ readRegisters(subAddress,1,_buffer);
+ /* check the read back register against the written register */
+ if(_buffer[0] == data) {
+ return 1;
+ }
+ else{
+ return -1;
+ }
+}
+
+/* reads registers from MPU9250 given a starting register address, number of bytes, and a pointer to store data */
+int MPU9250::readRegisters(uint8_t subAddress, uint8_t count, uint8_t* dest){
+ if( _useSPI ){
+ // begin the transaction
+ if(_useSPIHS){
+ _spi->beginTransaction(SPISettings(SPI_HS_CLOCK, MSBFIRST, SPI_MODE3));
+ }
+ else{
+ _spi->beginTransaction(SPISettings(SPI_LS_CLOCK, MSBFIRST, SPI_MODE3));
+ }
+ digitalWriteFast(_csPin,LOW); // select the MPU9250 chip
+ delayNanoseconds(200);
+ _spi->transfer(subAddress | SPI_READ); // specify the starting register address
+ for(uint8_t i = 0; i < count; i++){
+ dest[i] = _spi->transfer(0x00); // read the data
+ }
+ digitalWriteFast(_csPin,HIGH); // deselect the MPU9250 chip
+ delayNanoseconds(200);
+ _spi->endTransaction(); // end the transaction
+ return 1;
+ }
+ else{
+ _i2c->beginTransmission(_address); // open the device
+ _i2c->write(subAddress); // specify the starting register address
+ _i2c->endTransmission(false);
+ _numBytes = _i2c->requestFrom(_address, count); // specify the number of bytes to receive
+ if (_numBytes == count) {
+ for(uint8_t i = 0; i < count; i++){
+ dest[i] = _i2c->read();
+ }
+ return 1;
+ } else {
+ return -1;
+ }
+ }
+}
+#else
+/* writes a byte to MPU9250 register given a register address and data */
+int MPU9250::writeRegister(uint8_t subAddress, uint8_t data){
+ /* write data to device */
+ if( _useSPI ){
+ _spi->beginTransaction(SPISettings(SPI_LS_CLOCK, MSBFIRST, SPI_MODE3)); // begin the transaction
+ digitalWrite(_csPin,LOW); // select the MPU9250 chip
+ _spi->transfer(subAddress); // write the register address
+ _spi->transfer(data); // write the data
+ digitalWrite(_csPin,HIGH); // deselect the MPU9250 chip
+ _spi->endTransaction(); // end the transaction
+ }
+ else{
+ _i2c->beginTransmission(_address); // open the device
+ _i2c->write(subAddress); // write the register address
+ _i2c->write(data); // write the data
+ _i2c->endTransmission();
+ }
+
+ delay(10);
+
+ /* read back the register */
+ readRegisters(subAddress,1,_buffer);
+ /* check the read back register against the written register */
+ if(_buffer[0] == data) {
+ return 1;
+ }
+ else{
+ return -1;
+ }
+}
+
+/* reads registers from MPU9250 given a starting register address, number of bytes, and a pointer to store data */
+int MPU9250::readRegisters(uint8_t subAddress, uint8_t count, uint8_t* dest){
+ if( _useSPI ){
+ // begin the transaction
+ if(_useSPIHS){
+ _spi->beginTransaction(SPISettings(SPI_HS_CLOCK, MSBFIRST, SPI_MODE3));
+ }
+ else{
+ _spi->beginTransaction(SPISettings(SPI_LS_CLOCK, MSBFIRST, SPI_MODE3));
+ }
+ digitalWrite(_csPin,LOW); // select the MPU9250 chip
+ _spi->transfer(subAddress | SPI_READ); // specify the starting register address
+ for(uint8_t i = 0; i < count; i++){
+ dest[i] = _spi->transfer(0x00); // read the data
+ }
+ digitalWrite(_csPin,HIGH); // deselect the MPU9250 chip
+ _spi->endTransaction(); // end the transaction
+ return 1;
+ }
+ else{
+ _i2c->beginTransmission(_address); // open the device
+ _i2c->write(subAddress); // specify the starting register address
+ _i2c->endTransmission(false);
+ _numBytes = _i2c->requestFrom(_address, count); // specify the number of bytes to receive
+ if (_numBytes == count) {
+ for(uint8_t i = 0; i < count; i++){
+ dest[i] = _i2c->read();
+ }
+ return 1;
+ } else {
+ return -1;
+ }
+ }
+}
+#endif
+
+/* writes a register to the AK8963 given a register address and data */
+int MPU9250::writeAK8963Register(uint8_t subAddress, uint8_t data){
+ // set slave 0 to the AK8963 and set for write
+ if (writeRegister(I2C_SLV0_ADDR,AK8963_I2C_ADDR) < 0) {
+ return -1;
+ }
+ // set the register to the desired AK8963 sub address
+ if (writeRegister(I2C_SLV0_REG,subAddress) < 0) {
+ return -2;
+ }
+ // store the data for write
+ if (writeRegister(I2C_SLV0_DO,data) < 0) {
+ return -3;
+ }
+ // enable I2C and send 1 byte
+ if (writeRegister(I2C_SLV0_CTRL,I2C_SLV0_EN | (uint8_t)1) < 0) {
+ return -4;
+ }
+ // read the register and confirm
+ if (readAK8963Registers(subAddress,1,_buffer) < 0) {
+ return -5;
+ }
+ if(_buffer[0] == data) {
+ return 1;
+ } else{
+ return -6;
+ }
+}
+
+/* reads registers from the AK8963 */
+int MPU9250::readAK8963Registers(uint8_t subAddress, uint8_t count, uint8_t* dest){
+ // set slave 0 to the AK8963 and set for read
+ if (writeRegister(I2C_SLV0_ADDR,AK8963_I2C_ADDR | I2C_READ_FLAG) < 0) {
+ return -1;
+ }
+ // set the register to the desired AK8963 sub address
+ if (writeRegister(I2C_SLV0_REG,subAddress) < 0) {
+ return -2;
+ }
+ // enable I2C and request the bytes
+ if (writeRegister(I2C_SLV0_CTRL,I2C_SLV0_EN | count) < 0) {
+ return -3;
+ }
+ delay(1); // takes some time for these registers to fill
+ // read the bytes off the MPU9250 EXT_SENS_DATA registers
+ _status = readRegisters(EXT_SENS_DATA_00,count,dest);
+ return _status;
+}
+
+/* gets the MPU9250 WHO_AM_I register value, expected to be 0x71 */
+int MPU9250::whoAmI(){
+ // read the WHO AM I register
+ if (readRegisters(WHO_AM_I,1,_buffer) < 0) {
+ return -1;
+ }
+ // return the register value
+ return _buffer[0];
+}
+
+/* gets the AK8963 WHO_AM_I register value, expected to be 0x48 */
+int MPU9250::whoAmIAK8963(){
+ // read the WHO AM I register
+ if (readAK8963Registers(AK8963_WHO_AM_I,1,_buffer) < 0) {
+ return -1;
+ }
+ // return the register value
+ return _buffer[0];
+}
+
+// jihlein additions start
+
+void MPU9250::getMotion6(int16_t* ax, int16_t* ay, int16_t* az, int16_t* gx, int16_t* gy, int16_t* gz) {
+ uint8_t buffer[14];
+ readRegisters(ACCEL_OUT, 14, buffer);
+ *ax = (((int16_t)buffer[0]) << 8) | buffer[1];
+ *ay = (((int16_t)buffer[2]) << 8) | buffer[3];
+ *az = (((int16_t)buffer[4]) << 8) | buffer[5];
+ *gx = (((int16_t)buffer[8]) << 8) | buffer[9];
+ *gy = (((int16_t)buffer[10]) << 8) | buffer[11];
+ *gz = (((int16_t)buffer[12]) << 8) | buffer[13];
+}
+
+void MPU9250::getMotion9(int16_t* ax, int16_t* ay, int16_t* az, int16_t* gx, int16_t* gy, int16_t* gz, int16_t* mx, int16_t* my, int16_t* mz) {
+ uint8_t buffer[20];
+ readRegisters(ACCEL_OUT, 20, buffer);
+ *ax = (((int16_t)buffer[0]) << 8) | buffer[1];
+ *ay = (((int16_t)buffer[2]) << 8) | buffer[3];
+ *az = (((int16_t)buffer[4]) << 8) | buffer[5];
+ *gx = (((int16_t)buffer[8]) << 8) | buffer[9];
+ *gy = (((int16_t)buffer[10]) << 8) | buffer[11];
+ *gz = (((int16_t)buffer[12]) << 8) | buffer[13];
+ *mx = (((int16_t)buffer[15]) << 8) | buffer[14];
+ *my = (((int16_t)buffer[17]) << 8) | buffer[16];
+ *mz = (((int16_t)buffer[19]) << 8) | buffer[18];
+}
+
+// jihlein additions end
\ No newline at end of file
diff --git a/Versions/dRehmFlight_ESP32_BETA_1.3/src/MPU9250/MPU9250.h b/Versions/dRehmFlight_ESP32_BETA_1.3/src/MPU9250/MPU9250.h
new file mode 100644
index 00000000..bbbe2c5a
--- /dev/null
+++ b/Versions/dRehmFlight_ESP32_BETA_1.3/src/MPU9250/MPU9250.h
@@ -0,0 +1,313 @@
+/*
+ MPU9250.h
+ Brian R Taylor
+ [email protected]
+
+ Copyright (c) 2017 Bolder Flight Systems
+
+ This program is free software: you can redistribute it and/or modify
+ it under the terms of the GNU General Public License as published by
+ the Free Software Foundation, either version 3 of the License, or
+ (at your option) any later version.
+
+ This program is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ GNU General Public License for more details.
+
+ You should have received a copy of the GNU General Public License
+ along with this program. If not, see .
+*/
+
+#ifndef MPU9250_h
+#define MPU9250_h
+
+#include "Arduino.h"
+#include "Wire.h" // I2C library
+#include "SPI.h" // SPI library
+
+class MPU9250{
+ public:
+ enum GyroRange
+ {
+ GYRO_RANGE_250DPS,
+ GYRO_RANGE_500DPS,
+ GYRO_RANGE_1000DPS,
+ GYRO_RANGE_2000DPS
+ };
+ enum AccelRange
+ {
+ ACCEL_RANGE_2G,
+ ACCEL_RANGE_4G,
+ ACCEL_RANGE_8G,
+ ACCEL_RANGE_16G
+ };
+ enum DlpfBandwidth
+ {
+ DLPF_BANDWIDTH_184HZ,
+ DLPF_BANDWIDTH_92HZ,
+ DLPF_BANDWIDTH_41HZ,
+ DLPF_BANDWIDTH_20HZ,
+ DLPF_BANDWIDTH_10HZ,
+ DLPF_BANDWIDTH_5HZ
+ };
+ enum LpAccelOdr
+ {
+ LP_ACCEL_ODR_0_24HZ = 0,
+ LP_ACCEL_ODR_0_49HZ = 1,
+ LP_ACCEL_ODR_0_98HZ = 2,
+ LP_ACCEL_ODR_1_95HZ = 3,
+ LP_ACCEL_ODR_3_91HZ = 4,
+ LP_ACCEL_ODR_7_81HZ = 5,
+ LP_ACCEL_ODR_15_63HZ = 6,
+ LP_ACCEL_ODR_31_25HZ = 7,
+ LP_ACCEL_ODR_62_50HZ = 8,
+ LP_ACCEL_ODR_125HZ = 9,
+ LP_ACCEL_ODR_250HZ = 10,
+ LP_ACCEL_ODR_500HZ = 11
+ };
+ MPU9250(TwoWire &bus,uint8_t address);
+ MPU9250(SPIClass &bus,uint8_t csPin);
+ int begin();
+ int setAccelRange(AccelRange range);
+ int setGyroRange(GyroRange range);
+ int setDlpfBandwidth(DlpfBandwidth bandwidth);
+ int setSrd(uint8_t srd);
+ int enableDataReadyInterrupt();
+ int disableDataReadyInterrupt();
+ int enableWakeOnMotion(float womThresh_mg,LpAccelOdr odr);
+ int readSensor();
+ float getAccelX_mss();
+ float getAccelY_mss();
+ float getAccelZ_mss();
+ float getGyroX_rads();
+ float getGyroY_rads();
+ float getGyroZ_rads();
+ float getMagX_uT();
+ float getMagY_uT();
+ float getMagZ_uT();
+ float getTemperature_C();
+
+ int calibrateGyro();
+ float getGyroBiasX_rads();
+ float getGyroBiasY_rads();
+ float getGyroBiasZ_rads();
+ void setGyroBiasX_rads(float bias);
+ void setGyroBiasY_rads(float bias);
+ void setGyroBiasZ_rads(float bias);
+ int calibrateAccel();
+ float getAccelBiasX_mss();
+ float getAccelScaleFactorX();
+ float getAccelBiasY_mss();
+ float getAccelScaleFactorY();
+ float getAccelBiasZ_mss();
+ float getAccelScaleFactorZ();
+ void setAccelCalX(float bias,float scaleFactor);
+ void setAccelCalY(float bias,float scaleFactor);
+ void setAccelCalZ(float bias,float scaleFactor);
+ int calibrateMag();
+ float getMagBiasX_uT();
+ float getMagScaleFactorX();
+ float getMagBiasY_uT();
+ float getMagScaleFactorY();
+ float getMagBiasZ_uT();
+ float getMagScaleFactorZ();
+ void setMagCalX(float bias,float scaleFactor);
+ void setMagCalY(float bias,float scaleFactor);
+ void setMagCalZ(float bias,float scaleFactor);
+ // jihlein additions start
+ void getMotion9(int16_t* ax, int16_t* ay, int16_t* az, int16_t* gx, int16_t* gy, int16_t* gz, int16_t* mx, int16_t* my, int16_t* mz);
+ void getMotion6(int16_t* ax, int16_t* ay, int16_t* az, int16_t* gx, int16_t* gy, int16_t* gz);
+ // jihlein additions end
+ protected:
+ // i2c
+ uint8_t _address;
+ TwoWire *_i2c;
+ const uint32_t _i2cRate = 400000; // 400 kHz
+ size_t _numBytes; // number of bytes received from I2C
+ // spi
+ SPIClass *_spi;
+ uint8_t _csPin;
+ bool _useSPI;
+ bool _useSPIHS;
+ const uint8_t SPI_READ = 0x80;
+ const uint32_t SPI_LS_CLOCK = 1000000; // 1 MHz
+ const uint32_t SPI_HS_CLOCK = 15000000; // 15 MHz
+ // track success of interacting with sensor
+ int _status;
+ // buffer for reading from sensor
+ uint8_t _buffer[21];
+ // data counts
+ int16_t _axcounts,_aycounts,_azcounts;
+ int16_t _gxcounts,_gycounts,_gzcounts;
+ int16_t _hxcounts,_hycounts,_hzcounts;
+ int16_t _tcounts;
+ // data buffer
+ float _ax, _ay, _az;
+ float _gx, _gy, _gz;
+ float _hx, _hy, _hz;
+ float _t;
+ // wake on motion
+ uint8_t _womThreshold;
+ // scale factors
+ float _accelScale;
+ float _gyroScale;
+ float _magScaleX, _magScaleY, _magScaleZ;
+ const float _tempScale = 333.87f;
+ const float _tempOffset = 21.0f;
+ // configuration
+ AccelRange _accelRange;
+ GyroRange _gyroRange;
+ DlpfBandwidth _bandwidth;
+ uint8_t _srd;
+ // gyro bias estimation
+ size_t _numSamples = 100;
+ double _gxbD, _gybD, _gzbD;
+ float _gxb, _gyb, _gzb;
+ // accel bias and scale factor estimation
+ double _axbD, _aybD, _azbD;
+ float _axmax, _aymax, _azmax;
+ float _axmin, _aymin, _azmin;
+ float _axb, _ayb, _azb;
+ float _axs = 1.0f;
+ float _ays = 1.0f;
+ float _azs = 1.0f;
+ // magnetometer bias and scale factor estimation
+ uint16_t _maxCounts = 1000;
+ float _deltaThresh = 0.3f;
+ uint8_t _coeff = 8;
+ uint16_t _counter;
+ float _framedelta, _delta;
+ float _hxfilt, _hyfilt, _hzfilt;
+ float _hxmax, _hymax, _hzmax;
+ float _hxmin, _hymin, _hzmin;
+ float _hxb, _hyb, _hzb;
+ float _hxs = 1.0f;
+ float _hys = 1.0f;
+ float _hzs = 1.0f;
+ float _avgs;
+ // transformation matrix
+ /* transform the accel and gyro axes to match the magnetometer axes */
+ const int16_t tX[3] = {0, 1, 0};
+ const int16_t tY[3] = {1, 0, 0};
+ const int16_t tZ[3] = {0, 0, -1};
+ // constants
+ const float G = 9.807f;
+ const float _d2r = 3.14159265359f/180.0f;
+ // MPU9250 registers
+ const uint8_t ACCEL_OUT = 0x3B;
+ const uint8_t GYRO_OUT = 0x43;
+ const uint8_t TEMP_OUT = 0x41;
+ const uint8_t EXT_SENS_DATA_00 = 0x49;
+ const uint8_t ACCEL_CONFIG = 0x1C;
+ const uint8_t ACCEL_FS_SEL_2G = 0x00;
+ const uint8_t ACCEL_FS_SEL_4G = 0x08;
+ const uint8_t ACCEL_FS_SEL_8G = 0x10;
+ const uint8_t ACCEL_FS_SEL_16G = 0x18;
+ const uint8_t GYRO_CONFIG = 0x1B;
+ const uint8_t GYRO_FS_SEL_250DPS = 0x00;
+ const uint8_t GYRO_FS_SEL_500DPS = 0x08;
+ const uint8_t GYRO_FS_SEL_1000DPS = 0x10;
+ const uint8_t GYRO_FS_SEL_2000DPS = 0x18;
+ const uint8_t ACCEL_CONFIG2 = 0x1D;
+ const uint8_t ACCEL_DLPF_184 = 0x01;
+ const uint8_t ACCEL_DLPF_92 = 0x02;
+ const uint8_t ACCEL_DLPF_41 = 0x03;
+ const uint8_t ACCEL_DLPF_20 = 0x04;
+ const uint8_t ACCEL_DLPF_10 = 0x05;
+ const uint8_t ACCEL_DLPF_5 = 0x06;
+ const uint8_t CONFIG = 0x1A;
+ const uint8_t GYRO_DLPF_184 = 0x01;
+ const uint8_t GYRO_DLPF_92 = 0x02;
+ const uint8_t GYRO_DLPF_41 = 0x03;
+ const uint8_t GYRO_DLPF_20 = 0x04;
+ const uint8_t GYRO_DLPF_10 = 0x05;
+ const uint8_t GYRO_DLPF_5 = 0x06;
+ const uint8_t SMPDIV = 0x19;
+ const uint8_t INT_PIN_CFG = 0x37;
+ const uint8_t INT_ENABLE = 0x38;
+ const uint8_t INT_DISABLE = 0x00;
+ const uint8_t INT_PULSE_50US = 0x00;
+ const uint8_t INT_WOM_EN = 0x40;
+ const uint8_t INT_RAW_RDY_EN = 0x01;
+ const uint8_t PWR_MGMNT_1 = 0x6B;
+ const uint8_t PWR_CYCLE = 0x20;
+ const uint8_t PWR_RESET = 0x80;
+ const uint8_t CLOCK_SEL_PLL = 0x01;
+ const uint8_t PWR_MGMNT_2 = 0x6C;
+ const uint8_t SEN_ENABLE = 0x00;
+ const uint8_t DIS_GYRO = 0x07;
+ const uint8_t USER_CTRL = 0x6A;
+ const uint8_t I2C_MST_EN = 0x20;
+ const uint8_t I2C_MST_CLK = 0x0D;
+ const uint8_t I2C_MST_CTRL = 0x24;
+ const uint8_t I2C_SLV0_ADDR = 0x25;
+ const uint8_t I2C_SLV0_REG = 0x26;
+ const uint8_t I2C_SLV0_DO = 0x63;
+ const uint8_t I2C_SLV0_CTRL = 0x27;
+ const uint8_t I2C_SLV0_EN = 0x80;
+ const uint8_t I2C_READ_FLAG = 0x80;
+ const uint8_t MOT_DETECT_CTRL = 0x69;
+ const uint8_t ACCEL_INTEL_EN = 0x80;
+ const uint8_t ACCEL_INTEL_MODE = 0x40;
+ const uint8_t LP_ACCEL_ODR = 0x1E;
+ const uint8_t WOM_THR = 0x1F;
+ const uint8_t WHO_AM_I = 0x75;
+ const uint8_t FIFO_EN = 0x23;
+ const uint8_t FIFO_TEMP = 0x80;
+ const uint8_t FIFO_GYRO = 0x70;
+ const uint8_t FIFO_ACCEL = 0x08;
+ const uint8_t FIFO_MAG = 0x01;
+ const uint8_t FIFO_COUNT = 0x72;
+ const uint8_t FIFO_READ = 0x74;
+ // AK8963 registers
+ const uint8_t AK8963_I2C_ADDR = 0x0C;
+ const uint8_t AK8963_HXL = 0x03;
+ const uint8_t AK8963_CNTL1 = 0x0A;
+ const uint8_t AK8963_PWR_DOWN = 0x00;
+ const uint8_t AK8963_CNT_MEAS1 = 0x12;
+ const uint8_t AK8963_CNT_MEAS2 = 0x16;
+ const uint8_t AK8963_FUSE_ROM = 0x0F;
+ const uint8_t AK8963_CNTL2 = 0x0B;
+ const uint8_t AK8963_RESET = 0x01;
+ const uint8_t AK8963_ASA = 0x10;
+ const uint8_t AK8963_WHO_AM_I = 0x00;
+ // private functions
+ int writeRegister(uint8_t subAddress, uint8_t data);
+ int readRegisters(uint8_t subAddress, uint8_t count, uint8_t* dest);
+ int writeAK8963Register(uint8_t subAddress, uint8_t data);
+ int readAK8963Registers(uint8_t subAddress, uint8_t count, uint8_t* dest);
+ int whoAmI();
+ int whoAmIAK8963();
+};
+
+class MPU9250FIFO: public MPU9250 {
+ public:
+ using MPU9250::MPU9250;
+ int enableFifo(bool accel,bool gyro,bool mag,bool temp);
+ int readFifo();
+ void getFifoAccelX_mss(size_t *size,float* data);
+ void getFifoAccelY_mss(size_t *size,float* data);
+ void getFifoAccelZ_mss(size_t *size,float* data);
+ void getFifoGyroX_rads(size_t *size,float* data);
+ void getFifoGyroY_rads(size_t *size,float* data);
+ void getFifoGyroZ_rads(size_t *size,float* data);
+ void getFifoMagX_uT(size_t *size,float* data);
+ void getFifoMagY_uT(size_t *size,float* data);
+ void getFifoMagZ_uT(size_t *size,float* data);
+ void getFifoTemperature_C(size_t *size,float* data);
+ protected:
+ // fifo
+ bool _enFifoAccel,_enFifoGyro,_enFifoMag,_enFifoTemp;
+ size_t _fifoSize,_fifoFrameSize;
+ float _axFifo[85], _ayFifo[85], _azFifo[85];
+ size_t _aSize;
+ float _gxFifo[85], _gyFifo[85], _gzFifo[85];
+ size_t _gSize;
+ float _hxFifo[73], _hyFifo[73], _hzFifo[73];
+ size_t _hSize;
+ float _tFifo[256];
+ size_t _tSize;
+};
+
+#endif
diff --git a/Versions/dRehmFlight_ESP32_BETA_1.3/src/SBUS/SBUS.cpp b/Versions/dRehmFlight_ESP32_BETA_1.3/src/SBUS/SBUS.cpp
new file mode 100644
index 00000000..07085420
--- /dev/null
+++ b/Versions/dRehmFlight_ESP32_BETA_1.3/src/SBUS/SBUS.cpp
@@ -0,0 +1,376 @@
+/*
+ SBUS.cpp
+ Brian R Taylor
+ [email protected]
+
+ Copyright (c) 2016 Bolder Flight Systems
+
+ This program is free software: you can redistribute it and/or modify
+ it under the terms of the GNU General Public License as published by
+ the Free Software Foundation, either version 3 of the License, or
+ (at your option) any later version.
+
+ This program is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ GNU General Public License for more details.
+
+ You should have received a copy of the GNU General Public License
+ along with this program. If not, see .
+*/
+
+#include "SBUS.h"
+
+// SEE: https://learn.adafruit.com/adafruit-feather-m0-basic-proto/adapting-sketches-to-m0
+#if defined(ARDUINO_SAMD_ZERO) && defined(SERIAL_PORT_USBVIRTUAL)
+ // Required for Serial on Zero based boards
+ #define Serial SERIAL_PORT_USBVIRTUAL
+#endif
+
+#if defined(__MK20DX128__) || defined(__MK20DX256__)
+ // globals needed for emulating two stop bytes on Teensy 3.0 and 3.1/3.2
+ IntervalTimer serialTimer;
+ HardwareSerial* SERIALPORT;
+ uint8_t PACKET[25];
+ volatile int SENDINDEX;
+ void sendByte();
+#endif
+/* SBUS object, input the serial bus */
+SBUS::SBUS(HardwareSerial& bus)
+{
+ _bus = &bus;
+}
+
+/* starts the serial communication */
+void SBUS::begin()
+{
+ // initialize parsing state
+ _parserState = 0;
+ // initialize default scale factors and biases
+ for (uint8_t i = 0; i < _numChannels; i++) {
+ setEndPoints(i,_defaultMin,_defaultMax);
+ }
+ // begin the serial port for SBUS
+ #if defined(__MK20DX128__) || defined(__MK20DX256__) // Teensy 3.0 || Teensy 3.1/3.2
+ _bus->begin(_sbusBaud,SERIAL_8E1_RXINV_TXINV);
+ SERIALPORT = _bus;
+ #elif defined(__IMXRT1062__) || defined(__IMXRT1052__) || defined(__MK64FX512__) || defined(__MK66FX1M0__) || defined(__MKL26Z64__) // Teensy 4.0 || Teensy 4.0 Beta || Teensy 3.5 || Teensy 3.6 || Teensy LC
+ _bus->begin(_sbusBaud,SERIAL_8E2_RXINV_TXINV);
+ #elif defined(STM32L496xx) || defined(STM32L476xx) || defined(STM32L433xx) || defined(STM32L432xx) // STM32L4
+ _bus->begin(_sbusBaud,SERIAL_SBUS);
+ #elif defined(_BOARD_MAPLE_MINI_H_) // Maple Mini
+ _bus->begin(_sbusBaud,SERIAL_8E2);
+ #elif defined(ESP32) // ESP32
+ _bus->begin(_sbusBaud,SERIAL_8E2);
+ #elif defined(__AVR_ATmega2560__) || defined(__AVR_ATmega328P__) || defined(__AVR_ATmega32U4__) // Arduino Mega 2560, 328P or 32u4
+ _bus->begin(_sbusBaud, SERIAL_8E2);
+ #elif defined(ARDUINO_SAMD_ZERO) // Adafruit Feather M0
+ _bus->begin(_sbusBaud, SERIAL_8E2);
+ #else
+ #error unsupported device
+ #endif
+}
+
+/* read the SBUS data */
+bool SBUS::read(uint16_t* channels, bool* failsafe, bool* lostFrame)
+{
+ // parse the SBUS packet
+ if (parse()) {
+ if (channels) {
+ // 16 channels of 11 bit data
+ channels[0] = (uint16_t) ((_payload[0] |_payload[1] <<8) & 0x07FF);
+ channels[1] = (uint16_t) ((_payload[1]>>3 |_payload[2] <<5) & 0x07FF);
+ channels[2] = (uint16_t) ((_payload[2]>>6 |_payload[3] <<2 |_payload[4]<<10) & 0x07FF);
+ channels[3] = (uint16_t) ((_payload[4]>>1 |_payload[5] <<7) & 0x07FF);
+ channels[4] = (uint16_t) ((_payload[5]>>4 |_payload[6] <<4) & 0x07FF);
+ channels[5] = (uint16_t) ((_payload[6]>>7 |_payload[7] <<1 |_payload[8]<<9) & 0x07FF);
+ channels[6] = (uint16_t) ((_payload[8]>>2 |_payload[9] <<6) & 0x07FF);
+ channels[7] = (uint16_t) ((_payload[9]>>5 |_payload[10]<<3) & 0x07FF);
+ channels[8] = (uint16_t) ((_payload[11] |_payload[12]<<8) & 0x07FF);
+ channels[9] = (uint16_t) ((_payload[12]>>3|_payload[13]<<5) & 0x07FF);
+ channels[10] = (uint16_t) ((_payload[13]>>6|_payload[14]<<2 |_payload[15]<<10) & 0x07FF);
+ channels[11] = (uint16_t) ((_payload[15]>>1|_payload[16]<<7) & 0x07FF);
+ channels[12] = (uint16_t) ((_payload[16]>>4|_payload[17]<<4) & 0x07FF);
+ channels[13] = (uint16_t) ((_payload[17]>>7|_payload[18]<<1 |_payload[19]<<9) & 0x07FF);
+ channels[14] = (uint16_t) ((_payload[19]>>2|_payload[20]<<6) & 0x07FF);
+ channels[15] = (uint16_t) ((_payload[20]>>5|_payload[21]<<3) & 0x07FF);
+ }
+ if (lostFrame) {
+ // count lost frames
+ if (_payload[22] & _sbusLostFrame) {
+ *lostFrame = true;
+ } else {
+ *lostFrame = false;
+ }
+ }
+ if (failsafe) {
+ // failsafe state
+ if (_payload[22] & _sbusFailSafe) {
+ *failsafe = true;
+ }
+ else{
+ *failsafe = false;
+ }
+ }
+ // return true on receiving a full packet
+ return true;
+ } else {
+ // return false if a full packet is not received
+ return false;
+ }
+}
+
+/* read the SBUS data and calibrate it to +/- 1 */
+bool SBUS::readCal(float* calChannels, bool* failsafe, bool* lostFrame)
+{
+ uint16_t channels[_numChannels];
+ // read the SBUS data
+ if(read(&channels[0],failsafe,lostFrame)) {
+ // linear calibration
+ for (uint8_t i = 0; i < _numChannels; i++) {
+ calChannels[i] = channels[i] * _sbusScale[i] + _sbusBias[i];
+ if (_useReadCoeff[i]) {
+ calChannels[i] = PolyVal(_readLen[i],_readCoeff[i],calChannels[i]);
+ }
+ }
+ // return true on receiving a full packet
+ return true;
+ } else {
+ // return false if a full packet is not received
+ return false;
+ }
+}
+
+/* write SBUS packets */
+void SBUS::write(uint16_t* channels)
+{
+ static uint8_t packet[25];
+ /* assemble the SBUS packet */
+ // SBUS header
+ packet[0] = _sbusHeader;
+ // 16 channels of 11 bit data
+ if (channels) {
+ packet[1] = (uint8_t) ((channels[0] & 0x07FF));
+ packet[2] = (uint8_t) ((channels[0] & 0x07FF)>>8 | (channels[1] & 0x07FF)<<3);
+ packet[3] = (uint8_t) ((channels[1] & 0x07FF)>>5 | (channels[2] & 0x07FF)<<6);
+ packet[4] = (uint8_t) ((channels[2] & 0x07FF)>>2);
+ packet[5] = (uint8_t) ((channels[2] & 0x07FF)>>10 | (channels[3] & 0x07FF)<<1);
+ packet[6] = (uint8_t) ((channels[3] & 0x07FF)>>7 | (channels[4] & 0x07FF)<<4);
+ packet[7] = (uint8_t) ((channels[4] & 0x07FF)>>4 | (channels[5] & 0x07FF)<<7);
+ packet[8] = (uint8_t) ((channels[5] & 0x07FF)>>1);
+ packet[9] = (uint8_t) ((channels[5] & 0x07FF)>>9 | (channels[6] & 0x07FF)<<2);
+ packet[10] = (uint8_t) ((channels[6] & 0x07FF)>>6 | (channels[7] & 0x07FF)<<5);
+ packet[11] = (uint8_t) ((channels[7] & 0x07FF)>>3);
+ packet[12] = (uint8_t) ((channels[8] & 0x07FF));
+ packet[13] = (uint8_t) ((channels[8] & 0x07FF)>>8 | (channels[9] & 0x07FF)<<3);
+ packet[14] = (uint8_t) ((channels[9] & 0x07FF)>>5 | (channels[10] & 0x07FF)<<6);
+ packet[15] = (uint8_t) ((channels[10] & 0x07FF)>>2);
+ packet[16] = (uint8_t) ((channels[10] & 0x07FF)>>10 | (channels[11] & 0x07FF)<<1);
+ packet[17] = (uint8_t) ((channels[11] & 0x07FF)>>7 | (channels[12] & 0x07FF)<<4);
+ packet[18] = (uint8_t) ((channels[12] & 0x07FF)>>4 | (channels[13] & 0x07FF)<<7);
+ packet[19] = (uint8_t) ((channels[13] & 0x07FF)>>1);
+ packet[20] = (uint8_t) ((channels[13] & 0x07FF)>>9 | (channels[14] & 0x07FF)<<2);
+ packet[21] = (uint8_t) ((channels[14] & 0x07FF)>>6 | (channels[15] & 0x07FF)<<5);
+ packet[22] = (uint8_t) ((channels[15] & 0x07FF)>>3);
+ }
+ // flags
+ packet[23] = 0x00;
+ // footer
+ packet[24] = _sbusFooter;
+ #if defined(__MK20DX128__) || defined(__MK20DX256__) // Teensy 3.0 || Teensy 3.1/3.2
+ // use ISR to send byte at a time,
+ // 130 us between bytes to emulate 2 stop bits
+ noInterrupts();
+ memcpy(&PACKET,&packet,sizeof(packet));
+ interrupts();
+ serialTimer.priority(255);
+ serialTimer.begin(sendByte,130);
+ #else
+ // write packet
+ _bus->write(packet,25);
+ #endif
+}
+
+/* write SBUS packets from calibrated inputs */
+void SBUS::writeCal(float* calChannels)
+{
+ uint16_t channels[_numChannels] = {0};
+ // linear calibration
+ if (calChannels) {
+ for (uint8_t i = 0; i < _numChannels; i++) {
+ if (_useWriteCoeff[i]) {
+ calChannels[i] = PolyVal(_writeLen[i],_writeCoeff[i],calChannels[i]);
+ }
+ channels[i] = (calChannels[i] - _sbusBias[i]) / _sbusScale[i];
+ }
+ }
+ write(channels);
+}
+
+void SBUS::setEndPoints(uint8_t channel,uint16_t min,uint16_t max)
+{
+ _sbusMin[channel] = min;
+ _sbusMax[channel] = max;
+ scaleBias(channel);
+}
+
+void SBUS::getEndPoints(uint8_t channel,uint16_t *min,uint16_t *max)
+{
+ if (min&&max) {
+ *min = _sbusMin[channel];
+ *max = _sbusMax[channel];
+ }
+}
+
+void SBUS::setReadCal(uint8_t channel,float *coeff,uint8_t len)
+{
+ if (coeff) {
+ if (!_readCoeff) {
+ _readCoeff = (float**) malloc(sizeof(float*)*_numChannels);
+ }
+ if (!_readCoeff[channel]) {
+ _readCoeff[channel] = (float*) malloc(sizeof(float)*len);
+ } else {
+ free(_readCoeff[channel]);
+ _readCoeff[channel] = (float*) malloc(sizeof(float)*len);
+ }
+ for (uint8_t i = 0; i < len; i++) {
+ _readCoeff[channel][i] = coeff[i];
+ }
+ _readLen[channel] = len;
+ _useReadCoeff[channel] = true;
+ }
+}
+
+void SBUS::getReadCal(uint8_t channel,float *coeff,uint8_t len)
+{
+ if (coeff) {
+ for (uint8_t i = 0; (i < _readLen[channel]) && (i < len); i++) {
+ coeff[i] = _readCoeff[channel][i];
+ }
+ }
+}
+
+void SBUS::setWriteCal(uint8_t channel,float *coeff,uint8_t len)
+{
+ if (coeff) {
+ if (!_writeCoeff) {
+ _writeCoeff = (float**) malloc(sizeof(float*)*_numChannels);
+ }
+ if (!_writeCoeff[channel]) {
+ _writeCoeff[channel] = (float*) malloc(sizeof(float)*len);
+ } else {
+ free(_writeCoeff[channel]);
+ _writeCoeff[channel] = (float*) malloc(sizeof(float)*len);
+ }
+ for (uint8_t i = 0; i < len; i++) {
+ _writeCoeff[channel][i] = coeff[i];
+ }
+ _writeLen[channel] = len;
+ _useWriteCoeff[channel] = true;
+ }
+}
+
+void SBUS::getWriteCal(uint8_t channel,float *coeff,uint8_t len)
+{
+ if (coeff) {
+ for (uint8_t i = 0; (i < _writeLen[channel]) && (i < len); i++) {
+ coeff[i] = _writeCoeff[channel][i];
+ }
+ }
+}
+
+/* destructor, free dynamically allocated memory */
+SBUS::~SBUS()
+{
+ if (_readCoeff) {
+ for (uint8_t i = 0; i < _numChannels; i++) {
+ if (_readCoeff[i]) {
+ free(_readCoeff[i]);
+ }
+ }
+ free(_readCoeff);
+ }
+ if (_writeCoeff) {
+ for (uint8_t i = 0; i < _numChannels; i++) {
+ if (_writeCoeff[i]) {
+ free(_writeCoeff[i]);
+ }
+ }
+ free(_writeCoeff);
+ }
+}
+
+/* parse the SBUS data */
+bool SBUS::parse()
+{
+ // reset the parser state if too much time has passed
+ static elapsedMicros _sbusTime = 0;
+ if (_sbusTime > SBUS_TIMEOUT_US) {_parserState = 0;}
+ // see if serial data is available
+ while (_bus->available() > 0) {
+ _sbusTime = 0;
+ _curByte = _bus->read();
+ // find the header
+ if (_parserState == 0) {
+ if ((_curByte == _sbusHeader) && ((_prevByte == _sbusFooter) || ((_prevByte & _sbus2Mask) == _sbus2Footer))) {
+ _parserState++;
+ } else {
+ _parserState = 0;
+ }
+ } else {
+ // strip off the data
+ if ((_parserState-1) < _payloadSize) {
+ _payload[_parserState-1] = _curByte;
+ _parserState++;
+ }
+ // check the end byte
+ if ((_parserState-1) == _payloadSize) {
+ if ((_curByte == _sbusFooter) || ((_curByte & _sbus2Mask) == _sbus2Footer)) {
+ _parserState = 0;
+ return true;
+ } else {
+ _parserState = 0;
+ return false;
+ }
+ }
+ }
+ _prevByte = _curByte;
+ }
+ // return false if a partial packet
+ return false;
+}
+
+/* compute scale factor and bias from end points */
+void SBUS::scaleBias(uint8_t channel)
+{
+ _sbusScale[channel] = 2.0f / ((float)_sbusMax[channel] - (float)_sbusMin[channel]);
+ _sbusBias[channel] = -1.0f*((float)_sbusMin[channel] + ((float)_sbusMax[channel] - (float)_sbusMin[channel]) / 2.0f) * _sbusScale[channel];
+}
+
+float SBUS::PolyVal(size_t PolySize, float *Coefficients, float X) {
+ if (Coefficients) {
+ float Y = Coefficients[0];
+ for (uint8_t i = 1; i < PolySize; i++) {
+ Y = Y*X + Coefficients[i];
+ }
+ return(Y);
+ } else {
+ return 0;
+ }
+}
+
+// function to send byte at a time with
+// ISR to emulate 2 stop bits on Teensy 3.0 and 3.1/3.2
+#if defined(__MK20DX128__) || defined(__MK20DX256__) // Teensy 3.0 || Teensy 3.1/3.2
+ void sendByte()
+ {
+ if (SENDINDEX < 25) {
+ SERIALPORT->write(PACKET[SENDINDEX]);
+ SENDINDEX++;
+ } else {
+ serialTimer.end();
+ SENDINDEX = 0;
+ }
+ }
+#endif
diff --git a/Versions/dRehmFlight_ESP32_BETA_1.3/src/SBUS/SBUS.h b/Versions/dRehmFlight_ESP32_BETA_1.3/src/SBUS/SBUS.h
new file mode 100644
index 00000000..215cb9b7
--- /dev/null
+++ b/Versions/dRehmFlight_ESP32_BETA_1.3/src/SBUS/SBUS.h
@@ -0,0 +1,82 @@
+/*
+ SBUS.h
+ Brian R Taylor
+ [email protected]
+
+ Copyright (c) 2016 Bolder Flight Systems
+
+ This program is free software: you can redistribute it and/or modify
+ it under the terms of the GNU General Public License as published by
+ the Free Software Foundation, either version 3 of the License, or
+ (at your option) any later version.
+
+ This program is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ GNU General Public License for more details.
+
+ You should have received a copy of the GNU General Public License
+ along with this program. If not, see .
+*/
+
+#ifndef SBUS_h
+#define SBUS_h
+
+#include "Arduino.h"
+#include "elapsedMillis.h"
+
+/*
+* Hardware Serial Supported:
+* Teensy 3.0 || Teensy 3.1/3.2 || Teensy 3.5 || Teensy 3.6 || Teensy LC || STM32L4 || Maple Mini || Arduino Mega 2560 || ESP32
+*/
+#if defined(__MK20DX128__) || defined(__MK20DX256__) || defined(__MK64FX512__) \
+ || defined(__MK66FX1M0__) || defined(__MKL26Z64__) || defined(__IMXRT1052__) \
+ || defined(STM32L496xx) || defined(STM32L476xx) || defined(STM32L433xx) \
+ || defined(STM32L432xx) || defined(_BOARD_MAPLE_MINI_H_) \
+ || defined(__AVR_ATmega2560__) || defined(ESP32)
+#endif
+
+class SBUS{
+ public:
+ SBUS(HardwareSerial& bus);
+ void begin();
+ bool read(uint16_t* channels, bool* failsafe, bool* lostFrame);
+ bool readCal(float* calChannels, bool* failsafe, bool* lostFrame);
+ void write(uint16_t* channels);
+ void writeCal(float *channels);
+ void setEndPoints(uint8_t channel,uint16_t min,uint16_t max);
+ void getEndPoints(uint8_t channel,uint16_t *min,uint16_t *max);
+ void setReadCal(uint8_t channel,float *coeff,uint8_t len);
+ void getReadCal(uint8_t channel,float *coeff,uint8_t len);
+ void setWriteCal(uint8_t channel,float *coeff,uint8_t len);
+ void getWriteCal(uint8_t channel,float *coeff,uint8_t len);
+ ~SBUS();
+ private:
+ const uint32_t _sbusBaud = 100000;
+ static const uint8_t _numChannels = 16;
+ const uint8_t _sbusHeader = 0x0F;
+ const uint8_t _sbusFooter = 0x00;
+ const uint8_t _sbus2Footer = 0x04;
+ const uint8_t _sbus2Mask = 0x0F;
+ const uint32_t SBUS_TIMEOUT_US = 7000;
+ uint8_t _parserState, _prevByte = _sbusFooter, _curByte;
+ static const uint8_t _payloadSize = 24;
+ uint8_t _payload[_payloadSize];
+ const uint8_t _sbusLostFrame = 0x04;
+ const uint8_t _sbusFailSafe = 0x08;
+ const uint16_t _defaultMin = 172;
+ const uint16_t _defaultMax = 1811;
+ uint16_t _sbusMin[_numChannels];
+ uint16_t _sbusMax[_numChannels];
+ float _sbusScale[_numChannels];
+ float _sbusBias[_numChannels];
+ float **_readCoeff, **_writeCoeff;
+ uint8_t _readLen[_numChannels],_writeLen[_numChannels];
+ bool _useReadCoeff[_numChannels], _useWriteCoeff[_numChannels];
+ HardwareSerial* _bus;
+ bool parse();
+ void scaleBias(uint8_t channel);
+ float PolyVal(size_t PolySize, float *Coefficients, float X);
+};
+
+#endif
diff --git a/Versions/dRehmFlight_ESP32_BETA_1.3/src/SBUS/elapsedMillis.h b/Versions/dRehmFlight_ESP32_BETA_1.3/src/SBUS/elapsedMillis.h
new file mode 100644
index 00000000..48cff11d
--- /dev/null
+++ b/Versions/dRehmFlight_ESP32_BETA_1.3/src/SBUS/elapsedMillis.h
@@ -0,0 +1,81 @@
+/* Elapsed time types - for easy-to-use measurements of elapsed time
+ * http://www.pjrc.com/teensy/
+ * Copyright (c) 2017 PJRC.COM, LLC
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy
+ * of this software and associated documentation files (the "Software"), to deal
+ * in the Software without restriction, including without limitation the rights
+ * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+ * copies of the Software, and to permit persons to whom the Software is
+ * furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+ * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+ * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+ * THE SOFTWARE.
+ */
+
+#ifndef elapsedMillis_h
+#define elapsedMillis_h
+#ifdef __cplusplus
+
+#if ARDUINO >= 100
+#include "Arduino.h"
+#else
+#include "WProgram.h"
+#endif
+
+class elapsedMillis
+{
+private:
+ unsigned long ms;
+public:
+ elapsedMillis(void) { ms = millis(); }
+ elapsedMillis(unsigned long val) { ms = millis() - val; }
+ elapsedMillis(const elapsedMillis &orig) { ms = orig.ms; }
+ operator unsigned long () const { return millis() - ms; }
+ elapsedMillis & operator = (const elapsedMillis &rhs) { ms = rhs.ms; return *this; }
+ elapsedMillis & operator = (unsigned long val) { ms = millis() - val; return *this; }
+ elapsedMillis & operator -= (unsigned long val) { ms += val ; return *this; }
+ elapsedMillis & operator += (unsigned long val) { ms -= val ; return *this; }
+ elapsedMillis operator - (int val) const { elapsedMillis r(*this); r.ms += val; return r; }
+ elapsedMillis operator - (unsigned int val) const { elapsedMillis r(*this); r.ms += val; return r; }
+ elapsedMillis operator - (long val) const { elapsedMillis r(*this); r.ms += val; return r; }
+ elapsedMillis operator - (unsigned long val) const { elapsedMillis r(*this); r.ms += val; return r; }
+ elapsedMillis operator + (int val) const { elapsedMillis r(*this); r.ms -= val; return r; }
+ elapsedMillis operator + (unsigned int val) const { elapsedMillis r(*this); r.ms -= val; return r; }
+ elapsedMillis operator + (long val) const { elapsedMillis r(*this); r.ms -= val; return r; }
+ elapsedMillis operator + (unsigned long val) const { elapsedMillis r(*this); r.ms -= val; return r; }
+};
+
+class elapsedMicros
+{
+private:
+ unsigned long us;
+public:
+ elapsedMicros(void) { us = micros(); }
+ elapsedMicros(unsigned long val) { us = micros() - val; }
+ elapsedMicros(const elapsedMicros &orig) { us = orig.us; }
+ operator unsigned long () const { return micros() - us; }
+ elapsedMicros & operator = (const elapsedMicros &rhs) { us = rhs.us; return *this; }
+ elapsedMicros & operator = (unsigned long val) { us = micros() - val; return *this; }
+ elapsedMicros & operator -= (unsigned long val) { us += val ; return *this; }
+ elapsedMicros & operator += (unsigned long val) { us -= val ; return *this; }
+ elapsedMicros operator - (int val) const { elapsedMicros r(*this); r.us += val; return r; }
+ elapsedMicros operator - (unsigned int val) const { elapsedMicros r(*this); r.us += val; return r; }
+ elapsedMicros operator - (long val) const { elapsedMicros r(*this); r.us += val; return r; }
+ elapsedMicros operator - (unsigned long val) const { elapsedMicros r(*this); r.us += val; return r; }
+ elapsedMicros operator + (int val) const { elapsedMicros r(*this); r.us -= val; return r; }
+ elapsedMicros operator + (unsigned int val) const { elapsedMicros r(*this); r.us -= val; return r; }
+ elapsedMicros operator + (long val) const { elapsedMicros r(*this); r.us -= val; return r; }
+ elapsedMicros operator + (unsigned long val) const { elapsedMicros r(*this); r.us -= val; return r; }
+};
+
+#endif // __cplusplus
+#endif // elapsedMillis_h
diff --git a/Versions/dRehmFlight_ESP32_BETA_1.3/src/TFMPlus/TFMPlus.cpp b/Versions/dRehmFlight_ESP32_BETA_1.3/src/TFMPlus/TFMPlus.cpp
new file mode 100644
index 00000000..8a4a63a3
--- /dev/null
+++ b/Versions/dRehmFlight_ESP32_BETA_1.3/src/TFMPlus/TFMPlus.cpp
@@ -0,0 +1,385 @@
+/* File Name: TFMPlus.cpp
+ * Version: 1.5.0
+ * Described: Arduino Library for the Benewake TFMini-Plus Lidar sensor
+ * The TFMini-Plus is a unique product, and the various
+ * TFMini Libraries are not compatible with the Plus.
+ * Developer: Bud Ryerson
+ * Inception: v0.2.0 - 31 JAN 2019
+ * v1.0.0 - 25FEB19 - Initial release
+ * v1.0.1 - 09MAR19 - 'build()' function always returned TRUE.
+ Corrected to return FALSE if serial data is not available.
+ And other minor corrections to textual descriptions.
+ * v1.1.0 - 13MAR19 - To simplify, all interface functions now
+ return boolean. Status code is still set and can be read.
+ 'testSum()' is deleted and 'makeSum()' is used instead.
+ Example code is updated.
+ * v1.1.1 - 14MAR19 - Two commands: RESTORE_FACTORY_SETTINGS
+ and SAVE_SETTINGS were not defined correctly.
+ * v1.2.1 - 02APR19 - Rewrote 'getData()' function to make it faster
+ and more robust when serial read skips a byte or fails entirely.
+ * v1.3.1 - 08APR19 - Redefined commands to include response length
+ ********************** IMPORTANT ************************
+ **** Changed name of 'buildCommand()' to 'sendCommand()'. ****
+ ****************************************************************
+ * v.1.3.2 - Added a line to getData() to flush the serial buffer
+ of all but last frame of data before reading. This does not
+ effect usage, but will ensure that the latest data is read.
+ * v.1.3.3 - 20MAY19 - Changed 'sendCommand()' to add a second byte,
+ to the HEADER recognition routine, the reply length byte.
+ This makes recognition of the command reply more robust.
+ Zeroed out 'data frame' snd 'command reply' buffer arrays
+ completely before reading from device. Added but did not
+ implement some I2C command codes.
+ * v.1.3.4 - 07JUN19 - Added 'TFMP_' to all error status defines.
+ The ubiquitous 'Arduino.h' also contains a 'SERIAL' define.
+ * v.1.3.5 - 25OCT19 - Added missing underscore to parameter
+ in header file TFMPlus.h:
+ Line 138 #define BAUD_14400 0x003840
+ * v.1.3.6 - 27APR20 - a little cleanup in 'getData()'
+ * v.1.4.0 - 15JUN20 - Changed all data variables from unsigned
+ to signed integers. Defined abnormal data codes
+ as per TFMini-S Producut Manual
+ - - - - - - - - - - - - - - -
+ Dist | Strength | Comment
+ -1 Other value Strength ≤ 100
+ -2 -1 Signal strength saturation
+ -4 Other value Ambient light saturation
+ - - - - - - - - - - - - - - -
+ * v.1.4.1 - 22JUL20 - Fixed bug in sendCommand() checksum calculation
+ - Changed two printf()s to Serial.print()s
+ - Fixed printReply() to show data from 'reply' rather than 'frame'
+ * v.1.4.2 - 19MAY21 - Changed command paramter 'FRAME_5' to correct value.
+ It was set to 0x0003. Now it's set to 0x0005
+ * v.1.5.0 - 06SEP21 - Corrected (reversed) Enable/Disable commands in 'TFMPlus.h'
+ Changed three command names
+ OBTAIN_FIRMWARE_VERSION is now GET_FIRMWARE_VERSION
+ RESTORE_FACTORY_SETTINGS is now HARD_RESET
+ SYSTEM_RESET is now SOFT_RESET
+ *
+ * Default settings for the TFMini-Plus are a 115200 serial baud rate
+ * and a 100Hz measurement frame rate. The device will begin returning
+ * measurement data immediately on power up.
+ *
+ * 'begin()' function passes a serial stream to library and
+ * returns TRUE/FALSE whether serial data is available.
+ * Function also sets a public one byte status code.
+ * Status codes are defined within the library.
+ *
+ * 'getData( dist, flux, temp)' passes back measurement data
+ * • dist = distance in centimeters,
+ * • flux = signal strength in arbitrary units, and
+ * • temp = an encoded number in degrees centigrade
+ * Function returns TRUE/FALSE whether completed without error.
+ * Error, if any, is saved as a one byte 'status' code.
+ *
+ * 'sendCommand( cmnd, param)' sends a 32bit command code (cmnd)
+ * and a 32bit parameter value (param). Returns TRUE/FALSE and
+ * sets a one byte status code.
+ * Commands are selected from the library's list of defined commands.
+ * Parameter values can be entered directly (115200, 250, etc) but
+ * for safety, they should be chosen from the Library's defined lists.
+ * An incorrect value can render the device uncommunicative.
+ *
+ */
+
+#include "TFMPlus.h"
+//#include // Future I2C Implementation
+
+// Constructor
+TFMPlus::TFMPlus(){}
+TFMPlus::~TFMPlus(){}
+
+// Return TRUE/FALSE whether receiving serial data from
+// device, and set system status to provide more information.
+bool TFMPlus::begin(Stream *streamPtr)
+{
+ pStream = streamPtr; // Save reference to stream/serial object.
+ delay( 10); // Delay for device data in serial buffer.
+ if( (*pStream).available()) // If data present...
+ {
+ status = TFMP_READY; // set status to READY
+ return true; // and return TRUE.
+ }
+ else // Otherwise...
+ {
+ status = TFMP_SERIAL; // set status to SERIAL error
+ return false; // and return false.
+ }
+}
+
+bool TFMPlus::getData( int16_t &dist, int16_t &flux, int16_t &temp)
+{
+ // - - - - - - - - - - - - - - - - - - - - - - - - - - - -
+ // Step 1 - Get data from the device.
+ // - - - - - - - - - - - - - - - - - - - - - - - - - - - -
+ // Set timer to one second timeout if HEADER never appears
+ // or serial data never becomes available.
+ uint32_t serialTimeout = millis() + 1000;
+
+ if( !(*pStream).available())
+ {
+ return false;
+ }
+
+ // Flush all but last frame of data from the serial buffer.
+ while( (*pStream).available() > TFMP_FRAME_SIZE) (*pStream).read();
+
+ // Zero out the entire frame data buffer.
+ memset( frame, 0, sizeof( frame));
+
+ // Read one byte from the serial buffer into the last byte of
+ // the frame buffer, then left shift the whole array one byte.
+ // Repeat until the two HEADER bytes show up as the first
+ // two bytes in the array.
+ while( ( frame[ 0] != 0x59) || ( frame[ 1] != 0x59))
+ {
+ if( (*pStream).available())
+ {
+ // Read one byte into the framebuffer's
+ // last plus one position.
+ frame[ TFMP_FRAME_SIZE] = (*pStream).read();
+ // Shift the last nine bytes one byte left.
+ memcpy( frame, frame + 1, TFMP_FRAME_SIZE);
+ }
+ // If HEADER or serial data are not available
+ // after more than one second...
+ if( millis() > serialTimeout)
+ {
+ status = TFMP_HEADER; // then set error...
+ return false; // and return "false".
+ }
+ }
+
+ // - - - - - - - - - - - - - - - - - - - - - - - - - - - -
+ // Step 2 - Perform a checksum test.
+ // - - - - - - - - - - - - - - - - - - - - - - - - - - - -
+ // Clear the 'chkSum' variable declared in 'TFMPlus.h'
+ chkSum = 0;
+ // Add together all bytes but the last.
+ for( uint8_t i = 0; i < ( TFMP_FRAME_SIZE - 1); i++) chkSum += frame[ i];
+ // If the low order byte does not equal the last byte...
+ if( ( uint8_t)chkSum != frame[ TFMP_FRAME_SIZE - 1])
+ {
+ status = TFMP_CHECKSUM; // then set error...
+ return false; // and return "false."
+ }
+
+ // - - - - - - - - - - - - - - - - - - - - - - - - - - - -
+ // Step 3 - Interpret the frame data
+ // and if okay, then go home
+ // - - - - - - - - - - - - - - - - - - - - - - - - - - - -
+ dist = frame[ 2] + ( frame[ 3] << 8);
+ flux = frame[ 4] + ( frame[ 5] << 8);
+ temp = frame[ 6] + ( frame[ 7] << 8);
+ // Convert temp code to degrees Celsius.
+ temp = ( temp >> 3) - 256;
+ // Convert Celsius to degrees Farenheit
+ // temp = uint8_t( temp * 9 / 5) + 32;
+
+ // - - Evaluate Abnormal Data Values - -
+ // Values are from the TFMini-S Product Manual
+ // Signal strength <= 100
+ if( dist == -1) status = TFMP_WEAK;
+ // Signal Strength saturation
+ else if( flux == -1) status = TFMP_STRONG;
+ // Ambient Light saturation
+ else if( dist == -4) status = TFMP_FLOOD;
+ // Data is apparently okay
+ else status = TFMP_READY;
+
+ if( status != TFMP_READY) return false;
+ else return true;
+}
+
+// Pass back only the distance data
+bool TFMPlus::getData( int16_t &dist)
+{
+ static int16_t flux, temp;
+ return getData( dist, flux, temp);
+}
+
+// = = = = = SEND A COMMAND TO THE DEVICE = = = = = = = = = =0
+//
+// Create a proper command byte array, send the command,
+// get a repsonse, and return the status
+bool TFMPlus::sendCommand( uint32_t cmnd, uint32_t param)
+{
+ // - - - - - - - - - - - - - - - - - - - - - - - - - - - -
+ // Step 1 - Build the command data to send to the device
+ // - - - - - - - - - - - - - - - - - - - - - - - - - - - -
+ static uint8_t cmndLen; // Length of command
+ static uint8_t replyLen; // Length of command reply data
+ static uint8_t cmndData[ 8]; // 8 byte send command array
+
+ memset( cmndData, 0, 8); // Clear the send command array.
+ memcpy( &cmndData[ 0], &cmnd, 4); // Copy 4 bytes of data: reply length,
+ // command length, command number and
+ // a one byte parameter, all encoded as
+ // a 32 bit unsigned integer.
+
+ replyLen = cmndData[ 0]; // Save the first byte as reply length.
+ cmndLen = cmndData[ 1]; // Save the second byte as command length.
+ cmndData[ 0] = 0x5A; // Set the first byte to HEADER code.
+
+ if( cmnd == SET_FRAME_RATE) // If the command is Set FrameRate...
+ {
+ memcpy( &cmndData[ 3], ¶m, 2); // add the 2 byte FrameRate parameter.
+ }
+ else if( cmnd == SET_BAUD_RATE) // If the command is Set BaudRate...
+ {
+ memcpy( &cmndData[ 3], ¶m, 4); // add the 3 byte BaudRate parameter.
+ }
+
+ // Create a checksum byte for the command data array.
+ chkSum = 0;
+ // Add together all bytes but the last...
+ for( uint8_t i = 0; i < ( cmndLen - 1); i++) chkSum += cmndData[ i];
+ // and save it as the last byte of command data.
+ cmndData[ cmndLen - 1] = (uint8_t)chkSum;
+
+ // - - - - - - - - - - - - - - - - - - - - - - - - - - - -
+ // Step 2 - Send the command data array to the device
+ // - - - - - - - - - - - - - - - - - - - - - - - - - - - -
+ while( (*pStream).available()) (*pStream).read(); // flush input buffer
+ (*pStream).flush(); // flush output buffer
+ for( uint8_t i = 0; i < cmndLen; i++) (*pStream).write( cmndData[ i]);
+
+
+ // + + + + + + + + + + + + + + + + + + + + + + + + +
+ // If the command does not expect a reply, then we're
+ // finished here. Call the getData() function instead.
+ if( replyLen == 0) return true;
+ // + + + + + + + + + + + + + + + + + + + + + + + + +
+
+
+ // - - - - - - - - - - - - - - - - - - - - - - - - - - - -
+ // Step 3 - Get command reply data back from the device.
+ // - - - - - - - - - - - - - - - - - - - - - - - - - - - -
+ // Set a one second timer to timeout if HEADER never appears
+ // or serial data never becomes available
+ uint32_t serialTimeout = millis() + 1000;
+ // Clear out the entire command reply data buffer
+ memset( reply, 0, sizeof( reply));
+ // Read one byte from the serial buffer into the end of
+ // the reply buffer and then left shift the whole array.
+ // Repeat until the HEADER byte and reply length byte
+ // show up as the first two bytes in the array.
+ while( ( reply[ 0] != 0x5A) || ( reply[ 1] != replyLen))
+ {
+ if( (*pStream).available())
+ {
+ // Read one byte into the reply buffer's
+ // last-plus-one position.
+ reply[ replyLen] = (*pStream).read();
+ // Shift the last nine bytes one byte left.
+ memcpy( reply, reply+1, TFMP_REPLY_SIZE);
+ }
+ // If HEADER pattern or Serial data are not available
+ // after more than one second...
+ if( millis() > serialTimeout)
+ {
+ status = TFMP_TIMEOUT; // then set error...
+ return false; // and return "false".
+ }
+ }
+
+ // - - - - - - - - - - - - - - - - - - - - - - - - - - - -
+ // Step 4 - Perform a checksum test.
+ // - - - - - - - - - - - - - - - - - - - - - - - - - - - -
+ // Clear the 'chkSum' variable declared in 'TFMPlus.h'
+ chkSum = 0;
+ // Add together all bytes but the last...
+ for( uint8_t i = 0; i < ( replyLen - 1); i++) chkSum += reply[ i];
+ // If the low order byte of the Sum does not equal the last byte...
+ if( reply[ replyLen - 1] != (uint8_t)chkSum)
+ {
+ status = TFMP_CHECKSUM; // then set error...
+ return false; // and return "false."
+ }
+
+ // - - - - - - - - - - - - - - - - - - - - - - - - - - - -
+ // Step 5 - Interpret different command responses.
+ // - - - - - - - - - - - - - - - - - - - - - - - - - - - -
+ if( cmnd == GET_FIRMWARE_VERSION)
+ {
+ version[ 0] = reply[5]; // set firmware version.
+ version[ 1] = reply[4];
+ version[ 2] = reply[3];
+ }
+ else
+ {
+ if( cmnd == SOFT_RESET ||
+ cmnd == HARD_RESET ||
+ cmnd == SAVE_SETTINGS )
+ {
+ if( reply[ 3] == 1) // If PASS/FAIL byte not zero ...
+ {
+ status = TFMP_FAIL; // set status 'FAIL'...
+ return false; // and return 'false'.
+ }
+ }
+ }
+
+ // - - - - - - - - - - - - - - - - - - - - - - - - - - - -
+ // Step 6 - Set READY status and go home
+ // - - - - - - - - - - - - - - - - - - - - - - - - - - - -
+ status = TFMP_READY;
+ return true;
+}
+
+// - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
+// - - - - - The following is for testing purposes - - - -
+// - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
+
+// Called by either 'printFrame()' or 'printReply()'
+// Print status condition either 'READY' or error type
+void TFMPlus::printStatus()
+{
+ Serial.print("Status: ");
+ if( status == TFMP_READY) Serial.print( "READY");
+ else if( status == TFMP_SERIAL) Serial.print( "SERIAL");
+ else if( status == TFMP_HEADER) Serial.print( "HEADER");
+ else if( status == TFMP_CHECKSUM) Serial.print( "CHECKSUM");
+ else if( status == TFMP_TIMEOUT) Serial.print( "TIMEOUT");
+ else if( status == TFMP_PASS) Serial.print( "PASS");
+ else if( status == TFMP_FAIL) Serial.print( "FAIL");
+ else if( status == TFMP_I2CREAD) Serial.print( "I2C-READ");
+ else if( status == TFMP_I2CWRITE) Serial.print( "I2C-WRITE");
+ else if( status == TFMP_I2CLENGTH) Serial.print( "I2C-LENGTH");
+ else if( status == TFMP_WEAK) Serial.print( "Signal weak");
+ else if( status == TFMP_STRONG) Serial.print( "Signal saturation");
+ else if( status == TFMP_FLOOD) Serial.print( "Ambient light saturation");
+ else Serial.print( "OTHER");
+ Serial.println();
+}
+
+// Print error type and HEX values
+// of each byte in the data frame
+void TFMPlus::printFrame()
+{
+ printStatus();
+ // Print the Hex value of each byte of data
+ Serial.print("Data:");
+ for( uint8_t i = 0; i < TFMP_FRAME_SIZE; i++)
+ {
+ Serial.print(" ");
+ Serial.print( frame[ i] < 16 ? "0" : "");
+ Serial.print( frame[ i], HEX);
+ }
+ Serial.println();
+}
+
+// Print error type and HEX values of
+// each byte in the command response frame.
+void TFMPlus::printReply()
+{
+ printStatus();
+ // Print the Hex value of each byte
+ for( uint8_t i = 0; i < TFMP_REPLY_SIZE; i++)
+ {
+ Serial.print(" ");
+ Serial.print( reply[ i] < 16 ? "0" : "");
+ Serial.print( reply[ i], HEX);
+ }
+ Serial.println();
+}
diff --git a/Versions/dRehmFlight_ESP32_BETA_1.3/src/TFMPlus/TFMPlus.h b/Versions/dRehmFlight_ESP32_BETA_1.3/src/TFMPlus/TFMPlus.h
new file mode 100644
index 00000000..64721987
--- /dev/null
+++ b/Versions/dRehmFlight_ESP32_BETA_1.3/src/TFMPlus/TFMPlus.h
@@ -0,0 +1,227 @@
+/* File Name: TFMPlus.h
+ * Version: 1.5.0
+ * Described: Arduino Library for the Benewake TFMini-Plus Lidar sensor
+ * The TFMini-Plus is a unique product, and the various
+ * TFMini Libraries are not compatible with the Plus.
+ * Developer: Bud Ryerson
+ * Inception: v0.2.0 - 31 JAN 2019
+ * v1.0.0 - 25FEB19 - Initial release
+ * v1.0.1 - 09MAR19 - 'build()' function always returned TRUE.
+ Corrected to return FALSE if serial data is not available.
+ And other minor corrections to textual descriptions.
+ * v1.1.0 - 13MAR19 - To simplify, all interface functions now
+ return boolean. Status code is still set and can be read.
+ 'testSum()' is deleted and 'makeSum()' is used instead.
+ Example code is updated.
+ * v1.1.1 - 14MAR19 - Two commands: RESTORE_FACTORY_SETTINGS
+ and SAVE_SETTINGS were not defined correctly.
+ * v1.2.1 - 02APR19 - Rewrote 'getData()' function to make it faster
+ and more robust when serial read skips a byte or fails entirely.
+ * v1.3.1 - 08APR19 - Redefined commands to include response length
+ ********************** IMPORTANT ************************
+ **** Changed name of 'buildCommand()' to 'sendCommand()'. ****
+ ****************************************************************
+ * v.1.3.2 - Added a line to getData() to flush the serial buffer
+ of all but last frame of data before reading. This does not
+ effect usage, but will ensure that the latest data is read.
+ * v.1.3.3 - 20MAY19 - Changed 'sendCommand()' to add a second byte,
+ to the HEADER recognition routine, the reply length byte.
+ Zeroed out 'data frame' snd 'command reply' buffer arrays
+ completely before reading from device. Added but did not
+ implement some I2C command codes.
+ * v.1.3.4 - 07JUN19 - Added 'TFMP_' to all error status defines.
+ The ubiquitous 'Arduino.h' also contains a 'SERIAL' define.
+ * v.1.3.5 - 25OCT19 - Added missing underscore to paramter:
+ #define BAUD_14400 0x003840
+ * v.1.3.6 - 27APR20 - a little cleanup in 'getData()'
+ * v.1.4.0 - 15JUN20
+ 1. Changed all data variables from unsigned to signed integers.
+ 2. Defined abnormal data codes as per TFMini-S Producut Manual
+ - - - - - - - - - - - - - - - -
+ Distance | Strength | Comment
+ -1 Other value Strength ≤ 100
+ -2 -1 Signal strength saturation
+ -4 Other value Ambient light saturation
+ - - - - - - - - - - - - - - - -
+ * v.1.4.1 - 22JUL20 - Fixed bugs in TFMPlus.cpp
+ * v.1.5.0 - 06SEP21 - Corrected (reversed) Enable/Disable commands
+ Changed three command names
+ OBTAIN_FIRMWARE_VERSION is now GET_FIRMWARE_VERSION
+ RESTORE_FACTORY_SETTINGS is now HARD_RESET
+ SYSTEM_RESET is now SOFT_RESET
+ *
+ * Default settings for the TFMini-Plus are a 115200 serial baud rate
+ * and a 100Hz measurement frame rate. The device will begin returning
+ * measurement data immediately on power up.
+ *
+ * 'begin()' function passes a serial stream to library and
+ * returns TRUE/FALSE whether serial data is available.
+ * Function also sets a public one byte status code.
+ * Status codes are defined within the library.
+ *
+ * 'getData( dist, flux, temp)' passes back measurement data
+ * • dist = distance in centimeters,
+ * • flux = signal strength in arbitrary units, and
+ * • temp = an encoded number in degrees centigrade
+ * Function returns TRUE/FALSE whether completed without error.
+ * Error, if any, is saved as a one byte 'status' code.
+ *
+ * 'sendCommand( cmnd, param)' sends a 32bit command code (cmnd)
+ * and a 32bit parameter value (param). Returns TRUE/FALSE and
+ * sets a one byte status code.
+ * Commands are selected from the library's list of defined commands.
+ * Parameter values can be entered directly (115200, 250, etc) but
+ * for safety, they should be chosen from the Library's defined lists.
+ * An incorrect value can render the device uncommunicative.
+ *
+ */
+
+#ifndef TFMPLUS_H // Guard to compile only once
+#define TFMPLUS_H
+
+#include // Always include this. It's important.
+
+// Buffer sizes
+#define TFMP_FRAME_SIZE 9 // Size of data frame = 9 bytes
+#define TFMP_REPLY_SIZE 8 // Longest command reply = 8 bytes
+#define TFMP_COMMAND_MAX 8 // Longest command = 8 bytes
+
+// Timeout Limits for various functions
+#define TFMP_MAX_READS 20 // readData() sets SERIAL error
+#define MAX_BYTES_BEFORE_HEADER 20 // getData() sets HEADER error
+#define MAX_ATTEMPTS_TO_MEASURE 20
+
+#define TFMP_DEFAULT_ADDRESS 0x10 // default I2C slave address
+ // as hexidecimal integer
+// System Error Status Condition
+#define TFMP_READY 0 // no error
+#define TFMP_SERIAL 1 // serial timeout
+#define TFMP_HEADER 2 // no header found
+#define TFMP_CHECKSUM 3 // checksum doesn't match
+#define TFMP_TIMEOUT 4 // I2C timeout
+#define TFMP_PASS 5 // reply from some system commands
+#define TFMP_FAIL 6 // "
+#define TFMP_I2CREAD 7
+#define TFMP_I2CWRITE 8
+#define TFMP_I2CLENGTH 9
+#define TFMP_WEAK 10 // Signal Strength ≤ 100
+#define TFMP_STRONG 11 // Signal Strength saturation
+#define TFMP_FLOOD 12 // Ambient Light saturation
+#define TFMP_MEASURE 13
+
+
+/* - - - - - - - - - TFMini Plus - - - - - - - - -
+ Data Frame format:
+ Byte0 Byte1 Byte2 Byte3 Byte4 Byte5 Byte6 Byte7 Byte8
+ 0x59 0x59 Dist_L Dist_H Flux_L Flux_H Temp_L Temp_H CheckSum_
+ Data Frame Header character: Hex 0x59, Decimal 89, or "Y"
+
+ Command format:
+ Byte0 Byte1 Byte2 Byte3 to Len-2 Byte Len-1
+ 0x5A Length Cmd ID Payload if any Checksum
+ - - - - - - - - - - - - - - - - - - - - - - - - - */
+
+// The library 'sendCommand( cmnd, param)' function
+// defines a command (cmnd) in the the following format:
+// 0x 00 00 00 00
+// one byte command command reply
+// payload number length length
+#define GET_FIRMWARE_VERSION 0x00010407 // returns 3 byte firmware version
+#define TRIGGER_DETECTION 0x00040400 // must have set frame rate to zero
+ // returns a 9 byte data frame
+#define SOFT_RESET 0x00020405 // returns a 1 byte pass/fail (0/1)
+#define HARD_RESET 0x00100405 // "
+#define SAVE_SETTINGS 0x00110405 // This must follow every command
+ // that modifies volatile parameters.
+ // Returns a 1 byte pass/fail (0/1)
+
+#define SET_FRAME_RATE 0x00030606 // These commands each return
+#define SET_BAUD_RATE 0x00060808 // an echo of the command
+#define STANDARD_FORMAT_CM 0x01050505 // "
+#define PIXHAWK_FORMAT 0x02050505 // "
+#define STANDARD_FORMAT_MM 0x06050505 // "
+#define ENABLE_OUTPUT 0x01070505 // "
+#define DISABLE_OUTPUT 0x00070505 // "
+#define SET_I2C_ADDRESS 0x100B0505 // "
+
+#define SET_SERIAL_MODE 0x000A0500 // default is Serial (UART)
+#define SET_I2C_MODE 0x010A0500 // set device as I2C slave
+
+#define I2C_FORMAT_CM 0x01000500 // returns a 9 byte data frame
+#define I2C_FORMAT_MM 0x06000500 // "
+
+// * * * * * * * Description of I/O Mode * * * * * * *
+// Normally, device Pin 3 is either Serial transmit (TX) or I2C clock (SCL).
+// When 'I/O Mode' is set other than 'Standard,' Pin 3 becomes a simple HI/LO
+// (near/far) binary output. Thereafter, only Pin 2, the Serial RX line, is
+// functional, and only Serial data sent to the device is possible.
+//#define SET_IO_MODE_STANDARD 0x003B0900 // 'Standard' is default mode
+//#define SET_IO_MODE_HILO 0x013B0900 // I/O, near high and far low
+//#define SET_IO_MODE_LOHI 0x023B0900 // I/O, near low and far high
+// * * * This library does not support the I/O Mode interface * * *
+
+// Command Parameters
+#define BAUD_9600 0x002580 // UART serial baud rate
+#define BAUD_14400 0x003840 // expressed in hexidecimal
+#define BAUD_19200 0x004B00
+#define BAUD_56000 0x00DAC0
+#define BAUD_115200 0x01C200
+#define BAUD_460800 0x070800
+#define BAUD_921600 0x0E1000
+
+#define FRAME_0 0x0000 // internal measurement rate
+#define FRAME_1 0x0001 // expressed in hexidecimal
+#define FRAME_2 0x0002
+#define FRAME_5 0x0005 // incorrectly set to 3 in prior versions
+#define FRAME_10 0x000A
+#define FRAME_20 0x0014
+#define FRAME_25 0x0019
+#define FRAME_50 0x0032
+#define FRAME_100 0x0064
+#define FRAME_125 0x007D
+#define FRAME_200 0x00C8
+#define FRAME_250 0x00FA
+#define FRAME_500 0x01F4
+#define FRAME_1000 0x03E8
+
+// Object Class Definitions
+class TFMPlus
+{
+ public:
+ TFMPlus();
+ ~TFMPlus();
+
+ uint8_t version[ 3]; // to save firmware version
+ uint8_t status; // to save library error status
+
+ // Return T/F whether serial data available, set error status if not.
+ bool begin( Stream *streamPtr);
+ // Read device data and pass back three values
+ bool getData( int16_t &dist, int16_t &flux, int16_t &temp);
+ // Short version, passes back distance data only
+ bool getData( int16_t &dist);
+ // Build and send a command, and check response
+ bool sendCommand( uint32_t cmnd, uint32_t param);
+
+ // For testing purposes: print frame or reply data and status
+ // as a string of HEX characters
+ void printFrame();
+ void printReply();
+ bool getResponse();
+
+ private:
+ Stream* pStream; // pointer to the device serial stream
+ // The data buffers are one byte longer than necessary
+ // because we read one byte into the last position, then
+ // shift the whole array left by one byte after each read.
+ uint8_t frame[ TFMP_FRAME_SIZE + 1];
+ uint8_t reply[ TFMP_REPLY_SIZE + 1];
+
+ uint16_t chkSum; // to calculate the check sum byte.
+
+ // for testing - called by 'printFrame()' or 'printReply()'
+ void printStatus();
+
+};
+
+#endif